• Journal of the Korean Chemical Society
• /
• v.61 no.4
• /
• pp.191-196
• /
• 2017

One-phase method to prevent the initial formation of Ag(I) thiolate layered materal from the mixture of $AgNO_3$ and thiols was previously developed to generate TP (Thiolate-Protected)-nanosilver. In this modified method, $AgNO_3$ is added to the mixtures of $NaBH_4$ and thiols in ethanol. This method was so successful that it was applied to synthesize TP-nanogold and nanoplatinum. The synthesis and characterization of these nanoparticles by ultraviolet-visible (UV-vis) absorption spectra, transmission electron microscopy (TEM) pictures, X-ray powder differaction (XRD) patterns and infrared(IR) spectra are described. The results show that colloidal nanoparticles are spherical or oval shape and the mean sizes for TP-nanogold and nanoplatinum are about 3~7 nm and below 2 nm, respectively. The conformation of polymethylene [$-(CH_2)_7-$] sequence in octanethiolate attached to nanogold was elucidated as trans.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.130-133
• /
• 2001

A multifilamentary Bi-2223 HTS tape for superconducting power applications was studied through the fabrication of 250-meter long tapes by the PIT(powder in tube) process. To fabricate continuous long wire, a drawing machine, a two-drum bull block and a rolled tape winding machine were developed. Especially, 250-meter long tapes were heat treated in the shape of pancake coil to reduce the heat affect zone and to achieve the high critical current. Engineering critical current density was improved through both the enhancements of critical current density by control of thermal process and the increase of filling factor by using thin Ag alloy sheath tubes less than 1.5 mm in thickness. We have made successfully 250-meter long 37 filamentary tapes with high filling factor up to 31 % employing the modified drawing and rolling technique. The critical current of 250-meter long tapes with pancake coil type was measured by transport method at self-field up to 250 gauss of center field. The measured values, based on the transport critical current at self-field, $I_{c}$ -B characteristics and magnetic field analysis, are 34 A of I$_{c}$ and 4.0 $kA/\textrm{cm}^2$ of $J_{e}$ at 250 m, 77 K, and 0 T. We also have achieved the 56 A of I$_{c}$ and 7.0 $0 kA/\textrm{cm}^2$ of$ J_{e}$ in short tapes at 77K, self-field, and 1$mutextrm{V}$/cm.

• Journal of Conservation Science
• /
• v.33 no.5
• /
• pp.355-362
• /
• 2017

The Nongso tomb of Sunchang was built in a relatively deep place; hence there was little damage from grave robbers. The tomb was completely filled with a large amount of charcoal, and therefore the wooden coffin was excavated in relatively good condition. On the basis of the structure of the tombs, excavated artifacts, and radiocarbon dating results, the tomb is estimated to be from between the late Goryeo and the early Joseon period. The wooden coffin excavated is double-layered structures consisting of an outer coffin and an inner coffin. The outside of the wooden coffin is thickly lacquered and decorated with yellow letters and white motifs. An analysis of the pigments' components revealed that the major component of the letters was gold (Au) and the major component of the motifs was silver (Ag). The coffin lacquer had three layers: a pigment layer, a yellowish-brown layer, and a black layer. The wooden bases of the coffins were painted with a black substance, such as soot, as mineral elements were not detected in the black layer. The yellowish-brown layer is presumed to be refined lacquer. From the analysis of the structure of the layers and pigments, we can estimate the method was adopted for making lacquer for wooden coffin. It is assumed that the method used gold leaf and gold powder. The form of the pigment and the internal structure are likely to be gold leaf, but the shape of the surface letters appears to have been formed using gold powder. This study will serve as important information for understanding lacquer making techniques at the time of the tombs' construction by confirming the making method through reproduction experiments using gold leaf and gold powder.

• Archives of design research
• /
• v.18 no.4 s.62
• /
• pp.35-44
• /
• 2005

In the world, most of the metal technologists were as called as adornment artists than other field of industrial arts strongly industrial characters functional materials and manufacturing technology many used in the present age. In the study, one of adornments researched and material character analyzed about Art Clay Silver. The shrinkage rate of shape was about 0.24%. A shrinking phenomenon drying time thought of evaporation of water linking bonding agents and powders. After calcination of Art Clay Silver, the EDX used that just Ag 100% analyzed a result from the surface assay in the room temperature. A binder with powder in the room temperature considered to disappear, because it was been fume and smoke at high calcined temperature. A study showed when handicrafted necklaces make by these characteristic as using in difficult and delicated operations rather than naturally and beautifully expressive products.

• Carbon letters
• /
• v.4 no.4
• /
• pp.168-174
• /
• 2003

Silver nitrate ($AgNO_3$) powder was mixed into a reformed pitch precursor. Then, the silver-containing pitch was melt spun to form round and "C" shape fibers. A wire mesh was inserted prior to the nozzle to improve the spinnability of the silvercontaining precursor pitch. Silver particles in the carbon fibers (CFs) were detected by XRD and TEM. These tests showed that silver particles were uniformly distributed and the total amount of silver remained constant during stabilization and carbonization. Next, the silver-containing CFs were activated by steam diluted in nitrogen gas. Silver particles accelerated the activation rate, but the specific surface areas of the silver-containing ACFs were similar to those of non-silver containing ACFs at the same burn-off levels. The specific surface area of the C-shaped activated carbon fibers was larger than that of the round activated carbon fibers. The likely reason is that the surface area of a C-shaped CF is about two times larger than that of a round CF when equivalent cross-sectional areas are compared. A small amount of silver particles in the periphery of the CFs was removed during the activation, but the remainder of silver was stayed within the ACFs.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.04a
• /
• pp.9-10
• /
• 2000

An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.