• Journal of the Korea Institute of Military Science and Technology
• /
• v.25 no.1
• /
• pp.9-22
• /
• 2022

A fighter performing a reconnaissance mission is equipped with a pod that drives optical/infrared sensors for acquiring and identifying target information on the lower part of the fuselage. Due to the nature of the reconnaissance mission, the fighter performs high speed evasive maneuvers, and the resulting load should be considered importantly for the development of the pod. This paper concerns a numerical investigation into the inertial and aerodynamic loads of the airborne pod of high performance aircrafts. For the aerodynamic load analysis, the pylon and pod shapes are added to the fighter 3D model, and the commercial software was used for static and dynamic analysis. Considering the practical mission conditions, the common/extreme conditions were established respectively in the static and dynamic situations of pods and the driving torque could be tripled under dynamic conditions. In the analysis of inertia load, a 3-DOF model considering roll and turning maneuvers was derived by the Lagrangian method, and then the numerical integration method was applied to the analysis. As a results, it was conformed that the inertia load was generally induced at a low level compared to the aerodynamic load, but depending on the unbalance mass condition of the pod, the inertia load cannot be negligible.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.2
• /
• pp.85-93
• /
• 2021

In this paper, the aerodynamic characteristics of general tail controlled missile were predicted and corrected the result using semi-empirical analysis tool. The cause of the error was confirmed by comparing the aerodynamic characteristics prediction result of the semi-empirical analysis tool with the wind tunnel test result, and the main error factor of the semi-empirical analysis tool was the interference component between the main wing and the tail wing. The semi-empirical analysis results were corrected using the wind tunnel test results and the computational analysis results, and it was confirmed that the corrected data agrees well with the wind tunnel test results. Through this study, it was confirmed that the wing-tail interference component correction is needed when predicting the aerodynamic characteristics of a general tail controlled missile using a semi-empirical analysis tool.

• Structural Engineering and Mechanics
• /
• v.56 no.6
• /
• pp.1021-1040
• /
• 2015

An effective method to calculate aerodynamic loads and aeroelastic responses of large wind turbine tower-blade coupled structures in yaw condition is proposed. By a case study on a 5 MW large wind turbine, the finite element model of the wind turbine tower-blade coupled structure is established to obtain the modal information. The harmonic superposition method and modified blade-element momentum theory are used to calculate aerodynamic loads in yaw condition, in which the wind shear, tower shadow, tower-blade modal and aerodynamic interactions, and rotational effects are fully taken into account. The mode superposition method is used to calculate kinetic equation of wind turbine tower-blade coupled structure in time domain. The induced velocity and dynamic loads are updated through iterative loop, and the aeroelastic responses of large wind turbine tower-blade coupled system are then obtained. For completeness, the yaw effect and aeroelastic effect on aerodynamic loads and wind-induced responses are discussed in detail based on the calculating results.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.35-41
• /
• 2010

The temperature of the flight objects in high speed increases due to the aerodynamic heating. MINIVER and CFD approach are used to predict the aerodynamic heating conditions of KSLV-I. MINIVER is based on the empirical method. And the CFD approach predicts the aerodynamic heating conditions after the analysis of the surface temperature and the surface heat flux directly. In this study, the aerodynamic heating conditions using CFD approach are considered. The PLF temperature for these aerodynamic heating conditions is compared with the flight test data of KSLV-I.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.6-15
• /
• 2008

This paper deals with the aeroelastic instability of vibrating multiple blade rows under aerodynamic coupling with each other. A model composed of three blade rows, e.g., rotor-stator-rotor, where blades of the two rotor cascades are simultaneously vibrating, is considered. The displacement of a blade vibrating under aerodynamic force is expanded in a modal series with the natural mode shape functions, and the modal amplitudes are treated as the generalized coordinates. The generalized mass matrix and the generalized stiffness matrix are formulated on the basis of the finite element concept. The generalized aerodynamic force on a vibrating blade consists of the component induced by the motion of the blade itself and those induced not only by vibrations of other blades of the same cascade but also vibrations of blades in another cascade. To evaluate the aerodynamic forces, the unsteady lifting surface theory for the model of three blade rows is applied. The so-called k method is applied to determine the critical flutter conditions. A numerical study has been conducted. The flutter boundaries are compared with those for a single blade row. It is shown that the effect of the aerodynamic blade row coupling substantially modifies the critical flutter conditions.

• Journal of computational fluids engineering
• /
• v.13 no.2
• /
• pp.1-7
• /
• 2008

For Aerodynamic analysis of vehicle at altitude, 100km, the validity of governing equations based on continuum model, was reviewed. Also, as the preliminary study for the sub-orbital space plane development, a candidate geometry was suggested and computational fluid dynamic(CFD) analysis was performed for various angles of attack in subsonic and supersonic flow regimes to analyze the aerodynamic characteristics and performance. The inviscid flow analyses showed that the stall starts at angle of attack above $20^{\circ}$, the maximum drag is generated at angle of attack, $87^{\circ}$ and the maximum lift to drag ratio is about 8 in subsonic flow. In supersonic, the stall angle is about $40^{\circ}$ and the maximum drag is generated at angle of attack, $90^{\circ}$. Also, mach number distribution of re-entry vehicle was computed versus altitudes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.3
• /
• pp.244-252
• /
• 2012

Recently, the speed of a train has been increased. So the trains are being exposed to wind more severely than before. Because of the operation of high speed trains and lightweight of the train, risks of train derailment have being increased. In this study, aerodynamic effects of a newly designed high speed train, HEMU-400x, are evaluated. For aerodynamic effect evaluation, analysis method is selected by examining the safety standards for high speed train. The condition of aerodynamic effects is selected by adverse effect conditions. In order to calculate $C_s$ coefficients, numerical analysis is conducted. Using $C_s$ coefficients, the side force is calculated. Through dynamics analysis, derailment and wheel unloading are obtained. Using these results, derailment evaluation is performed.

• Journal of computational fluids engineering
• /
• v.17 no.2
• /
• pp.28-34
• /
• 2012

In this study, the reliability-based design optimization of the airfoil was performed. PARSEC function was used to consider the uncertainty of the aerodynamic shape for the reliability-based shape optimization of airfoils. Among various reliability analysis methods, the moment method was used to compute the probability of failure of the aerodynamic performance. The accuracy of the reliability analysis was compared with other methods and it was found that the moment method predicts the probability of failure accurately. Deterministic and reliability-based optimizations were performed for the shape of the airfoil and it was demonstrated that reliability-based optimum assures the aerodynamic performances under uncertainties of the shape of the airfoil.

• Structural Monitoring and Maintenance
• /
• v.4 no.2
• /
• pp.175-194
• /
• 2017

Research to date has mainly focused on structural analysis and design of wind turbines considering turbulent aerodynamic loading. The combined effects of wind and seismic loading have not been studied by many researchers. With the recent expansion of wind turbines into seismically active regions research is now needed into the implications of seismic loading coupled with turbulent aerodynamic loading. This paper proposes a monitoring procedure for onshore horizontal axis wind turbines (HAWTs) subjected to this combined loading regime. The paper examines the impact of seismic loading on the 5-MW baseline HAWT developed by the National Renewable Energy Laboratory (NREL). A modified version of FAST, an open-source program developed by NREL, is used to perform the dynamic analysis.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.1308-1311
• /
• 1996

We propose a new linearized model which can be used very efficiently for the design and analysis of the autopilot of aerodynamically controlled skid-to-turn missiles. Proposed model is based on the linearized equations of the missile dynamics derived in the aerodynamic frame where xz plane contains the missile longitudinal axis and velocity vector. However, to take the effect due to the small perturbation of the missile body into consideration, we introduce a new frame which is identical to the aerodynamic frame in the trim state but after small perturbation it moves fixed with the missile body, and finally, the proposed model is set up in this frame. It is shown by nonlinear simulations and stability analysis of a numerical example that the new model describes the missile motion better than the conventional one linearized in the body frame with a certain amount of simplification.