• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.157-157
• /
• 2011

박막형태로 제작이 가능한 비정질 실리콘은 결정질 실리콘에 비하여 AM-1 (Air Mass 1:100mW/cm2)조건하에서 10-3 S/cm 정도의 높은 광전기전도도와 가시광선 영역($4000{\sim}7000{\AA}$)에서 약 10배의 높은 광흡수계수를 가지며, $300^{\circ}C$ 이하의 낮은 기판온도에서 다양한 기판위에 대면적으로 제작이 가능할 뿐만 아니라 제작공정이 단순하여 제작비용이 저렴하다는 이점이 있다. 본 실험에서 제작된 모든 박막은 PECVD로 증착하였으며 구조는 p-i-n superstrate형 구조를 사용하였고, 각 박막의 두께는 p-a-Si:H/i-a-SiGe:H/n-a-Si:H ($300{\AA}/2000{\AA}/600{\AA}$)으로 고정하였다. a-Si:H (hydrogenated amorphous silicon) 태양전지의 광 흡수층인 i-layer에서의 germane 가스 유량 변화(0, 20, 40. 60, 80, 100 sccm)에 대한 흡수율의 차이를 UV/Vis/Nir spectrophotometer (ultraviolet/visible/near infrared spectrophotometer)를 통해 확인하고, 그에 따른 a-Si:H 박막 태양전지를 제작하여 solar simulator를 사용하여 AM 1.5 G의 환경 조건에서 태양전지 특성을 평가하였다. 그 결과 germane 가스 유량이 증가함에 따라 파장에 대한 absorptance (a.u.)값이 증가함을 알 수 있었으며, 흡수되는 파장영역의 범위가 장파장으로 확대됨을 확인할 수 있었다. 또한 germane 가스 유량이 60 sccm 일때 a-SiGe:H 박막 태양전지 변환효율이 3.80%로 최대값을 가졌다. 실험에서 germane 가스 유량이 증가할수록 흡수율이 높아져 태양전지특성이 향상될 거라 예상 했지만, 100 sccm보다 60 sccm일 때가 단락전류밀도 값과 변환효율이 높다는 것을 확인할 수 있었다. 이는 각 layer사이에 계면상의 문제가 있을 거라 예상되며 직렬저항측정을 통해 확인할 수 있다.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.114-125
• /
• 1978

The use of petroleum fuels in grain drying causes problems of high cost and management. To solve these problems, it is required to study on soLar energy as an alternative to petroleum fuels for grain drying. The purposes of this study were to find out the optimum received area and air flow rate of a flat-plate solar air collector for grain drying and to assess its effects on grain drying with a small grain bin. The results of this study are summarized as follows ; 1. The calculated optimum tilt angles of the collector in the summer and autumn drying seasons were 20 and 50 degress, respectively, in suwon area. 2. The outlet temperature of the collector was $36^\circ C$ on the daily average with the maximum of $36^\circ C$ at 12:00 o clock. Solar radiation on the collector surface was 1.04 ly( 1 langley = 1 cal/$cm^2$) per minute on the daily average and 1.30 ly per minute on the maximum at 11:00am. The thermal efficiency of the collector was 62.4 percent on the daily average, and the air flow-rate per unit receiving are was 1.03 $m^3$/min/$m^2$.4. The calculated optimum receiving area and the air flow-rate per unit cubic volume for paddy in autumn drying season was 2 $m^2$ and 2$m^3$/min , respectively. 5. not significantly difference in the collector efficiency was appeared between the rotating and fixed type of solar collector. 6. For drying of wheat with 0.6 meter of the depth in the bin, approximately 9 hours were required to reduce the moisture content from 21.6% to 13% with air follow rate of 5 $m^3$/min an initial moisture per cubic meter of wheat and with air temperature of $52^\circ C$. 7. In the drying test of rough rice with a turning operation in a grain bin approximately 21 hours were required to reduced the moisture from 21% to 14.5% with airflow rate of 2 $m^3$/min per cubic meter of rice and the air temperature of $43.5^\circ C$. 8. Over-drying at the bottom and less -drying at the top of the grain mass was resulted from the high -temperature of drying air which was obtained from the flat-plate solar collector in this test. An appropriate operation should be prepared for the uniform moisture of the grain in the bin.

• Korean Journal of Medicinal Crop Science
• /
• v.8 no.2
• /
• pp.123-128
• /
• 2000

This study was carried out to determine factors affecting on the mass propagation of Rehmannia glutinosa seedlings in bioreactor culture. Air-lift type bioreactor was more compatible to shoot formation than stirrer type. Fifty grams(90 stem explants) of inoculum in 1.5L medium was placed into 2.5L bioreactor with aeration rate of 0.5 v.v.m., which was proper for effective shoot formation. Adding MES as pH buffer to culture medium increased the numbers of shoot formation. Adding 5g/l of anti-vitrifying agent into culture medium was highly effective for diminishing the rate of vitrification in shoots formed.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1714-1715
• /
• 2011

In this work, highly conductive organic solvent-based polyaniline(PANI) was used as an anode in organic photovoltaic cells (OPV) based on poly - (3-hexylthiophene) and [6,6] - phenyl - C60 - butyricacid methyl ester (P3HT : PCBM). The transmittance of the used PANI film were 87.67% and 86.57% at 550nm, and its sheet resistance were 454 ${\Omega}/{\Box}$ and 298 ${\Omega}/{\Box}$. We fabricated ITO-free OPV cells using PANI as an anode, which exhibited an external power conversion efficiency of 2.28% with a result of Jsc of 6.922mA/cm2, Voc of 0.6093V, and FF of 54.10% under an illumination of air mass(AM) 1.5G (100mW/$cm^2$). We used ink-jet printing to deposit buffer layer and active layer on a glass substrate.

• Korean Journal of Medicinal Crop Science
• /
• v.8 no.1
• /
• pp.9-13
• /
• 2000

To determine the proper carbon and nitrogen sources and their proper levels for mass micro propagation of Scrophularia buergeriana Miquel, tonic and curing cough experiment were applied and a method for mass cultivation by using bioreactors (2.5 L) was expinined. Proper ratio of $NH_4NO_3\;:\;$KNO_3$ was 413 mg/L : 1900 mg/L for multiple shoot production. Sucrose was more effective than glucose or fractose as carbon source and 3% concentration was good for shoot formation. Total nitrogen was not detected after six weeks both in 500 ml flask and bioreactor culture. Sucrose was decreased sharply after two weeks and there was no sucrose left after three weeks both in 500 ml flask and bioreactor culture. The stirrer in bioreactor caused shear stress to shoots severely. The sphere type bioreactor was better than the cylinder type and removal of inner loop in sphere type was more effective to avoid shear stress.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.197.2-197.2
• /
• 2015

Low-cost, high efficiency solar cells are tremendous interests for the realization of a renewable and clean energy source. ZnTe based solar cells have a possibility of high efficiency with formation of an intermediated energy band structure by impurity doping. In this work, the ZnTe:O/CdS/ZnO structure was fabricated by pulsed laser deposition (PLD) technique. A pulsed (10 Hz) Nd:YAG laser operating at a wavelength of 266 nm was used to produce a plasma plume from an ablated a ZnTe target, whose density of laser energy was 4.5 J/cm2. The base pressure of the chamber was kept at a pressure of approximately $4{\times}10-7Torr$. ZnO thin film with thickness of 100 nm was grown on to ITO/glass, and then CdS and ZnTe:O thin film were grown on ZnO thin film. Thickness of CdS and ZnTe:O were 50 nm and 500 nm, respectively. During deposition of ZnTe:O films, O2 gas was introduced from 1 to 20 mTorr. For fabricating ZnTe:O/CdS/ZnO solar cells, Au metal was deposited on the ITO film and ZnTe:O by thermal evaporation method. From the fabricated ZnTe:O/CdS/ZnO solar cell, current-voltage characteristics was measured by using HP 4156-a semiconductor parameter analyzer. Finally, solar cell performance was measured using an Air Mass 1.5 Global (AM 1.5 G) solar simulator with an irradiation intensity of 100 mW cm-2.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.10
• /
• pp.3052-3058
• /
• 2014

In this article, we have designed and synthesized a novel donor-${\pi}$-acceptor (D-${\pi}$-A) type porphyrin-based sensitizer (denoted UI-5), in which a carboxyl anchoring group and a 9,9-dimethyl fluorene were introduced at the meso-positions of porphyrin ring via phenylethynyl and ethynyl bridging units, respectively. Long alkoxy chains in ortho-positions of the phenyls were supposed to reduce the degree of dye aggregation, which tends to affect electron injection yield in a photovoltaic cell. The cyclic voltammetry was employed to determine the band gap of UI-5 to be 1.41 eV based on the HOMO and LUMO energy levels, which were estimated by the onset oxidation and reduction potentials. The incident monochromatic photon-to-current conversion efficiency of the UI-5 DSSC assembled with double-layer (20 nm-sized $TiO_2$/400 nm-sized $TiO_2$) film electrodes appeared lower upon overall ranges of the excitation wavelengths, but exhibited a higher value over the NIR ranges (${\lambda}$ = 650-700 nm) compared to the common reference sensitizer N719. The UI-5-sensitized cell yielded a relatively poor device performance with an overall conversion efficiency of 0.74% with a short circuit photocurrent density of $3.05mA/cm^2$, an open circuit voltage of 0.54 mV and a fill factor of 0.44 under the standard global air mass (AM 1.5) solar conditions. However, our report about the synthesis and the photovoltaic characteristics of a porphyrin-based sensitizer in a D-${\pi}$-A structure demonstrated a significant complex relationship between the sensitizer structure and the cell performance.

• Applied Chemistry for Engineering
• /
• v.22 no.1
• /
• pp.15-20
• /
• 2011

Poly[2,3-dimethyl-5,8-dithiophene-2-yl-quinoxaline-alt-9,9-dihexyl-9H-fluorene] (PFTQT) and poly[2,3-dimethyl-5,8-dithiophen-2-yl-quinoxaline-alt-10-hexyl-10H-phenothiazine (PPTTQT) based on 2,3-dimethyl-5,8-dithiophen-2-yl-quinoxaline weresynthesized by Suzuki coupling reaction. All polymers were soluble in common organic solvents such as chloroform, chlorobenzene, o-dichlorobenzene, tetrahydrofuran (THF) and toluene. The maximum absorption wavelength and band gap of PFTQT were 440 nm and 2.30 eV, and PPTTQT were 445 nm and 2.23 eV, respectively. The HOMO and LUMO energy level of PFTQT were -6.05 and -3.75 eV, and PPTTQT were -5,89 and -3.66 eV, respectively. The organic photovoltaic devices based on the blend of polymer and PCBM (1 : 2 by weight ratio) were fabricated. Efficiencies of devices were 0.24% (PFTQT) and 0.16% (PPTTQT), respectively. The short circuit current density ($J_{sc}$), fill factor (FF), and open circuit voltage ($V_{oc}$) of the device with PFTQT were $0.97mA/cm^2$, 29% and 0.86 V, and the device based on PPTTQT were $0.80mA/cm^2$, 28% and 0.71 V, 31% and 0.71 V, respectively, under air mass (AM) 1.5 G and 1 sun condition ($100mA/cm^2$).