• 한국유체기계학회 논문집
• /
• 제20권1호
• /
• pp.74-80
• /
• 2017

Pump sump system or pumping stations are built to draw water from a source such as river and used for irrigation, thermal power plants etc. If pump sump is improperly shaped or sized, air entraining vortices or submerged vortices may develop. This may greatly affect pump operation if vortices grow to an appreciable extent. Moreover, the noise and vibration of the pump can be increased by the remaining of vortices in the pump flow passage. Therefore, the vortices in the pump flow passage have to be reduced for a good performance of pump sump station. In this study, the effect of pump intake leaning angle and flow rate on the pump sump internal flow has been investigated. There are three cases with different leaning angle. Moreover, a pipe type with elbow also has been studied. The flow rate with three classes of air entraining vortices has been examined and investigated by decreasing the water level. The result shows that the air entraining vortices easily occurs at the pump intake with large leaning angle. Moreover, the elbow type of the pump intake easily occurs air entraining vortices at the high flow rate (or velocity) in comparison to other pump intake type.

• International Journal of Advanced Culture Technology
• /
• 제3권1호
• /
• pp.1-12
• /
• 2015

The current scenario of the transportation sector reflects the urgent need to address issues such as depletion of traditional fuel reserves and ever growing pollution levels. Researchers around the world are focussing on alternatives as well as optimisation of currently employed devices to reduce the pollution levels generated by the commonly used fuels. One such optimisation involves the study of air flow within the intake manifolds of SI engines. It is a well-known fact that alterations in the air manifolds of engines have a significant impact on the engine performance parameters, fuel consumption and emission levels. Previous works have demonstrated the impacts of runner lengths, diameter, plenum volume, taper angle of distribution manifolds and other factors on in-cylinder fluid motion and engine performance. However, a static setup provides an optimal configuration only at a specific engine speed. This paper aims to investigate the variations in the same parameters on a four stroke, naturally aspirated single cylinder SI engine through varying the cross section design over the intake runner with the aid of Computational Fluid Dynamics. The system consists of segments that form the intake runner with projections on the inside that allow various permutations of the intake runner segments. The various configurations provide the optimised fluid flow characteristics within the intake manifold at specific engine speed intervals. The variations such as turbulence, air fuel mixing are analysed using the three dimensional CFD software FLUENT. The results can be used further for developing an automated or manually adjustable intake manifold.

• 한국항공운항학회지
• /
• 제23권3호
• /
• pp.8-17
• /
• 2015

In this research, low fidelity air/heat load analysis was conducted for the intake of high speed vehicle. For air/heat load calculations, aerodynamic properties at the surface and the boundary layer edge were estimated using Taylor-Maccoll equation for conical flow, shockwave relation and Prandtl-Meyer expansion equation for internal and external flow. Couette flow assumption and Reynolds analogy were used in order to calculate convective heat transfer coefficient. In order to calculate skin friction coefficient for heat transfer coefficient analysis, Van Driest method II and Reference Enthalpy method were considered. An axis symmetric SCRAMJET model was selected as a reference configuration for verifying the proper implementation of the present method. Comparison of the results using the present method and Computational Fluid Dynamic analysis showed that the present method is valuable for efficiently providing pressure and heat loads for air-intake structure design of the high speed air vehicle.

• 드라이브 ㆍ 컨트롤
• /
• 제10권2호
• /
• pp.23-29
• /
• 2013

The excavator is used in a variety of construction environments. There are many kinds of risk like falling rocks or harmful dust. The excavator cabin protects the operator not only from these harmful environments but also provides a comfortable working environment. By the way, the excavator cabin consumes a lot of energy for cabin air conditioner. For this reason, the research is required to reduce energy consumption. This study suggests the air conditioning system for excavator using forced exhaust. First, the forced exhaust system simulated by AMESim tool and surveyed the applicability. Using AMESim simulation, it was investigated the effect of cabin inside temperature by intake flow rate and intake air temperature. The experiment executed using the 1.5 ton excavator and field tested according to the intake flow rate. Finally, verified the applicability on the air conditioning system for excavator using forced exhaust.

• 설비공학논문집
• /
• 제16권1호
• /
• pp.8-15
• /
• 2004

Since the vehicle is regarded as the third living space, the comfortable conditions are required in the passenger compartment. For this reason, customers are concerned about the filtering performances and the importance of filter media has been greatly placed. Therefore the dust holding capacity, the efficiency of these filter media (dry paper, wet paper, non-woven) and the configuration of air filter for vehicle were measured in this study. The following results were obtained on the basis of air filter test. It shows that the thickness and poresize of filter media should be lower for the higher efficiency. The measurement result shows that the performance of round shape filters are higher than the square shape filters. The dust holding capacity of the wet paper and the non-woven paper is higher than the dry paper. As a result, this research can provide an important design parameter and product guidance of the intake air filter for vehicular engine.

• 한국자동차공학회논문집
• /
• 제2권2호
• /
• pp.49-58
• /
• 1994

A study on the performance of a Diesel engine with various intake gas compositions other than that of air are performed experimentally. In this study, the concentrations of each of oxygen, nitorgen, carbon dioxide, and argon are changed and their effects on the performance of the engine are investigated parametrically. The experiments are performed at constant engine speed condition, and main measured parameters are cylinder pressure, intake gas compositions, fuel consumption rate. Increase of oxygen concentration up to 24% improved the performance of the engine generally. The adverse effect was observed when the oxygen concentration was increased over 24%. Increase of carbon dioxide concentration degraded the performance of the engine, mainly due to the lower specific heat ratio of carbon dioxide. Adding argon gas to the intake gas improved the overall performance. Finally, it is found that two most influencing factors affecting the performance of the Diesel engine in this study of intake gas composition variation are ignition delay and specific heat ratio of the intake gas.

• 한국분무공학회지
• /
• 제26권2호
• /
• pp.81-87
• /
• 2021

This study was performed to calculate the swirl ratio of a diesel engine intake port by a 1D computer simulation under actual engine operating conditions. The swirl ratio of the intake port was simulated according to the change of the engine speed during the operation of the motoring without fuel injection. The swirl ratio of the intake port was simulated according to changes in the crank angle during the four-cycle operation of intake, compression, expansion and exhaust. The swirl ratio represented by the three regions of the piston, center and squish was simulated. Among the three regions, the piston-region swirl ratio is important for effective air-fuel mixing in the engine cylinder. In particular, it was confirmed during the simulation that the piston swirl ratio before and after the compression top dead center (TDC) point when fuel is injected in the DI diesel engine can have a significant effect on the mixing of air and fuel. It was desirable to set the average piston swirl ratio over a crank angle section before and after compression TDC as the representative swirl ratio of the cylinder head intake port according to the change of the engine speed.

• 한국산학기술학회논문지
• /
• 제12권11호
• /
• pp.4718-4725
• /
• 2011

본 연구는 성능 해석을 통하여 1600cc급 흡기매니폴드의 흡기유량 및 분배특성에 대한 연구를 수행하였다. 일차원 엔진 성능해석 프로그램과 3차원 유동해석프로그램을 이용하여 해석을 수행하였다. 흡기 매니폴드의 정상상태 유동해석을 수행한 결과, 일차원 유동해석과 3차원 유동해석의 유량계수 표준편차는 1% 미만으로 우수한 분배특성을 나타내었다. 일차원 해석 결과가 3차원 결과 대비 미소하게 증가된 결과를 보였지만 동등한 유량계수 경향성을 나타냈다. 비정상상태 해석은 분배특성 측면에서 정상상태 해석 결과와 유사한 결과를 보였으며, 정상상태 해석결과를 통한 비정상상태 분배특성의 예측이 가능함을 확인하였다.

• 해양환경안전학회지
• /
• 제25권6호
• /
• pp.788-794
• /
• 2019

최근 지구의 기후변화는 온실가스가 원인으로 전 세계적 대기환경문제로 크게 부각되고 있다. 국내에서도 기후변화에 적극 대응하기 위한 기술개발이 꾸준히 진행되고 있다. 날씨의 이상고온으로 인한 환경에 미치는 영향과 갑작스런 집중호우가 환경에 미치는 영향을 대상으로 하였다. 우리생활 주변 대기온도가 상승하였을 때 온도변화에 의한 대기오염발생에 미치는 영향을 연구하고자 한다. 본 연구의 실험조건은 선박 디젤기관에서 회전수 1400 rpm, 1600 rpm 그리고 1800 rpm, 부하는 0 %에서 25 %씩 100 %까지 하였고, 흡기 온도변화는 20℃에서 50℃까지 구분하여 연구하였다. 연구한 결과 흡기온도가 증가함에 따라 일산화탄소 및 탄화수소는 약간 감소하였으나 연료소비율, 질소산화물, PM은 약간 증가하였다. 또한 연소온도는 큰 변화가 없었다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.7-12
• /
• 2003

The purpose of this work is to investigate the effect of premixing condition on the combustion and exhaust emission characteristics in a HCCI diesel engine. To form homogeneous charge before intake manifold, the premixed fuel is injected into premixed tank by GDI injection system and the premixed fuel is ignited by direct injected diesel fuel. But in the case of high intake air temperature, premixed fuel is auto-ignited before diesel combustion and soot emission is increased. In the case of light load condition, the BSFC is improved by intake air heating because increased air temperature promoted the combustion of premixed mixture. NOx and smoke concentration of exhaust emissions are reduced compared to conventional diesel engine. The combustion characteristics of the HCCI diesel engine such as combustion pressure, rate of heat release, and exhaust emission characteristics are discussed.