• Elastomers and Composites
• /
• v.34 no.3
• /
• pp.253-261
• /
• 1999

The cure properties of rubber compounds containing different adhesive compositions were examined. As the amounts of tannin were increased in the adhesive composition, the scorch time was increased and cure rate was decreased due to the size and shape of tannin molecules. Also, the effect of adhesive composition on the adhesion between rubber and fiber was examined by TCAT(Tire Cord Adhesion Test), The reinforcing cords used in this study were mon ofilaments of nylon 610 and nylon 66. According to the results, the optimum adhesion strength between rubber and fiber could be obtained with adhesives whose molar ratios of formaldehyde/resorcinol were above 5/1 in the recipes. Although the level of dip pick-up(DPU) on the reinforcing cord affects the adhesion strength, the DPU of nylon 610 monofilament did not affect the adhesion strength because the level of DPU was constant regardless of the adhesive compositions. In this case, the adhesion strength with the adhesive composition could be explained with the behavior of tannin in the adhesive.

• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.55-59
• /
• 2018

In this study, to overcome a complicated shoe adhesion process such as buffing, pre-treatment by primer in the rubber component of the shoe, we studied adhesion mechanical properties with rubber compound added water-soluble salt for the purpose of improving the adhesion between midsole and outsole. Acid salts, basic salt and neutral salts were evaluated, rubber containing basic salts showed excellent adhesion to water-based adhesion. Since the basic salt is present as the hydroxy salt, the surface of rubber is hydrophilized. The results are confirmed by contact angle and IR spectroscopy measurement. In addition, in the case of rubber compound added basic salts, NBS abrasion resistance and hardness were increased by increasing crosslink density, but crosslink time was delayed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.23 no.4
• /
• pp.92-97
• /
• 2019

A study was conducted to improve the adhesion of propellant, liner,and insulation. Insulation was shown to be more advantageous in improving the adhesion when a barrier coat was applied compared to a bare insulation layer. It was confirmed that the adhesion strength between the insulation and the propellant improves as the thickness of the liner coating increases. The liner was cured for 24 h. If the liner is cured for a long time, it will adversely affect adhesion. Adhesion is also improved when a bonding agent is applied. As the bonding agent content increases, the adhesion improves. There is a change in the adhesive strength depending on the type of bonding agent used. HX-868 shows slightly more improved adhesion than HX-752.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.36 no.11
• /
• pp.1237-1245
• /
• 2012

The effect of hydrophilicity and hydrophobicity of PET fabric on the detergency of particulate soil were investigated as functions of the concentration of hydrophilic and hydrophobic chemicals, surfactant concentration, ionic strength, adhesion and removal time, and pH. The detergency of the particulate soil was determined by the adhesion of particles to and their removal from fabric, the PET fabric and ${\alpha}-Fe_2O_3$ were used as textile materials and for the model of particulate soil, respectively. The hydrophilic and hydrophobic finish for PET fabric was treated with a polyester, silicone and fluorine organic compound of resin respectively. The adhesion of particulate soil to fabric treated with hydrophobic chemicals were slightly higher but its removal from fabric treated with hydrophobic chemicals was largely higher than fabric treated with a hydrophilic chemical regardless of solution conditions such as the concentration of hydrophilic and hydrophobic chemicals, surfactant concentration, ionic strength, adhesion and removal time, and pH. Therefore, hydrophobic treatment for fabric had a more positive effect than the hydrophilic treatment on the detergency of particulate soil.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1030-1035
• /
• 2003

The nanoimprint lithography technology makes higher density of semiconductor device and larger capacity of storage media. In this technology the induced damage while detaching polymer pattern from mold should be minimized. In order to analyze the problem, the basic knowledge of adhesion between the polymer and the mold is required. In this study a contact experiment of polyisobutylene specimen with spherical steel tip and polyisobutylene bead tip was conducted using nano indenter. During the contact experiment with various loading rate under load control the contact behavior of viscoelastic material was measured, i.e., the load and displacement between the tip and the specimen were measured. The data was analyzed by HBK model to obtain the stress intensity factor of contact edge and the contact radius as a function of time. Also the adhesion energies between steel/polyisobutylene and polyisobutylene/polyisobutylene were obtained employing the analysis of the crack of viscoelastic material by Schapery.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.2
• /
• pp.149-157
• /
• 2003

The purpose of this paper is to quantitatively investigate aging state of epoxy coating on containment structure at nuclear power plant. In order to evaluate an physical bonding of the epoxy coating, adhesion test was performed on a degraded epoxy coating on concrete specimens fabricated by accelerated aging experiment. In addition, impedance data by ultrasonic test were measured to compare with adhesion data. From almost 50 % of the specimens, aging phenomena of epoxy coating such as pin hole, blistering was discovered. To improve reliability on quality degradation of epoxy, co-relation between two kinds of different data was analyzed. By tracing co-related these data, it was possible to figure out physical state of as-built epoxy coating. The possibility to develop new methodology of time - dependent aging state on epoxy coating was found and discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.10
• /
• pp.805-811
• /
• 2000

Reliability of PBGA(plastic ball grid array) package is weak compared with normal plastic packages. The low reliability is caused by low resistance to the popcorn cracking, which is generated by moisture absorption in PCB(prited circuit board). In this paper, plasma treatment process was used and we analyzed its effects to interface adhesion. The contents of C and Cl decrease after plasma treatment but those of O, Ca, N relatively increase. The plasma treatment improves the adhesion between EMC(epoxy molding compound) and PCB(solder mask). The grade of improvement was over 100% Max, which depends on the properties of EMC. The RMS(root mean square) roughness value of the solder mask surface increases to plasma treatment. There is little difference of adhesion in RF power and treatment time.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.2
• /
• pp.188-192
• /
• 2007

In this work, the effects of chemical treatment of polyimide films were studied by FT-IR, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and contact angles. The adhesion characteristics of the films were also investigated in the peel strengths of polyimide/aluminum films. The increases of surface functional groups of KOH-treated polyimide films were greatly correlated with the polar component of surface free energy. The peel strength of polyimides to metal substrate was also greatly enhanced by increasing the KOH treatment time, which can be attributed to the formation of polar functional groups on the polyimide surfaces, resulting in enhancement of the work of adhesion between polymer film and metal plate.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.136-137
• /
• 2007

Wear resistant TiAlN thin film has been widely deposited on the surface of cutting and forming tools by using Arc Ion Plating. TiAlN films are deposited by the processes designed by the Taguchi L18 experimental design. The L18 experimental design is applied to achieve surface properties and adhesion. The deposition parameters are working pressure, substrate temperature, bias voltage, arc power and pre-sputtering bias voltage and time. The most influential parameters on surface properties and adhesion are substrate bias voltage, working nitrogen pressure and arc power. The optimal coating processes are obtained for surface properties and adhesion.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.4
• /
• pp.241-250
• /
• 2000

Popcorn cracking phenomena frequently occur in thin plastic packages during the solder reflow process, which are definitely affected by poor adhesion of Cu-based leadframe to epoxy molding compounds (EMCs). In the present work, in order to enhance the adhesion strength, a brown-oxide treatment on the Cu-based leadframe was carried out and the adhesion strength of leadframe/EMC interface was measured in terms of fracture toughness by using sandwiched double-cantilever beam (SDCB) specimens. After the adhesion tests, fracture surfaces were analyzed by SEM, AES, EDS and AFM to make the failure path clear. Results showed that failure path was closely related to the oxidation time and the interfacial fracture toughness.