• Korea-Australia Rheology Journal
• /
• v.19 no.2
• /
• pp.51-59
• /
• 2007

A polyelectrolyte chain confined in a slit nanochannel exhibits a structural transition from the one in free space. In this paper, the effect of the long-range electrostatic interactions between the xanthan polyelectrolyte and the slit wall on the confined xanthan conformation is investigated via the Brownian dynamics simulation. A neutral and two negatively charged surfaces of polydimethylsiloxane (PDMS) and glass are combined to make four kinds of slit channels with different charge characteristics: i) neutral-neutral, ii) glass-glass, iii) neutral-PDMS and iv) neutral-glass walls. Their walls are characterized by uniform surface charge densities determined from experimental data of zeta potential. Both the nonmonotonic chain size variation and the loss of long-range bond vector correlation, previously observed under confinement in the PDMS-PDMS slit, are also found in the neutral slit, demonstrating the nonelectrostatic origin of such crossover behaviors. As expected, the effect of wall charges is negligible at sufficiently high medium ionic strength of 100mM but it becomes significant in the opposite limit of 0.01mM. In the latter case, the high charge density of glass walls strengthens the effective confinement of a negatively charged polyelectrolyte and produces a xanthan structure comparable to that confined in a much narrower neutral slit. The obtained structural data suggest the possibility of controlling the structure of confined polyelectrolytes by the modification of surface charge characteristics of micro/nanofluidic devices in combination with the adjustment of the medium ionic strength.

• Fire Science and Engineering
• /
• v.23 no.5
• /
• pp.125-132
• /
• 2009

In this study we could contribute to the development of a precise checking tool with which the reliability of the automatic fire detection systems was enhanced and the safety of the people was ensured. In the same way as the domestic technical standard, the portable smoke sensitivity tester, which was developed in this work, could be used to check the capability of the smoke detectors installed in the field. Its heater inside was warmed up to $400^{\circ}C$ in 40 seconds and the paper as a smoke source was burned to produce smoke for the test. With the Photoelectric smoke detector it was possible to measure and control the smoke concentration in a range from 0%/m to 25%/m. With the adjustment of rpm of the fan, it was possible to keep a constant wind velocity in a range from 20cm/sec to 40cm/sec.

• Journal of Korean Society for Geospatial Information Science
• /
• v.3 no.2 s.6
• /
• pp.159-172
• /
• 1995

This study aims to apply digital photogrammetric methods on the close range photogrammetry. To get a three dimensional position with digital photogrammetric method, scanning, image matching, and bundle adjustment are performed. Comparing the three dimensional position computed by digital photogrammetric methods with ground survey values, the errors can be detected. Analyzing the errors, it is possible to present a new digital photogrammetric method for the close range photogrammetry. Image matching method used in this study is area-based pixel unit and subpixel unit method. As a result of the study, three dimensional position error is 3.32mm and the error in the single coordinate axis direction is 0.76mm in pixel unit and in subpixel unit, respective error is 3.98mm and 0.73mm.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.18 no.3 s.39
• /
• pp.23-37
• /
• 1990

The purpose of this study was to suggest, an ameliorated, 'standard of estimated unit manpower & material' in the Landscape Planting Work. To achieve this goal of this study, following process was performed to reach more advanced results. First, relevant domestic & foreign references were gathered & analyzed with a viewpoint of the system & contents within, Second, most similar foreign country‘s relevant 10 forms & actual site were surveyed, Third, actual site data were collected from the 17 selected landscape Planting sites Fourth, the collected data from reference study & actual site survey were analyzed and calculated. And Finally, analyzed data were reorganized & rearranged in good order with 3 principles to produce more ameliorated 'Standard of estimated unit manpower & material' in the landscape Planting Work. The suggested main results of this study include, 1. Reorganization of current system to transplanting(includes excavation & root ball wrapping), planting(includes tree & shrub), turfing & maintenance 2. Deletion of the Range of 'account of labor' & simultaneous distribution of 'account of labor' with a proposed regular ratio 3. Adjustment of the range of the plant's size 4. Amelioration of the level of 'Account of labor' 5. New establishment in maintenance items as Watering, Fertilizing & spraying chemicals on turf area. 6. Readjustment & new establishment of the backfill volume. 7. Actualization, readjustment & new establishment of the transportation amount.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.8B
• /
• pp.904-909
• /
• 2011

Cell zooming adjusts the cell range of base stations depending on traffic condition. The cell zooming can be implemented by the adjustment of antenna angles, the clustering of the base stations, and the cell relay. The base stations can adjust the cell range in term of energy efficiency, which can then reduce the overall energy consumption of cellular networks. There is, however, a trade-off between the energy savings and the blocking probability of user calls. A periodic scheme that manages the cell zooming of the base stations was proposed but it was inadequate for dealing with the dynamic nature of traffic patterns. This paper proposes a semi-periodic cell zooming scheme along with the algorithms that select such base stations and define the operation procedure. Simulation results show that the proposed method outperforms the existing scheme in terms of the energy savings without the degradation of the blocking probability.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.785-792
• /
• 2019

In parallel operation of multiple power converter modules, equal power distribution among modules shall be made to improve the reliability of the system. In this paper, a novel droop method is proposed to present improved current distribution characteristics. In the proposed method, if the current in each module become greater than the current set-point value, the output voltage set-point is raised to improve the current distribution characteristics. Meanwhile, when the output voltage is to be managed within the tolerance range, the range of the usable control IC reference value ($v_{ref}$) will be reduced if the output voltage setting is always raised. Thus, in case the output voltage set-point among modules is reversed, the downward adjustment is introduced. The proposed method was experimentally validated with a 17.5V/500mA prototype of two boost converters operating in parallel.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.6
• /
• pp.67-76
• /
• 2007

Raining method has been widely used for preparing sand specimen because of its ability to reconstitute the homogeneous specimen with desired relative density and its reliability established by the numerous experiments on diverse influential factors. In conventional raining methods, adjustment of relative density is achieved by controlling the shutter porosity and the whole system is required to be re-adjusted to achieve the target relative density when the granular characteristics are changed. It is also observed from conventional methods that certain degrees of spatial variation in density exist and the limited range of relative density is reproduced. In this paper, raining system with porous plate is proposed. It is shown that the wide range of relative density can be achieved by controlling failing height only. This enhanced system is able to obviate the subtle control of shutter porosity and minimize the effect of falling distance, which in turn ensures the homogeneity of the specimen, especially for low relative density.

• Geomechanics and Engineering
• /
• v.29 no.5
• /
• pp.509-522
• /
• 2022

Tail-grouting is an effective measure in shield engineering for filling the gap at the shield tail to reduce ground deformation. However, the gap-filling ratio affects the value of the gap parameters, leading to different surface settlements. It is impossible to adjust the fill ratio indiscriminately to study its effect, because the allowable adjustment range of the grouting quantity is limited to ensure construction site safety. In this study, taking the shield tunnel section between Chaoyanggang Station and Shilihe Station of Beijing Metro Line 17 as an example, the correlation between the tail-grouting parameter and the surface settlement is investigated and the optimal grouting quantity is evaluated. This site is suitable for conducting field tests to reduce the tail-grouting quantity of shield tunneling over a large range. In addition, the shield tunneling under different grouting parameters was simulated. Furthermore, we analyzed the evolution law of the surface settlement under different grouting parameters and obtained the difference in the settlement parameters for each construction stage. The results obtained indicate that the characteristics of the grout affect the development of the surface settlement. Therefore, reducing the setting time or increasing the initial strength of the grout could effectively suppress the development of surface subsidence. As the fill ratio decreases, the loose zone of the soil above the tunnel expands, and the soil deformation is easily transmitted to the surface. Meanwhile, owing to insufficient grout support, the lateral pressure on the tunnel segments is significantly reduced, and the segment moves considerably after being removed from the shield tail.

• Journal of Powder Materials
• /
• v.15 no.5
• /
• pp.411-421
• /
• 2008

Principles and historical background of high pressure liquid jet (HPLJ) technology is presented in the paper. This technology can be applied, among others, for production of nano particles. This target can be achieved in various type of disintegration systems developed and designed on the base of this technology. The paper describes principles of two examples of such systems: HPLJ-reactor, called also a linear comminuting system, HPLJ- centrifugal comminuting system, which prototypes have been manufactured. A linear mill, being high energy liquid jet reactor, has been developed and tested for micronization of various types of materials. The results achieved so far, and presented in the paper, show its potential for further improvement toward nano-size particle production. Flexibility of adjustment of the reactors and the mechanism of the process allows for the creation of particles with unprecedented rheology. The reactor can be especially suitable to micronize, mix and densify materials with a wide range of mechanical properties for various industrial needs. Presented prototypes of comminution systems generate interesting potentials toward production of nano particles. Their performance, based on up today research, confirms expected high efficiency of materials disintegration, which opens a new challenge for industrial applications. The paper points out benefits and area of possible applications of presented technology.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.15-26
• /
• 2004

The calibration for systematic error in LiDAR is crucial for the accuracy of airborne laser scanning. The main error is the misalignment of platforms between INS(Inertial Navigation System) and Laser scanner For planimetrical calibration of LiDAR, the building is good feature which has great changes in height and continuous flat area in the top. The planimetry error(pitch, roll) is corrected by adjustment of height which is calculated from comparing ground control points(GCP) of building to laser scanning data. We can know scale correction of laser range by the comparison of LiDAR data and GCP is arranged at the end of scan angle where maximize the height error. The area for scale calibration have to be large flat and have almost same elevation. At 1000m for average flying height, The Accuracy of laser scanning data using LiDAR is within 110cm in height and ${\pm}$50cm in planmetry so we can use laser scanning data for generating 3D terrain surface, expecically digital surface model(DSM) which is difficult to measure by aerial photogrammetry in forest, coast, urban area of high buildings