• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.109-112
• /
• 2003

Small impedances in the superconducting parallel circuits cause unequal distribution of the currents in the circuits. This results in quenches or losses in some superconducting parts and decrease of total transport current. This paper presents the fabrication and test results of a superconducting multi- interphase transformers (SIPT) for equal current distribution in superconducting parallel circuits. The secondary loop configuration with air core SIPT seems to be the most efficient one for the SFCL. Test results show that the SIPT can effectively make the current distribution uniform in Parallel circuits that have unequal resistances.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.396-403
• /
• 2011

In this study, we investigated the mechanical behaviors of layered thermal barrier coatings by indentations. Various single and double-layered thermal barrier coatings were deposited by air plasma spray process using different type of commercialized YSZ (Yttria stabilized zirconia) starting powders. Indentation stress-strain curve, load-displacement curve and hardness of the single and the double-layered thermal barrier coatings were obtained experimentally and analyzed. The indentation damages at the same loads were compared, and thus, the results depend on the structure of each coating. The result indicates improvement in damage resistances from tailoring of layered structures in the component of gas turbine system is expected.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.111-120
• /
• 2009

This paper presents a fundamental findings of the functional and structural performance of the porous asphalt concrete coated with MMA resin. To evaluate the structural performance, cantabro, wheel tracking, moisture sensitivity and indirect tensile fatigue tests are performed. The tests results show that the cantabro loss is reduced three times and fatigue resistance is significantly increased after the specimens are coated with MMA resin. However there are little changes in the rutting and moisture damage resistances before and after the coating. Air voids, permeability and BPT(British Pendulum Test) tests are conducted to study the functional performance. It is observed form the tests that the air voids and permeability are slightly decreased after the coating. However, the changes in the air voids and permeability are negligible. The skid resistance of the coated specimens is lower than reference specimens. However, the skid resistance is maintained beyond the level of the reference specimens when silica sands are chipped on top of the coated surface.

• Journal of Korean Society of Water and Wastewater
• /
• v.25 no.4
• /
• pp.591-596
• /
• 2011

Surface floating air cathode microbial fuel cell (MFC) having horizontal flow was developed for the application of MFC technology. RVC (Reticulated vitreous carbon) coated with anyline was used as anode electrode and carbon cloth coated with Pt (5.0 g Pt/$m^2$, GDE LT250EW, E-TEK) was used as cathode electrode. As results of continuous operation with changing the flow rate from 4.3 mL/min to 9.5 mL/min, maximum power density of 4.5 W/$m^3$ was acquired at 5.4 mL/min, which was at 0.35 m/hr of flow velocity under anode electrode. When the ratio of cathode surface area to anode surface area($A_c/A_a$) was changed to 1.0, 0.5, and 0.25, the maximum power density of 2.7 W/$m^3$ was shown at the ratio of 1.0. As the ratio decreased from 1.0 to 0.25, the power density also decreased, which is caused by increasing the internal resistance resulted from reducing the surface area to contact with oxygen. Actually, internal resistances of the ratio of 1.0, 0.5, and 0.25 were 63.75${\Omega}$, 142.18${\Omega}$, and 206.12${\Omega}$, respectively.

• Korean Journal of Soil Science and Fertilizer
• /
• v.29 no.4
• /
• pp.411-418
• /
• 1996

This experiment was conducted to investigate the effect of electric conductivity (EC) and potassium (K) concentration level in the culture solution on the growth and the air pollution monitoring capability of Perilla frutescens Suwon 16 which was recognized as a possible bioindicator for air pollution. The plants were exposed to $NO_2$, $O_3$, $SO_2$ and $NO_2+SO_2$ within a phytotron at $25^{\circ}C$ (day) or at $20^{\circ}C$(night) with 70% of relative humidity and evaluated the effect of EC and K level on the injury of the plants, The highest dry weights were gained as 16.3 g/plant at 0.5 dS/m of EC and as 32.3 g/plant at 100 and 200mg/l of K concentration, respectively. The diffusive resistances appeared as low values at 0.5 dS/m of EC and at 50, 100mg/l of K concentration. The increasing of the visible injury with increasing the dose of air pollutants could be taken at 0.5. 1.0 ds/m of EC and at 50, 100mg/l of K. The recommendable level of EC and K of the culture solution were 0.5-1.0 dS/m of electric conductivity. 50-100mg/l of K for the plant as an air pollutant biomonitor, when the 7th or 8th leaf was developed.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.37 no.5
• /
• pp.715-723
• /
• 2013

This develops a new and advanced S/S knitwear material made of linen/bamboo blended yarn. Linen/bamboo knitted fabrics were compared with linen/polyester knitted fabrics in terms of appearance as well as physical and comfort properties. Rib knitted fabrics were remarkably thicker than plain knitted fabrics. Knitted fabrics based on polyester yarns were heavier than those based on bamboo yarn. The porosity decreased in the following order: linen 100% > bamboo 100% > polyester 100%. The drape properties of bamboo 100% and linen/bamboo knitted fabrics were excellent. The pilling resistances of linen 100% and linen/bamboo knitted fabrics were excellent. The highest and lowest air permeability was observed in the case of linen/bamboo knitted fabrics and polyester 100% knitted fabrics, respectively. The instant cool-feeling was enhanced as the bamboo yarns were blended. The thermal conductivity of linen 100% knitted fabrics was the highest and the thermal conductivity of linen/bamboo knitted fabrics was higher than linen/polyester knitted fabrics. Bamboo 100% knitted fabrics showed a higher moisture regain than polyester 100% knitted fabrics. The results confirmed the superior appearance and comfort of a novel S/S knit wear material made of linen/bamboo knitted fabric.

• Journal of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.555-560
• /
• 1990

High temperature superconducting films of $YBa_2Cu_3O_{7-x}$ were fabricated on the (100) single crystal faces of YSZ (yttria stabilized zirconia) and SrTi$O_3$ by aerosol spray using ultrasonic atomization. The superconducting phase was formed by a three-step process: (a) spraying of a stoichiometric solution of nitrates of yttrium, barium, and copper on heated substrates kept at 250$^{\circ}C$, (b) preheating of the sprayed films in air at 550$^{\circ}C$, and (e) sintering of the films in flowing oxygen at 950$^{\circ}C$, followed by furnace cooling. Resistances of the films were measured by the dc four-probe method and superconductivity was confirmed above the liquid nitrogen temperature.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.2
• /
• pp.113-120
• /
• 2010

Air-cathode microbial fuel cell consisted of 4 unit cells were operated under batch condition and electricity generation and microbial community structure variation were investigated, depending on separator types and cathode characteristics: A) PEM(Proton Exchange Membrane)-30% Wet proofing Carbon Cloth(WC), B) AEM(Anion Exchange Membrane-WC, C) CEM(Cation Exchange Membrane)-WC, D) PEM-No Wet proofing Carbon Cloth(NC). Maximum power densities of PEM-WC, AEM-WC and CEM-WC were 510.9, 522.1 and 504.8 $mW/m^2$, respectively. But PEM-NC showed relatively lower maximum power density of 218.3 $mW/m^2$. And PEM-WC, AEM-WC and CEM-WC showed similar internal resistances(20.0-28.2 ${\Omega}$). PCRDGGE, PCA and diversity indices showed that uncultured bacteria which reported in previous MFC studies were detected in suspended growth bacteria and attached growth bacteria would be affected not by separator type but by cathode characteristic. Thus, cathode characteristic can be one of the critical factors for power generation in air-cathode MFC using PEM, AEM, and CEM as separator.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.6 no.6
• /
• pp.572-581
• /
• 2001

A heat pipe heat sink device which is to evacuate maximum heat of about 1800W from a powersemiconductor was designed and manufactured One set of cooling device os composed of an Aluminum block (130${\times}$160${\times}$35mm) 4 PFC heat pipes $(d_0 22.23mm)$ and 126 Aluminium fins (250${\times}$58${\times}$0.8mm) Experimental data obtained at a power of 1~2kW revealed that the total thermal resistance of the device varied 0.02~0.018$^{\circ}C$/W along with increasing air velocity from 2m/s to 3 m/s. The result represented a good satisfaction of requirement condition to maintain temperature rise of semiconductor lowe that $40^{\circ}C$ at 1800W and air velocity of 3 m/s Some important resistance such as convective resistances at both fins and heat pipes showed good agreement between mathematical predictions and measurement data.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.3
• /
• pp.189-196
• /
• 2008

The increase of system weight due to installation of cooling devices adds electrical and mechanical loads of humanoid robot, and in return, results in much heat. Therefore, the weight of cooling system is a critical issue for robot cooling. In this study, we propose non-metallic cold plates to deal with such problems. We compare thermal performances between one metallic cold plate and five different types of non-metallic cold plates. A metallic cold plate is totally made of copper. Five non-metallic PC(polycarbonate) cold plates, which are designed to reduce the overall weight of robot cooling system, are composed of a polycarbonate cover with different types of base plate. The overall heat transfer coefficients per unit mass and thermal resistances are obtained for the cold plates. The metallic cold plate shows the best thermal performance. It is interesting to note that the PC cold plate with an aluminum base plate with 18 channels shows the best overall heat transfer coefficient per unit mass. Most polycarbonate cold plates display fairly comparable thermal performance with more reduced system weight compared to the metallic cold plate.