• Journal of the Korea institute for structural maintenance and inspection
• /
• 제24권1호
• /
• pp.59-66
• /
• 2020

In this study, self - healing solid capsules of crystal growth type which can be mixed directly with repair mortar were prepared, and the quality and crack healing performance of repair mortar with self - healing solid capsules were evaluated. The table flow and the air flow rate of the repair mortar material mixed with self-healing solid capsules were found to have no significant influence on table flow and air volume regardless of mixing ratio. Compressive strength tended to decrease with increasing capsule mixing ratio. As a result of evaluation of crack healing properties according to constant water head permeability test, initial water permeability decreased, and reaction products were generated over time and cracks were healed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제23권1호
• /
• pp.113-121
• /
• 2019

In this study, self - healing microcapsules which can be mixed directly with cement composites were prepared, and the quality and crack healing performance of cement composites with self - healing microcapsules were evaluated. In the past, it has been focused on evaluating self-healing capsules and crack healing properties. Therefore, self - healing microcapsules have been studied for their effect on the quality of cement composites when mixed with cement composites. The table flow and the air flow rate of the cement composite material mixed with self-healing microcapsules were found to have no significant influence on table flow and air volume regardless of mixing ratio. Compressive strength and splitting tensile strength tended to decrease with increasing capsule mixing ratio. As a result of evaluation of crack healing properties according to water flow, initial water permeability decreased, and reaction products were generated over time and cracks were healed.

• Safety and Health at Work
• /
• 제14권2호
• /
• pp.237-242
• /
• 2023

Background: This study evaluated occupational exposure levels of doxorubicin in healthcare workers performing rotational intraperitoneal pressurized aerosol chemotherapy (PIPAC) procedures. Methods: All samples were collected during PIPAC procedures applying doxorubicin to an experimental animal model (pigs). All procedures were applied to seven pigs, each for approximately 44 min. Surface samples (n = 51) were obtained from substances contaminating the PIPAC devices, surrounding objects, and protective equipment. Airborne samples were also collected around the operating table (n = 39). All samples were analyzed using ultra-high performance liquid chromatography-mass spectrometry. Results: Among the surface samples, doxorubicin was detected in only five samples (9.8%) that were directly exposed to antineoplastic drug aerosols in the abdominal cavity originating from PIPAC devices. The telescopes showed concentrations of 0.48-5.44 ng/cm² and the trocar showed 0.98 ng/cm² in the region where the spraying nozzles were inserted. The syringe line connector showed a maximum concentration of 181.07 ng/cm², following a leakage. Contamination was not detected on the surgeons' gloves or shoes. Objects surrounding the operating table, including tables, operating lights, entrance doors, and trocar holders, were found to be uncontaminated. All air samples collected at locations where healthcare workers performed procedures were found to be uncontaminated. Conclusions: Most air and surface samples were uncontaminated or showed very low doxorubicin concentrations during PIPAC procedures. However, there remains a potential for leakage, in which case dermal exposure may occur. Safety protocols related to leakage accidents, selection of appropriate protective equipment, and the use of disposable devices are necessary to prevent occupational exposure.

• Journal of the Korean Wood Science and Technology
• /
• 제25권2호
• /
• pp.52-60
• /
• 1997

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split- resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent, wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heat ed f or 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Journal of the Korean Wood Science and Technology
• /
• 제11권2호
• /
• pp.52-60
• /
• 1983

Hornbeam trees(Carpinus laxiflora BL.) are growing in Korea and have good characteristics such as relatively high density, fine texture, split-resistance, and white colour. However, they have seldom been used as manufacturing materials This study was carried out to evaluate the possibility of using hornbeam wood as bent-wood furniture materials. Softening methods were steaming and micro-wave heating. The specimens of $15{\times}15{\times}350mm$ were used green or air-dried, and were steamed at $100^{\circ}C$ for 20min, or microwave heated for 60 seconds. The bending processing conditions are showed in Table 3. The minimum solid-bending radii of air-dried wood were 40mm for steaming and 200mm for micro-wave heating, respectively. And that of green wood were 40mm for micro-wave heating. In conclusion, both of the steamed wood and micro-wave heated green wood showed very good solid bending processing properties, but micro-wave heated air-dried wood were not sufficient for bent-wood furniture.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• 제26권4호
• /
• pp.445-453
• /
• 2016

Objectives: The objective of this study is to assess relative safety level of the decompression tables in Ministry of Employment and Labor Public Notice No. 2014-28 in comparison with overseas decompression tables. Methods: Decompression tables in the Public Notice No. 2014-28 were compared with examples from Japan, the USA, Canada, and France in terms of ascent rate, surface intervals after exceptional exposures, oxygen decompression and allowable partial pressure, depth limits in air diving, no-decompression limits, and decompression time and methods. Results: Public Notice No. 2014-28 does not include air diving depth limits, exceptional exposure limits, mandatory surface intervals after exceptional exposures, oxygen decompression, and surface decompression schedules. Its decompression time was found to be the shortest among the five decompression tables. Conclusions: Public Notice No. 2014-28 has the lowest safety level in comparison with overseas decompression tables. Deck decompression chambers are not applicable due to no regulations on surface interval and oxygen use in the chamber for decompression.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• 제23권5호
• /
• pp.435-442
• /
• 2014

This paper describes an improved design model that can be used to configure a non-contact pneumatic device to turn a large sheet at the in-line system. For rotational moving in the conveyor system, the conventional method is to turn the system itself. The improved non-contact pick-up system mainly uses 8 pairs of L-shaped latches and 12 swirl type heads. It is positioned above the upward air flow table. This system performs the non-contact gripping and side-edge contact support in the vertical and rotational directions to hold the self-weight of a large flat sheet. A non-contact air head can exert a sufficient gripping ability at 4N lower than the standard working pressure. The side latches support 60% of the lifting force required. Through structural and flow analysis, the working conditions were simultaneously considered in accordance with the deflection and flatness of the glass.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• 제5권2호
• /
• pp.50-56
• /
• 1972

This study has been carried out to observe the driving and the intercepting effects of air screen on some sea-water fishes ; Chrysophrys major, Mylio macrocephalus, Fugu pardalis. 1. By perforating fine holes on the compressed air pipes, air screen was formed in the water, and this screen was set at $45^{\circ}$, and $90^{\circ}$ against the fish passage to observe the reactions on the part of the fish. 2. Changes were given to the location of the air screen in the water to observe how the air screen drived the fish to its direction. 3. The effective distance between holes on the air piprs was determined by a series of experiments of setting up two air screens of various types in hole distance, by moving a screen to-ward the other, and of observing the distance between two screens when fish eseape through the space. The results of the above experiments observed as follows were : 1. The passage of fish was effectively intercepted by setting up the air screens at 45 degrees against the fish passage and it was also intercepted when the screen was set at 90 degrees against the passage. 2. Fish could be driven by moving the air screen toward the fish. 3. The air screen formed from the pipe above than 0.3mm in diameter was effective, but less than 0.2mm was not sufficiently effective. 4. The strength of the air pressure in the pipe should be higher than $0.087kg/cm^2$. 5. The fish holding ability to obtain effective air screen was ranged as following when the air pressure was $0.160kg/cm^2$. and the hole diameter was 0.3mm on the 12.6mm pipe, depending upon the intervals of the holes on the pipe: The shortest distance which could hold fish between two screens was 59.4cm when the holes were perforated at every 40cm; 33.5cm when at every 30cm; 28.75cm when at every 10cm: and 27.25cm when at every 5cm. Thus, no significant change was at served when the holes were perforated more densely than 30cm intervals. Therefor the hole intervals should be 30cm in designing fishing gear employing air screen.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• 제4권2호
• /
• pp.168-179
• /
• 1994

In some ceramic industries, worker exposure to dust, crystalline free silica and lead were determined and evaluated. The conclusions are as follows. 1. Crystalline silica in bulk samples was 10.5 % in sanitary ware industry, 9.4 % in tile industry, and 2.1 % in ceramic insulator industry respectively. The free silica content of air filter sample was 8.03 % in table ware industry, 5.59 % in sanitary ware industry, and 1.32 % in ceramic insulator industry. Because silica content in ceramic dust is relatively high, it is should be considered silica as important factor in evaluating for ceramic industry. 2. The silica contents in dust from tile, sanitary ware and table ware industries are above 5%, it should be classified as "Type" 2 dust. 3. The airborne concentration of respirable crystalline silica was $27.9{\mu}g/m^3$ in a sanitary ware factory and $5.8{\mu}g/m^3$ in a ceramic insualtor factory. Three of ten samples sampled the above factories were exceeded the occupational exposure levels, $100{\mu}g/m^3$. 4. Geometric mean(GM) of total dust in 11 factories was $1.00mg/m^3$ and GM of respirable dust concentration in 5 factories was $0.33mg/m^3$. Sanitary ware industry had the highest concentration of total dust, $1.62mg/m^3$ and of respirable dust, $0.88mg/m^3$. 5. Average lead concentration in air was $0.05mg/m^3$ in glazing process of 2 factories manufacturing table ware. Five of ten sample(50%) were exceeded $0.05mg/m^3$. Therefore lead exposure in pottery industry should be considered as important problem.

• Journal of Food Hygiene and Safety
• /
• 제26권4호
• /
• pp.361-365
• /
• 2011

To evaluate the indoor air quality of food manufacturing plants, the presence of viable bacteria and fungi was assessed in the indoor air of the facilities at which 9 food items were manufactured. Air samples were collected from the general zone, low clean zone and clean zone of each factory with an air sampler, in combination with plate counts agar using for bacteria, and dichloran-glycerol agar for fungi. The samples were incubated at $25^{\circ}C$ for 4 to 7 days. After culture, the colony forming units (CFU) on each plate were counted and corrected with a positive hole conversion table. The average concentration of bacteria was $2.2{\times}10^3\;CFU/m^3$ in the general zone, $1.2{\times}10^3\;CFU/m^3$ in the low clean zone and $7.3{\times}10^2\;CFU/m^3$ in the clean zone. The average concentration of fungal microbes was $2.5{\times}10^3\;CFU/m^3$ in the general zone, $2.6{\times}10^3\;CFU/m^3$ in the low clean zone, and $2.0{\times}10^2\;CFU/m^3$ in the clean zone. No meaningful differences were detected between the general zone and the low clean zone, but the clean zone had significantly lower concentrations than the other zones. Additionally, the identification of the fungi was performed according to morphological method using a giant culture and slide culture. The fungi were identified as belonging to 18 genera, and the genera Cladosporium(33%), Penicillium(29%) and Aspergillus(26%), predominated. Aspergillus isolates were identified to species level, and A. ochraceus, a mycotoxigenic species, was identified. As part of the effort to control the quality of the indoor air of food manufacturing plants, our results show that continued studies are clearly warranted.