• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.307-310
• /
• 2008

Nonlinear Vortex Strength Correction Method is developed for improvement of vortex lattice method which can't calculate the separated flow conditions and the viscous effect. In this method, the vortex strength on the blade surface is determined by matching the lift force from vortex lattice method with the lift force from aerodynamic coefficients table as the same circulation is added to or subtracted from all chord wise vortices. For considering the nonlinearities due to the neighboring blade sections, sophisticated Newton-Rapson algorithm is applied. The validation of this method was done by comparing the simulations with the measurements on the NREL Phase-VI horizontal axis wind turbine(HAWT) in the NASA Ames wind tunnel under uniform conditions. This method gives good agreements with experiments in most cases.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.445-452
• /
• 1998

The dynamic performance design of catenary-pantograph system which collects current for the next generation Korean high speed train(KHST) was considered. Used was the same dynamic model of the catenary-pantograph system as that of TGV-K which will be introduced for Kyung-bu corridor. Using the model , sensitivity analysis fer design variables were made to improve dynamic performance of KHST system. The results of sensitivity analysis and performance improvement are as follows: (1) It was found that aerodynamic force, tension of contact wire, mass of contact strip, mass of supporting contact strip, mass of clamp, mass of steady arm, and stiffness of plunger were the design variables most influencing the dynamic performance of the system. (2) Pantograph with reductions of 20% aerodynamic force, 34% weight of supporting contact strip, 20% spring constant of plunger, and 34% equivalent mass of steady arm was very possible system for the KHST which will be running at maximum operating speed 350 km/h.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1998년도 제10회 학술강연회논문집
• /
• pp.21-21
• /
• 1998

추력방향 제어시스템 설계에 있어서 가장 기본적으로 요구되는 Requirement는 Rocket Motor의 추력, 요구되는 최대 Side Force, Rocket Motor의 외경, System의 총 구동시간, 구동후의 분리여부 등이다. 이러한 Requirement를 만족하기 위해서는 Nozzle 출구의 분출가스 물성치로부터 초음속 유동해석을 통하여 Vane 주위의 속도, 온도, 압력 분포를 구하고, Vane의 받음각 변화에 대한 Aerodynamic Force와 Moment를 계산하고, Side Force를 만족하는 최대 받음각의 결정, Torque를 만족하는 감속기와 Motor의 선정 및 Housing 기본 형상을 설계하였다. 금번 개발에서는 지상 시험용으로서 안전 계수를 Flight Model보다 약간 높게 설계하였으며, 작동 완료 후 System이 Nozzle로부터 떨어져나가는 분리시스템은 포함하지 않았다.

• 한국항공우주학회지
• /
• 제34권11호
• /
• pp.18-25
• /
• 2006

비정상 공기력 측정이 두 쌍의 날개를 갖는 잠자리 유형 모델의 위상차에 따른 효과를 조사하기 위하여 수행되었다. 잠자리 유형 모델의 플런징 운동에 의하여 발생된 공기역학적인 힘을 측정하기 위하여 로드셀을 사용하였다. 본 잠자리 유형 모델은 실제 잠자리와 동역학적으로 상사하며, 앞뒤날개는 각각 0°의 10°의 붙임각(incidence angle)을 가지고 있다. 다른 실험 조건은 다음과 같다. 자유류의 속도는 1.6 m/sec이고, 이와 관련된 시위 레이놀즈수 2.88×103이며, 앞뒤날개의 위상차는 각각 0°, 90°, 180°, 그리고 270°이다. 잠자리 유형 날개의 한 주기 동안 공기역학적 계수의 변화가 제시되었다. 연구 결과는 잠자리 유형 모델의 양력은 앞뒤날개가 downstroke 운동을 수행할 때 발생되며, 뒷날개가 downstroke 운동과정을 수행하면 양력 발생과 함께 항력도 발생한다는 것을 보여준다.

• Wind and Structures
• /
• 제20권3호
• /
• pp.449-468
• /
• 2015

Current wind-resistance designs of large-scale indirect dry cooling towers (IDCTs) exclude an important factor: the influence of the ventilation rate for radiator shutter on wind loads on the outer surfaces of the tower shell. More seemingly overlooked aspects are the effects of various ventilation rates on the wind pressure distribution on the tower surfaces of two IDCTs, and the feature of the flow field around them. In order to investigate the effects of the radiator shutter ventilation rates on the aerodynamic interference between IDCTs, this paper established the numerical wind tunnel model based on the Computational Fluid Dynamic (CFD) technology, and analyzed the influences of various radiator shutter ventilation rates on the aerodynamic loads acting upon a single and two extra-large IDCTs during building, installation, and operation stages. Through the comparison with the results of physical wind tunnel test and different design codes, the results indicated that: the influence of the ventilation rate on the flow field and shape coefficients on the outer surface of a single IDCT is weak, and the curve of mean shape coefficients is close to the reference curve provided by the current design code. In a two-tower combination, the ventilation rate significantly affects the downwind surface of the front tower and the upwind surface of the back tower, and the larger positive pressure shifts down along the upwind surface of the back tower as the ventilation rate increases. The ventilation rate significantly influences the drag force coefficient of the back tower in a two-tower combination, the drag force coefficient increases with the ventilation rate and reaches the maximum in a building status of full ventilation, and the maximum drag coefficient is 11% greater than that with complete closure.

• 한국전산유체공학회지
• /
• 제19권2호
• /
• pp.66-71
• /
• 2014

Aerodynamic design of a vehicle has very important meaning on the fuel economy, dynamic stability and the noise & vibration of a moving vehicle. In this study, the correlation of aerodynamic effect between two model vehicles moving inline on a road was studied with the basic SAE model vehicle. Drag and lift are two main physical forces acting on the vehicle and both of them directly effect on the fuel economy and driving stability of the vehicle. For the research, the distance between two vehicles is varied from 5m to 30m at the fixed vehicle speed, 100km/h and the side-wind was assumed to be zero. The main issue for this numerical research is on the understanding of the interaction forces; lift and drag between two vehicles formed inline. From the study, it was found that as the distance between two vehicles is closer, the drag force acting on both the front and rear vehicle decreases and the lift force has same trend for both vehicle. As the distance(D) is 5m, the drag of the front vehicle reduced 7.4% but 28.5% for the rear-side vehicle. As the distance is 30m, the drag of the rear vehicle is still reduced to 22% compared to the single driving.

• International Journal of Aeronautical and Space Sciences
• /
• 제18권1호
• /
• pp.8-16
• /
• 2017

Most of small air vehicles with moving wing fly at low Reynolds number condition and the reduced frequency of the moving wing ranges from 0.0 to 1.0. The physical phenomena over the wing dramatically vary with the reduced frequency. This study examines experimentally the effect of the reduced frequency at low Reynolds number. The NACA0012 airfoil performs sinusoidal pitching motion with respect to the quarter chord with the four reduced frequencies of 0.1, 0.2, 0.4 and 0.76 at the Reynolds number $2.3{\times}10^4$. Smoke-wire flow visualization, unsteady surface pressure measurement, and unsteady force calculation are conducted. At the reduced frequency of 0.1 and 0.2, various boundary layer events such as reverse flow, discrete vortices, separation and reattachment change the amplitude and the rotation direction of the unsteady force hysteresis. However, the boundary layer events abruptly disappear at the reduced frequency of 0.4 and 0.76. Especially at the reduced frequency of 0.76, the local variation of the unsteady force with respect to the angle of attack completely vanishes. These results lead us to the conclusion that the unsteady aerodynamic characteristics of the reduced frequency of 0.2 and 0.4 are clearly distinguishable and the unsteady aerodynamic characteristics below the reduced frequency of 0.2 are governed by the boundary layer events.

• Wind and Structures
• /
• 제32권5호
• /
• pp.471-485
• /
• 2021

Onshore wind turbines may experience substantially different wind loads depending on their working conditions, i.e. rotation velocity of rotor blades, incoming freestream wind velocity, pitch angle of rotor blades, and yaw angle of the wind-turbine tower. In the present study, aerodynamic loads acting on a horizontal axis wind turbine were accordingly quantified for the high tip speed ratio (TSR) at high yaw angles because these conditions have previously not been adequately addressed. This was analyzed experimentally on a small-scale wind-turbine model in a boundary layer wind tunnel. The wind-tunnel simulation of the neutrally stratified atmospheric boundary layer (ABL) developing above a flat terrain was generated using the Counihan approach. The ABL was simulated to achieve the conditions of a wind-turbine model operating in similar inflow conditions to those of a prototype wind turbine situated in the lower atmosphere, which is another important aspect of the present work. The ABL and wind-turbine simulation length scale factors were the same (S=300) in order to satisfy the Jensen similarity criterion. Aerodynamic loads experienced by the wind-turbine model subjected to the ABL simulation were studied based on the high frequency force balance (HFFB) measurements. Emphasis was put on the thrust force and the bending moment because these two load components have previously proven to be dominant compared to other load components. The results indicate several important findings. The loads were substantially higher for TSR=10 compared to TSR=5.6. In these conditions, a considerable load reduction was achieved by pitching the rotor blades. For the blade pitch angle at 90°, the loads were ten times lower than the loads of the rotating wind-turbine model. For the blade pitch angle at 12°, the loads were at 50% of the rotating wind-turbine model. The loads were reduced by up to 40% through the yawing of the wind-turbine model, which was observed both for the rotating and the parked wind-turbine model.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.647-652
• /
• 2016

To reduce drag force at supersonic speeds, sharp leading edge is hugely efficient. It is, however, incompatible with leading edge shape to have fine aerodynamic characteristics at subsonic and transonic speeds. It is critical to reduce drag force for enhanced cruise performance and higher efficiency. An air superiority fighter, however, required to have high maneuverability for survivability, and sharp leading edge is not proper. Consequently, variable leading edge is demanded to reduce drag force significantly at supersonic speeds for cruise performance. Leading edge altering system is constructed with rigid material to improve possibility of realization, and minimized movement of its components in altering for reduce effects on flight. It is compared with bi-convex airfoil and NACA 65-006 airfoil, which have comparable maximum thickness. At Mach number 1.7 and zero angle of attack, supersonic mode of designed airfoil indicates approximately 17% higher drag coefficient than the bi-convex airfoil indicates, it is, however, 23% lower than the NACA 65-006 indicates. Also, subsonic mode of the designed airfoil shows fine aerodynamic characteristics in comparison with NACA 65-006 airfoil in subsonic and transonic speed range. In this regard, design of the airfoil achieved the object of this study satisfactorily.

• 대한기계학회논문집A
• /
• 제38권2호
• /
• pp.115-120
• /
• 2014

본 연구에서는 다물체 동역학 해석 소프트웨어인 RecurDyn 을 이용하여 풍력 발전기를 쉽게 모델링하고 동적 거동 해석을 수행할 수 있는 기법을 개발하였다. 풍력 발전기는 타워, 너셀, 허브, 그리고 블레이드로 구성되어 있다. 타워와 블레이드는 탄성체로 가정하였고 탄성효과를 고려하기 위하여 탄성체 이론을 이용하여 모델링 하였다. 바람의 속도는 일정하다고 가정하였고 날개 요소 운동량 이론을 이용하여 공력하중을 모델링 하였다. 이를 통해 계산된 공력을 풍력 발전기에 적용시키고 동적 거동 해석을 수행하였다. 해석의 타당성을 검증하기 위하여 풍력 발전 시스템 상용 소프트웨어인 GH-Bladed를 이용한 해석결과와 비교하였다.