• Analytical Science and Technology
• /
• v.17 no.5
• /
• pp.381-387
• /
• 2004

To characterize chemically a spent pressurized water reactor (PWR) fuel, an analytical method for trace amounts of tritium ($^3H$) in it has been established. Considering the effective management of radioactive wastes generated through the whole experimental process and the radiological safety for analysts, a separation condition under which $^{14}C$ and $^3H$ can be sequentially recovered from a single fuel sample was optimized using simulated spent PWR fuel dissolved solutions. $^{14}CO_2$ evolved during dissolution of the spent PWR fuels with nitric acid was trapped in an aliquot of 1.5 M NaOH. $^{129}I_2$ which was volatilized along with $^{14}CO_2$ was removed using a silver nitrate-impregnated silica gel absorbent. $^3H$ remaining in the fuel dissolved solution as $^3H_2O$ was selectively recovered by distillation. Its recovery yield was 97.9% with a relative standard deviation of 0.9% (n=3). $^3H$ in a spent PWR fuel with burnup value of 37,000 MWd/MtU was analyzed, reliability of this analytical method being evaluated by standard addition method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.105-112
• /
• 2018

This paper proposes a method for fabricating heatable glass using the conduction characteristics of metal thin films deposited on the surface of Low-e(Low emissivity) glass. The heating value of Low-e glass depends on the Joule heat caused by Low-e glass sheet resistance. Hence, its prediction and design are possible by measuring the sheet resistance of the material. In this study, silver electrodes were placed at 50 mm intervals on a soft Low-e glass sample with a low emissivity layer of 11 nm. This study measured the sheet resistance using a 4-point probe, predicted the power consumption and heating value of the Low-e glass, and confirmed the heating performance through fabrication and experience. There are two conventional methods for manufacturing heatable glass. One is a method of inserting nichrome heating wire into normal glass, and the other is a method of depositing a conductive transparent thin film on normal glass. The method of inserting nichrome heating wire is excellent in terms of the heating performance, but it damages the transparency of the glass. The method for depositing a conductive transparent thin film is good in terms of transparency, but its practicality is low because of its complicated process. This paper proposes a method for manufacturing heatable glass with the desired heating performance using Low-e glass, which is used mainly to improve the insulation performance of a building. That is by emitting a laser beam to the conductive metal film coated on the entire surface of the Low-e glass. The proposed method is superior in terms of transparency to the conventional method of inserting nichrome heating wire, and the manufacturing process is simpler than the method of depositing a conductive transparent thin film. In addition, the heat characteristics were compared according to the patterning of the surface thin film of the Low-e glass by an emitting laser and the laser output conditions suitable for Low-e glass.

• Journal of Conservation Science
• /
• v.31 no.4
• /
• pp.361-372
• /
• 2015

The experiment attempts to find out the effect of the mixture of the antimicrobial agent and insecticide on metallic material including Silver(99.9%), Copper(99.9%), Lead(99.9%) and Iron(99.5%) by Oddy test. The mixtures of the antimicrobial agent and insecticide were prepared in 60ml; with the standard concentration of 17.5% in B77 Essential oil mixture, one for mixture of concentration of ${\pm}1{\sim}2%$ and insect repellent material; the other for mixture of low concentration and antimicrobial agent(BS-2 and BS-3) material. After Oddy test, we investigated the variation in the surface of the samples by visual inspection, weighing, color measurement and SEM-EDS analysis. The result showed that Lead had the biggest change in the surface, and Copper had the biggest change in the color. In addition, changes in the samples before and after the experiment were found to be greatest at concentration of 19% of Essential oil mixture of the antimicrobial agent and insecticide. Also, B78 Essential oil mixture produce change in samples. It means when the concentration of oil mixture rises, the variation of the samples gets bigger. And, the low concentration of mixture including B77 Essential oil mixture and B78 Essential oil mixture also produce big change in the samples. However, the low concentration of B77 Essential oil mixture that do not contain B78 Essential oil mixture was able to confirm that the change of the surface is not large.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.334-341
• /
• 2016

In this paper, the study of a waveguide aperture-coupled feed-structured antenna has been conducted for the purpose of applying it to a wireless back-haul system sufficient for high-capacity gigabits-per-second data rates. For this study, a $32{\times}32$ waveguide slot sub-array antenna with a corporate-feed structure was designed and produced. Also, this antenna is used at 57 GHz to 66 GHz in the V-band. The construction of the antenna is a laminated form with radiating parts (outer groove and slot, cavity), a coupled aperture, and feeds in each. The antenna was designed with HFSS, which is based on 3D-FEM, produced with aluminum processed by a precision-controlled milling machine, and assembled after a silver-plating process. The measurement result from analysis of the characteristics of the antenna shows that return loss is less than -12 dB, VSWR < 2.0, and a wide bandwidth ranges up to 16%. An overall first side lobe level is less than -12.3 dB, and a 3 dB beam width is narrow at about $1.85^{\circ}$. Also, antenna gain is 38.5 dBi, offering high efficiency exceeding 90%.

• Economic and Environmental Geology
• /
• v.30 no.1
• /
• pp.61-65
• /
• 1997

Cadmium occurs as a minor element in sphalerite ((Zn, Fe)S) from the Boseong-Jangheung gold-silver mine district. We analyzed the abundance of cadmium in sphalerite using an electron probe micro analyzer (EPMA) and discussed the natural sources of cadmium in terms of bedrock geochemistry, in order to preliminarily reconnoiter the potential cadmium contamination in mine districts. Cadmium contents of sphalerites from the Au-Ag mines (Bodeok, Mundeok, Jeonbo, Boknae, Keumsan) in the Boseong-Jangheung district are considerably high, compared with cadmium contents of sphalerites (average = 0.5 wt.% Cd, maximum = 4.4 wt.% Cd) in the world. Sphalerites from the Keumsan mine (average = 9.49 wt.% Cd, maximum=11.22 wt. Cd) are highly enriched in cadmium. Our data suggest that the Boseong-Jangheung area is an important potential site of cadmium contamination in Korea. Based on bedrock geochemistry, natural causes of cadmium enrichment in sphalerite from the mine district are thought to be the mixing of cadmium leached from organic-rich, metasedimentary rocks (including coal) and/or black shales. From this study, we propose that the pinpointing of potential sites of pollution by toxic heavy metals can be done effectively through detailed reconnaisance study on mineralogical compositions of ore minerals such as sphalerite from the mine area.

• Journal of the Korean Society of Safety
• /
• v.32 no.2
• /
• pp.34-37
• /
• 2017

In recent emerging industry, Display field becomes bigger and bigger, and also semiconductor technology becomes high density integration. In Flat Panel Display, there is an issue that electrostatic phenomenon results in fine dust adsorption as electrostatic capacity increases due to bigger size. Destruction of high integrated circuit and pattern deterioration occur in semiconductor and this causes the problem of weakening of thermal resistance. In order to solve this sort of electrostatic failure in this process, Soft X-ray ionizer is mainly used. Soft X-ray Ionizer does not only generate electrical noise and minute particle but also is efficient to remove electrostatic as it has a wide range of ionization. X-ray Generating efficiency has an effect on soft X-ray Ionizer affects neutralizing performance. There exist variable factors such as type of anode, thickness, tube voltage etc., and it takes a lot of time and financial resource to find optimal performance by manufacturing with actual X-ray tube source. MCNPX (Monte Carlo N-Particle Extended) is used for simulation to solve this kind of problem, and optimum efficiency of X-ray generation is anticipated. In this study, X-ray generation efficiency was measured according to target material thickness using MCNPX under the conditions that tube voltage is 5 keV, 10 keV, 15 keV and the target Material is Tungsten(W), Gold(Au), Silver(Ag). At the result, Gold(Au) shows optimum efficiency. In Tube voltage 5 keV, optimal target thickness is $0.05{\mu}m$ and Largest energy of Light flux appears $2.22{\times}10^8$ x-ray flux. In Tube voltage 10 keV, optimal target Thickness is $0.18{\mu}m$ and Largest energy of Light flux appears $1.97{\times}10^9$ x-ray flux. In Tube voltage 15 keV, optimal target Thickness is $0.29{\mu}m$ and Largest energy of Light flux appears $4.59{\times}10^9$ x-ray flux.

• Economic and Environmental Geology
• /
• v.29 no.1
• /
• pp.45-55
• /
• 1996

Although the Dongjin Au-Ag-Cu mine had been abandoned since about forty years ago, the results of this study on the dispersion patterns and contamination level of heavy metals in the hydrologic system flowing via the waste rump show that the environmental impacts from the mine wastes are still significant. The stream water in the vicinity of the waste rump is severely acidified (pH 3.8 to 4.4) and highly enriched in various dissolved heavy metals. The heavy metal contents of the stream water and stream sediments are systematically attenuated with increasing distance from the mine area. However, it is worth to note that continuous attenuation of heavy metal contents in both media were reenriched in downstream area more than 800 m apart from the mine because it can be acted as a secondary source of heavy metal pollution. The heavy metals, especially Cd, Cu and Zn of polluted downstream sediments mainly occur in Fe-Mn oxides and organic materials, which indicates that these elements are the main pollutants from the waste rump of the Dongjin mine. The heavy metal contents of crops, such as sesame, perilla, red Pepper and brown rice, collected from the polluted farm land in the downstream area are lower than those of land plants from stream sides, but significantly higher in Cd, Cr, Cu and Zn than those from the unpolluted farm land. Especially, almost all of the crops in polluted farm land have been severly contaminated by Cd (>0.4 ppm). On the other hand, the heavy metal contents of the crops collected from refreshed farm land by means of a soil addition method shows significantly lowered level comparing with those of polluted area, which indicates that a soil addition method was effective for the refreshment of polluted farm land by toxic metallic pollutants. Wormwoods from this area showed very high contents in a11 the heavy metals even in unpolluted area (Cd > 1 ppm, Cr > 1 ppm, Cu > 11 ppm, Pb> 4 ppm, Zn > 55 ppm), indicating that a special caution must be payed when one takes ingest them.

• Applied Biological Chemistry
• /
• v.12
• /
• pp.25-31
• /
• 1969

The characteristics of crude enzyme produced from Trichoderma viride($O_2-1$) which isolated from half spoiled Locust acacia wood (Robinia Pseudacacia Linne) were examined in this paper. The results obtained were summarized as follows: 1) As a results of enzymatic action on several cellulose substrate it was found that there were some sorts of cellulase in crude enzyme. 2) The activity of C.M.C. ase and ${\beta}-glucosidase$ were decreased in accordance with increasing concentration of substrate, and filter paper saccharifying enzyme relatively increased in accordance with increasing concentration of substrate and enzyme in couse of time. 3) The optimal pH of each enzyme was 5.0 and the range of stability on pH generally from 3 to 6. 4) In disintegrating activity on filter paper, in decomposing activity on C.M.C. and $p-nitrophenyl-{\beta}-D-glucoside$, and in saccharifying activity on filter paper, the optimal temperatures were $50^{\circ}C.,\;60^{\circ}C,\;and\;65^{\circ}C$. 5) The order of stability on temperature was as follow; saccharifying activity on filter paper decomposing activity on C.M.C. disintegrating activity on filter paper>decomposing activity on $p-nitrophenyl-{\beta}-D-glucoside$. 6) The activity of the enzymes was inhibited with mercuric and silver ion, and activated with potassium.

• Economic and Environmental Geology
• /
• v.42 no.4
• /
• pp.301-314
• /
• 2009

The Taebaeksan mineralized province, which is the most important one in South Korea, is rich in zinc-lead-tungsten-iron-copper-molybdenum-silver-gold mineral resources and has a diversity of deposit styles. These deposits principally coexist in time and space with porphyry-related epigenetic deposit such as skarn, hydrothermal replacement, mesothermal vein, and Carlin-like deposits. The magmatic-hydrothermal systems in the Taebaek fold belt is genetically characterized by the Bulguksa subvolcanic rocks(ca. $110{\sim}50\;Ma$) related to northwestward subduction of the paleo-Pacific Plate. The most important zinc-lead deposits in the area are the Uljin, Yeonhwa II and Shinyemi skarn, the Janggun hydrothermal replacement, and the Yeonhwa I intermediate-mixed (skarn/hydrothermal replacement) ones. In the present study, we present a compilation of metal production and mineral assemblage of the zinc-lead deposits. The metal difference of deposit styles in the area indicates a cooling path from intermediate-sulfidation to low-sulfidation state in the polymetallic hydrothermal system, reflecting spatial proximity to a magmatic source.

• Economic and Environmental Geology
• /
• v.46 no.2
• /
• pp.153-163
• /
• 2013

The Ogcheon Au-Ag deposit consists of two quartz veins that fill the NE or NW-trending fissures in the metasedimentary rocks of unknown age. The quartz veins occur mainly in the massive type with partially breccia and cavity. They can be found along the strike for about minimum 50 m and varied in thickness from 0.1 to 0.3 m. The mineralogy of quartz veins from the Ogcheon deposit is mainly composed of hydrothermal alteration minerals such as pyrite, quartz, sericite, chlorite, clay minerals and sulfides including pyrite, pyrrhotite, arsenopyrite, sphalerite, chalcopyrite and galena. Fluid inclusion data from quartz indicate that homogenization temperatures and salinity of mineralization range from 184 to $362^{\circ}C$ and from 0.0 to 6.6 wt.% eq. NaCl, respectively. These suggest that ore forming fluids were progressively cooled and diluted from mixing with meteoric water. Sulfur(${\delta}^{34}S$: 0.4~8.4‰) isotope composition indicates that ore sulfur was derived from mainly magmatic source although there is a partial derivation from the host rocks. The calculated oxygen(${\delta}^{18}O$: 4.9~12.1‰) and hydrogen(${\delta}D$: -92~-74‰) isotope compositions suggest that magmatic and meteoric ore fluids were equally important for the formation of the Ogcheon deposit and then overlapped to some degree with another type of meteoric water during mineralization.