• 한국수소및신에너지학회논문집
• /
• 제32권4호
• /
• pp.197-204
• /
• 2021

Pressure swing adsorption is a purification process which can get pure hydrogen. The purification process is composed of four process: compression, adsorption, desorption and discharge. In this study the adsorption process was simulated by using the Fluent and validated with experimental results. A gas used in experiment is composed of H₂, CO₂, CH₄, and CO. Adsorption process conducted under 313 kelvin and 3 bar and bituminous-coal-based (BPL) activated carbon was used as the adsorbent. Langmuir model was applied to explain the gas adsorption. And diffusion of all the gases was controlled by micro-pore resistances. The result shows that, the most adsorbed gas was carbon dioxide, followed by methane and carbon monoxide. And carbon monoxide took the least amount of time to reach the maximum adsorption amount. The molar fraction of the off-gas became the same as the molar fraction of the gas supplied from the inlet after adsorption reached the equilibrium.

• 한국물환경학회지
• /
• 제27권4호
• /
• pp.516-522
• /
• 2011

This study was performed to investigate the removal characteristics of phosphate by adsorption on olivine, which is generated as industrial by-products from quarry. The adsorption of phosphate on olivine was significantly achieved within 1 hour and equilibrated after 3 hours. The adsorption capacity of phosphate was enhanced with decreasing pH. The maximum adsorption capacity was observed to be 0.463 mg/g in the condition of pH 3. The $Ca^{2+}$ and $Mg^{2+}$ ion amount per adsorbent eluted from olivine was increased with decreasing pH. The precipitation test showed that phosphate in aqueous phase under the condition of pH 3 ~ 9 could be eliminated largely by adsorption on olivine, not precipitation. Freundlich adsorption model were successfully applied to describe the adsorption behavior of phosphate on olivine. The $q_m$ of Langmuir adsorption model were 1.3369 mg/g, 1.0544 mg/g, 1.0288 mg/g at pH 3, 6 and 9, respectively. The $K_F$ of Freundlich adsorption model were 0.4247 mg/g, 0.3399 mg/g, 0.2942 mg/g at pH 3, 6 and 9, respectively. The olivine showed high feasibility as a adsorbent for the removal of $PO_4$-P.

• 한국환경과학회지
• /
• 제32권8호
• /
• pp.563-572
• /
• 2023

Scoria from Jeju-island (Jeju scoria) was converted into zeolitic material (Z-SA) via zeolitification using the fusion/hydrothermal method. Jeju scoria could be synthesized into Z-SA to from a surface covered with Na-A zeolite crystals, which was confirmed through an analysis of X-ray diffraction peak patterns and scanning electron microscopy images. Jeju scoria and Z-SA were employed as adsorbents to evaluate the adsorption rate and adsorption capacities for Cu²⁺ and Zn²⁺ ions. The adsorption rates and isothermal adsorption capacities could be well fitted by the pseudo-quadratic adsorption kinetics and Langmuir adsorption isotherm, respectively. The maximum adsorption capacities (q_m) of Z-SA for Cu²⁺ and Zn²⁺ ions were found to be 163.36 mg/g and 120.51 mg/g, respectively, using the Langmuir adsorption isotherm. When Z-SA is synthesized from Jeju scoria via zeolitification using the fusion/hydrothermal method, Z-SA exhibits an adsorption capacity that is more than approximately 100 times the value exhibited by Jeju scoria. As a result, the synthesized Z-SA was regarded as an effective, economic adsorbent.

• 한국환경보건학회지
• /
• 제37권1호
• /
• pp.50-56
• /
• 2011

The adsorption capacity of charcoal is a function of the airborne concentration of the target chemical. To evaluate the adsorption capacity of charcoal packed in the cartridges of air purifying respirators, breakthrough tests were conducted with carbon tetrachloride for three commercial cartridges (3M models #7251, #6000 and AX) at 25, 50, 100, 250 and 500 ppm. Adsorption capacities were calculated using a mass transfer balance equation derived from the curve fitting to the breakthrough curves obtained experimentally. Carbon micropore volumes were estimated by iteration to fit the Dubinin/Radushkevich (D/R) adsorption isotherm. They were 0.6566, 0.5727 and 0.3087 g/cc for #7251, #6000 and the AX cartridge, respectively. Above 100 ppm (at high challenge concentrations), #7251 and #6000 showed higher adsorption capacities. However, as the challenge concentration decreased, the adsorption capacities of #7251 and #6000 sharply dropped. On the other hand, the adsorption capacity of the AX cartridge showed little change with the decrease of the challenge concentration. Thus, the AX showed a higher adsorption capacity than #7251 and #6000 at the 5-50 ppm level. It is concluded that service-life tests of cartridges and adsorption capacity tests of charcoal should be conducted at challenge concentration levels reflecting actual working environmental conditions. Alternatively, it is recommended to use the D/R adsorption isotherm to extrapolate adsorption capacity at low concentration levels from the high concentration levels at which breakthrough tests are conducted, at a minimum of two different concentration levels.

• 한국세라믹학회지
• /
• 제56권2호
• /
• pp.146-152
• /
• 2019

In order to study the transport behavior of tripolyphosphate (TPP) in aqueous solutions, the adsorption process of TPP on synthetic goethite, which exists stably in supergene environment, has been systematically studied. The adsorption properties under different conditions (pH, electrolyte presence, and temperature) were investigated. The adsorption of TPP in the presence of humic acid (HA)/fulvic acid (FA) has also been discussed in this paper. The results indicated that the adsorption capacity quickly increased within the first hour and equilibrium was reached within 24 h. The adsorption capacity decreased from 1.98 to 0.27 mg·g^-1 upon increasing the pH from 8.5 to 11.0, whereas the adsorption of TPP on goethite hardly changed with increasing electrolyte concentration. The results of analysis of the kinetic and isothermal models showed that the adsorption was more in accord with the pseudo second-order equation and Freundlich model. The adsorption capacity decreased obviously regardless of the order of addition of TPP, HA, and goethite. Subsequent addition of FA led to a large increase in the adsorption capacity, which might be attributed to the adsorption ability of FA. According to the predictions of the kinetic and isothermal models and the spectroscopic evidence (X-ray diffraction (XRD), Fourier Transform infrared spectroscopy (FT-IR), and scanning electron microscope (SEM)), the adsorption mechanism may be mainly based on surface complexation and physical adsorption.

• 폴리머
• /
• 제26권5호
• /
• pp.551-558
• /
• 2002

술폰산형 섬유이온교환체를 이용하여 도금 폐수 중 니켈 이온 분리를 위해 각각의 조건에 따른 니켈 이온에 대한 흡착 특성을 관찰하였다. 술폰산형 섬유이온교환체의 함수율은 술폰화도 극성이 클수록 크게 나타났으며 이온교환용량은 술폰화도가 증가함에 따라 증가하였으며 술폰화도 16%에서 3.38 meq/g로 높게 나타났다. 니켈이온의 흡착은 pH 변화에 따라 크게 변화하지 않았고 모든 흡착은 10분 이내에 약 7.5 mg/min의 흡착속도로 매우 빠르게 평형에 도달하였다. 재생 시 흡착용량은 7회까지 3.15 meq/g으로 거의 100% 가까이 탈착되었으며 그 이상에서는 2.01 meq/g으로 약간 감소하는 것으로 보아 본 연구에 사용한 이온교환체는 내구성에 문제가 없는 것으로 판단되었다. 한편 흡착평형 시간은 L/D의 값이 증가함에 따라 선형적으로 증가하였으며, 최대 흡착용량은 각각 2.71∼3.01 meq/g으로 약간 증가하였고 L/D의 변화에 크게 영향이 없는 것으로 보아 L/D<2로 흡착칼럼의 설계가 가능할 것으로 사료되었다. 또한 이온교환 섬유의 충전비가 일정할 때 pH 변화에 따른 니켈 이온의 흡착량은 산성 pH에서는 큰 변화가 없는 것으로 보아 도금수세액의 pH가 산성인 점을 고려할 때 pH 5 이하가 적합한 것으로 판단되었다.

• KSBB Journal
• /
• 제11권2호
• /
• pp.218-224
• /
• 1996

The adsorption of cellulase on celluloses with different crystallinities was carried out In nonionic surfactant(Tween 20) solution. Highly crystallized celluloses were prepared by enzymatic prehydrolyzation. From the experiments, the Langmuir isotherm parameters, maximum adsorption amount (Amax) and adsorption equilibrium constant(Kad) for the adsorption, were obtained in the presence and absence of nonionic surfactant. It was found that the Kad values were decreased by adding Tween 20. This indicates that the adsorption affinity is reduced by nonionic surfactant, and Amax decreased with increasing crystallinity under conditions accompanying in both the presence and absence of surfactant. The thermodynamic parameters such as $\Delta$Ha, $\Delta$Ga, and $\Delta$Sa for the adsorption were calculated by using the experimental data. From these results, it was found that the adsorption processes are exothermic reactions in both the presence and absence of surfactant. The heats of adsorption in surfactant solution(-4.68∼-3.62KJmol-1) are smaller than that of the adsorption in the absence of surfactant(-15.60∼-12.10KJmol-1). These results indicated that the tightness of adsorption was reduced by the addition of surfactant. The $\Delta$Sa values were estimated to be positive. This may suggest that the water and solute are released from cellulose on adsorption. The $\Delta$Sa values in surfactant solution are larger than that of the adsorption in the absence of surfactant. This may suggest that the binding of surfactant on hydrophobic region of cellulase cause dispersion of water and solute molecule orienting around the enzyme molecule. The surfactant played an important role in the desorption of enzyme from cellulose functional groups, and enhance the saccharification of the cellulose.

• 한국산업보건학회지
• /
• 제24권2호
• /
• pp.193-200
• /
• 2014

Objectives: To develop domestic charcoal tubes with good adsorption capacity, breakthrough experiments were performed on four types of activated charcoal. Materials: The adsorption capacity and the adsorption rate were determined using a modified Wheeler equation after the breakthrough experiment. For four types of charcoal (J, K, S and SKC Inc. 226-01), 100 mg were used in the breakthrough experiment. The test was done on benzene, toluene, n-hexane, and acetone in a dynamic chamber. Results: K charcoal had the greatest surface area and the highest micropore volume. J charcoal had a similar surface area and micropore volume to SKC charcoal. S charcoal had the lowest surface area and micropore volume. J charcoal had the highest adsorption capacity at 101, 252 and 609 ppm of benzene. The gap in benzene adsorption capacity among the types of charcoal was the least at 609 ppm and the greatest at 101 ppm. J charcoal showed the highest adsorption capacity at 54, 106, 228 and 508 ppm of toluene. J charcoal and SKC charcoal had a similar adsorption capacity for acetone. J charcoal had the highest adsorption capacity for n-hexane. In the experiment featuring 10% breakthrough volume, 10% breakthrough occurred at 18 liters at $2065.9mg/m^3$ for J charcoal and at 20 liters at $1771.2mg/m^3$ for K charcoal. It was difficult to judge adsorption capacity by surface area and micropore volume of charcoal. J charcoal, which was similar to SKC charcoal in surface area and micropore volume, showed good adsorption capacity at common workplace concentrations. Conclusions: The adsorption capacity of J and K charcoal was superior compared with SKC charcoal. J and K charcoal can be considered appropriate for use as sampling media based on this result.

• 분석과학
• /
• 제5권1호
• /
• pp.1-5
• /
• 1992

Amberlite XAD 고분자수지 및 고분자수지 대체흡착제인 rice bran, rice straw 그리고 sawdust에 대한 petroleum oil의 흡착량을 최저 흡착조건에서 뱃치법으로 측정하여 조사하였다. Rice bran과 rice straw에 대한 petroleum oil의 흡착량은 XAD계열수지의 흡착량의 약 50% 정도로 흡착성이 우수하였다. 또한 이들 대체흡착제의 흡착능을 증대시키기 위한 탄화시간은 $200^{\circ}C$, 30분이 최적 조건이었다. Sawdust의 경우에는 30% MeOH 매질에서는 흡착성이 매우 약한 반면 0.5M NaCl 매질에서는 XAD수지 흡착능이 약 1/2에 도달하였다. Rice bran과 rice straw는 외관상의 구조차이와는 관계없이 비슷한 흡착능력을 보였다. 따라서 rice bran과 rice straw들은 XAD계열 수지에 대한 대체흡착제로 충분한 흡착능력을 가지고 있는 것으로 보인다.

• 상하수도학회지
• /
• 제26권3호
• /
• pp.431-442
• /
• 2012

The purpose of this study, is to separate magnetic separation devices using permanent magnets by using magnetization characteristics remaining in treated water after adsorption and synthesizing phosphorus adsorbent capable of magnetic separation for efficient removal of phosphorus. The synthesis of the adsorbent which set Zirconium(Zr) having high friendly features for phosphorus as an element, and by synthesizing Iron Oxide($Fe_3O_4$, another name of $Fe_3O_4$ is magnetite) being able to grant magnetism to Zirconium Sulfate($Zr(SO_4)_2$), zirconium magnetic adsorbent(ZM) were manufactured. In order to consider the phosphorus adsorption characteristics of adsorbent ZM, batch adsorption experiment was performed, and based on the results, pH effect, adsorption isotherm, adsorption kinetics, and magnetic separation have been explore. As the experiment result, adsorbent ZM showed a tendency that the adsorption number was decreased rapidly at pH 13; however, it was showed a high amount of phosphorus removal in other range and it showed the highest amount of phosphorus removal in pH 6 of neutral range. In addtion, the Langmuir adsorption isotherm model is matched well, and D-R adsorption isotherm model is ranged 14.43kJ/mol indicating ion exchange mechanism. The result shown adsorption kinetics match well to the Pseudo-second-order kinetic model. The adsorbent ZM's capablility of regenerating NaOH and $H_2SO_4$, was high selectivity on the phosphorus without impacts on the other anions. The results of applying the treated water after adsorption of phosphorus to the magnetic separation device by using permanent magnets, shows that capture of the adsorbent by the magnetization filter was perfect. And they show the possibility of utilization on the phosphorus removal in water.