• Journal of Power System Engineering
• /
• v.4 no.3
• /
• pp.34-39
• /
• 2000

Performance data in the literature on air lift pumps have been based primarily on pumps of long length and large diameter (high lift pumps). Since mariculture operations involve pumps of relatively short length and small diameter, performance data are required for efficient operation. To provide such data, an experimental apparatus was designed and fabricated to test all lift pumps from 2.1 to 3.4 cm inside diameter and from 40 to 300 cm in length. Instrumentation was provided to measure water flow rate and air flow rate as well as water temperature, air temperature, and pressure throughout the system. Results from this study correlate well with high lift pump data in that, for a given pump geometry, maximum water flow occurs for a specific air flow rate. Driving the pump with air flows larger or smaller than this optimum flow rate will decrease the pumping rate. The optimum flows are significantly different for low lift pumps compared to high lift pumps. However, the pumping rate for low lift pumps approaches that for high lift pumps with increasing length.

• Journal of Soil and Groundwater Environment
• /
• v.15 no.6
• /
• pp.91-98
• /
• 2010

The effective thermal conductivity of porous materials is usually determined by porosity, water content, and the conductivity of the matrix. In addition, it is also affected by the internal structure of the materials such as the size, arrangement, and connectivity of the matrix-forming grains. Based on the structural models for multi-phase materials, thermal conductivities of soils and sands measured with varying the water content were analyzed. Thermal conductivities of dry samples were likely to fall in the region between the Maxwell-Eucken model with air as the continuous phase and the matrix as the dispersed phase ($ME_{air}$) and the co-continuous (CC) model. However, water-saturated samples moved down to the region between the $ME_{wat}$ model and the series model. The predictive inconsistency of the structural models for dry and water-saturated samples may be caused by the increase of porosity for water-saturated samples, which leads to decrease of connectivity among the grains of matrix. In cases of variably saturated samples with a uniform grain size, the thermal conductivity showed progressive changes of the structural models from the $ME_{air}$ model to the $ME_{wat}$ model depending on the water content. Especially, an abrupt increase found in 0-20% of the water content, showing transition from the $ME_{air}$ model to the CC model, can be attributed to change of water from the dispersed to continuous phase. On the contrary, the undisturbed soil samples with various sizes of grains showed a gradual increase of conductivity during the transition from the $ME_{air}$ model to the CC model.

• Explosives and Blasting
• /
• v.28 no.2
• /
• pp.28-36
• /
• 2010

A study about economical blasting methods which can improve fragmentation and save explosive in blasting is in progress. One of the blasting methods is an air decking method making air layers in boreholes. However, it is difficult to apply this method to the boreholes filled with water. In this study, an underwater Air Tube was manufactured and tried to place it at a certain location in a water filled borehole. It was found that the application of underwater air tube in wet boreholes could improve the fragmentation and save 10~15% of the explosives.

• Water Engineering Research
• /
• v.5 no.4
• /
• pp.195-206
• /
• 2004

This paper deals with oxygen transfer by air entrainment and energy dissipations by flow characteristics at the stepped drop structure. Nappe flow occurred at low flow rates and for relatively large step height. Dominant flow features included an air pocket, a free-falling nappe impact and a subsequent hydraulic jump on the downstream step. Most energy was dissipated by nappe impact and in the downstream hydraulic jump. Skimming flow occurred at larger flow rates with formation of recirculating vortices between the main flow and the step comers. Oxygen transfer was found to be proportional to the flow velocity, the flow discharge, and the Froude number. It was more related to the flow discharge than to the Froude number. Energy dissipations in both cases of nappe flow and skimming flow were proportional to the step height and were inversely proportional to the overflow depth, and were not proportional to the step slope. The stepped drop structure was found to be efficient for water treatment associated with substantial air entrainment and for energy dissipation.

• Nuclear Engineering and Technology
• /
• v.53 no.12
• /
• pp.3892-3901
• /
• 2021

The pressure drop of a moisture separator in a steam generator is the important design parameter to ensure the successful performance of a nuclear power plant. The moisture separators have a wide range of operating conditions based on the arrangement of them. The prediction of the pressure drop in a moisture separator is challenging due to the complexity of the multi-dimensional two-phase vortex flow. In this study, the moisture separator test facility using the air/water two-phase flow was used to predict the pressure drop of a moisture separator in a Korean OPR-1000 reactor. The prototypical steam/water two-phase flow conditions in a steam generator were simulated as air/water two-phase flow conditions by preserving the centrifugal force and vapor quality. A series of experiments were carried out to investigate the effect of hydraulic characteristics such as the quality and liquid mass flux on the two-phase pressure drop. A new prediction model based on the scaling law was suggested and validated experimentally using the full and half scale of separators. The suggested prediction model showed good agreement with the steam/water experimental results, and it can be extended to predict the steam/water two-phase pressure drop for moisture separators.

• Nuclear Engineering and Technology
• /
• v.46 no.6
• /
• pp.817-824
• /
• 2014

To ensure the safety of research reactors, the water level must be maintained above the required height. When a pipe ruptures, the siphon phenomenon causes continuous loss of coolant until the hydraulic head is removed. To protect the reactor core from this kind of accident, a siphon breaker has been suggested as a passive safety device. This study mainly focused on two variables: the size of the pipe rupture and the timing of air entrainment. In this study, the size of the pipe rupture was increased to the guillotine break case. There was a region in which a larger pipe rupture did not need a larger siphon breaker, and the water flow rate was related to the size of the pipe rupture and affected the residual water quantity. The timing of air entrainment was predicted to influence residual water level. However, the residual water level was not affected by the timing of air entrainment. The experimental cases, which showed the characteristic of partical sweep-out mode in the separation of siphon breaking phenomenon [2], showed almost same trend of physical properties.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.2
• /
• pp.128-135
• /
• 2007

In response to anthropogenic global warming due to a buildup greenhouse gas, the effect of the air temperature on water temperature has been noticed. Therefore, effects have been made to build an air/water temperature relationship at three study regions using the data collected by the Ministry of the Maritime Affairs and Fisheries (MOMAF). The air/water relationship varies with time-scale and weekly time-scale was chosen for the study. The data were fitted to the S-shaped non-linear relationship, and the parameters for the S-curve were derived using a single-criteria multi-parameter optimization scheme. Separate regression curves were fitted to consider seasonal hysteresis at the Masan site. The study results support the S-shaped non-linear relationship is the best fit for the air/water relationship at the Korean coastal zone. This study will contribute to determine the future policy regarding water quality and ecosystem for the decision-driving organization.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.19 no.3
• /
• pp.213-221
• /
• 2007

In response to anthropogenic global warming due to a buildup greenhouse gas, the effect of the air temperature on water temperature has been noticed and some efforts have been made to build an air/water temperature relationship at the Masan Bay area by the Ministry of Maritime Affairs & Fisheries (MOMAF). As a result of analyzing the auto- and cross-correlation coefficient between air/water temperature, high correlation $(\sim0.9)$ is shown and the correlation coefficient of air temperature is higher than that of water temperature at the lag time less than approximately 10 days. Separate functions are fitted to the air/water relationship at the Masan Bay to take hysteresis into account. The slopes of the straight line for the rising limb are 0.829 and 0.774 for MA1 and MA2 station respectively, while 1.385 and 1.444 ($\sim1.75$ times larger) for the falling limb. Consequently, the seasonal hysteresis should be considered in order to determine an air/water relationship and accurately estimate the water temperature using the air temperature at Masan Bay.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.4
• /
• pp.297-305
• /
• 2012

In recent large-scale semiconductor manufacturing clean rooms, the energy consumption of outdoor air conditioning systems to heat, humidify, cool and dehumidify incoming outdoor air represents about 45% of the total air conditioning load required to maintain a clean room environment. Therefore, the energy performance evaluation and analysis of outdoor air conditioning systems is useful for reducing the outdoor air conditioning load for a clean room. In the present study, an experiment was conducted to compare the energy consumption of outdoor air conditioning systems with a simple air washer, an exhaust air heat recovery type air washer and a DCC return water heat recovery type air washer. It was shown from the present lab-scale experiment with an outdoor air flow of 1,000 $m^3/h$ that the exhaust air heat recovery type and DCC return water heat recovery type air washer outdoor air conditioning systems were more energy-efficient for the summer and winter operations than the simple air washer outdoor air conditioning system and furthermore, the DCC return water heat recovery type one was the most energy-efficient in the winter operation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.04a
• /
• pp.33-40
• /
• 1997

This study was undertaken to investigate tribology characteristics of the alumina ceramics($Al_2O_3$) for the vauiation of ambient condition such as air and distilled water. The results obtained were as follows. As the sliding speed increases, the friction coefficient in the air decreased due to the reduction of sheafing stress caused by the heat accumulation of contact interface. And the friction coefficient in the distilled water decreased due to an activation of the tribochemical reaction. As the contact load increases, the friction coefficient is small in the air due to temperature rise of the contact interface. However, at the low speed side in the distilled water, the friction coefficient holds a large value due to decrease of the tribochemical reaction. The friction surface of ceramics can be protected in the air by the influence of the oxides tansfered from STB2 and also in the distilled water by the influence of the corrosive productive hydroxides.