• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2003년도 기술심포지움 논문집
• /
• pp.151-155
• /
• 2003

The requirements for harsh environment electronic controllers in automotive applications have been steadily becoming more and more stringent. Electronic substrate technologists have been responding to this challenge effectively in an effort to meet the performance, reliability and cost requirements. An effect of the plasma cleaning at the alumina substrate and the IMC layer between $Sn-37wt\%Pb$ solder and Ag-Pd thick film conductor after reflow soldering has been studied. Organic residual carbon layer was removed by the substrate plasma cleaning. So the interfacial adhesive strength was enhanced. As a result of AFM measurement, Ag-Pd conductor pad roughness were increased from 304nm to 330nm. $Cu_6Sn_5$ formed during initial ref]ow process at the interface between TiWN/Cu UBM and solder grew by the succeeding reflow process so the grains had a large diameter and dense interval. A cellular-shaped $Ag_3Sn$ was observed at the interface between Ag-Pd conductor pad and solder. The diameters of the $Ag_3Sn$ grains ranged from about $0.1\~0.6{\mu}m$. And a needle-shaped $Ag_3Sn$ was also observed at the inside of the solder.

• 마이크로전자및패키징학회지
• /
• 제11권1호
• /
• pp.1-6
• /
• 2004

자동차 전장품의 시험환경 조건이 엄격해짐에 따라, 전장품 개발 기술자들은 이에 부합하는 성능, 신뢰성, 비용 등을 고려한 보다 효과적인 제품 설계를 위해 노력하고 있다. 본 논문에서는 ECM 알루미나 기판의 플라즈마 세척 영향과 리플로우 후 Sn-37wt%Pb 솔더와 패드 접합부 계면에서 형성되는 금속간 화합물을 관찰하였다. 기판의 플라즈마 세척은 계면 접착력을 저해하였던 C에 의한 유기 잔류물 층이 제거되어 계면 접착력을 향상시키는 효과가 있다. 또한 AFM 분석 결과 도체 패드의 표면 거칠기는 304 nm에서 330 m로 증가하였다. 리플로우 과정에서 솔더와 TiWN/Cu 패드 계면에서 형성된 $Cu_6/Sn_5$는 리플로우 횟수가 증가할 수록 결정립의 크기도 조대화되었다. 솔더와 Ag-Pd 도체패드 계면에서는 세포질 형태의 $Ag_3Sn$화합물이 관찰되었다. $Ag_3Sn$은 지름이 약 0.1∼0.6 $\mu\textrm{m}$이며, 솔더 내부에서는 침상 모양도 관찰되었다.

• 한국세라믹학회지
• /
• 제25권6호
• /
• pp.623-630
• /
• 1988

As a function of the composition and content of frit, the electrical property of Ag and Ag/Pd thick film conductors were investigated with microstructure. With increasing sintering temperature in Ag-frit thick film conductors, electrical sheet resistivity decreased, but again increased above 80$0^{\circ}C$. And when frit contents is 5wt%, compact and homogenious microstructure can be obtained, then electrical sheet resistivity has minimum value. In Ag/Pd-frit film conductor, the electrical sheet resistivity decreased with increasing sintering temperature. The system which having frit with low softing point has lower sheet resistivity then to add high softening point frit.

• 한국전기전자재료학회논문지
• /
• 제17권12호
• /
• pp.1352-1355
• /
• 2004

We have applied front contact metallization of plated nickel and copper for high efficiency passivated emitter rear contact(PERC) solar cell. Ni is shown to be a suitable barrier to Cu diffusion as well as desirable contact metal to silicon. The plating technique is a preferred method for commercial solar cell fabrication because it is a room temperature process with high growth rates and good morphology. In this system, the electroless plated Ni is utilized as the contact to silicon and the plated Cu serves as the primary conductor layer instead of traditional solution that are based on Ti/Pd/Ag contact system. Experimental results are shown for over 20 % PERC cells with the Plated Ni/Cu contact system for good performance at low cost.