• Journal of the Korean Wood Science and Technology
• /
• v.29 no.3
• /
• pp.68-72
• /
• 2001

In order to effectively use the waste wood, two types of woodceramics chip tile were made from woodceramics chip, gravel, zeolite and additions. The woodceramics chip was made from branch of apple tree (Malus pumila Mill.) Snow melting property, bending strength and compressive strength of woodceramics chip tile were tested according to the mixing rate of woodceramics chip. Snow melting properties of woodceramics chip tile increased after additions treatment but mechanical properties were reduced significantly after additions treatment. The results indicate that the additions are effective for snow melting property but negative effect on mechanical properties.

• Journal of Korea Foundry Society
• /
• v.13 no.6
• /
• pp.524-531
• /
• 1993

Dispersion behaviors of SiC particles and microstructures in Al-2%Si/SiCp composite prepared by Rheo-compocasting were studied with change of fabrication conditions(slurry temperature, agitation time) and additions of Mg($0{\sim}3wt.%$). Also, the microhardness change of matrix, interface and total in composites were examined with additions of Mg($0{\sim}3wt.%$). The dispersion of particles in the composites became relatively homogeneous with increase of Mg additions, agitation time and decrease of slurry temperature. Rate of occupied area by particle in matrix was increased as increase of Mg additions due to improvement of wettability between SiC particle and matrix. A favorable composites were obtained by melting under Ar atmospheric SiCp injection and bottom pouring system. According to the analysis of X-ray diffraction, $Mg_2Si$, $Al_4C_3$, $SiO_2$ and MgO, etc, intermetallic compounds were formed by chemical interreaction at interface of matrix and particles. The microhardness of interface is higher than that of matrix due to more strengthening of above intermetallic compounds. It was considered that the total hardness of the composites is improved by dispersing of SiCp and addition of Mg.

• Electrical & Electronic Materials
• /
• v.9 no.7
• /
• pp.708-718
• /
• 1996

The microstructure and electrical properties of the nonlinear ZnO varistor with A1$_{2}$ $O_{3}$ additions is investigated. The variation of nonlinear behavior with A1$_{2}$ $O_{3}$ additions is indicated from J-E and C-V measurement to be a result of the change of the interface defects density $N_{t}$ at the grain boundaries and the donor concentration $N_{d}$ in the ZnO grains. The optimum composition which has the nonlinear coefficients of -57 was observed in the sample with 0.005wt% A1$_{2}$ $O_{3}$ additions. The conduction mechanism at the pre-breakdown region is consistent with a Schottky thermal emission process obeying a relation given by $J^{\var}$exp[-(.psi.-.betha. $E^{1}$2/)kT] and the conduction process at the breakdown region follows a Fowler-Nordheim tunneling mechanism of the form $J^{\var}$exp(-.gamma./E).

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2001.02a
• /
• pp.21-24
• /
• 2001

A series of superconducting Hg$Ba_{2}$Cu$O_{4+7}$ materials, containing $Ag_{x}$ additions with molar fraction x = 0, 0.05, 0.1, 0.3, and 0.5, have been studied. This study has showed that Ag additions lead to changes in superconducting properties of Hg-1201 materials. In addition, according to the amount of $Ag_{x}$ additions with molar fraction x up to 0.5, both $T_{c}$ and $J_{c}$ of Hg-1201 materials generally decrease with Ag-content. These and other results are discussed in this paper.

• Journal of the Korean Ceramic Society
• /
• v.19 no.4
• /
• pp.293-299
• /
• 1982

The effects of $MnO_2$ and $Cr_2O_3$ on the Piezoelectrictric properties of Pb(Mg1/2W1/2)0.3 Ti0.4 Zr0.3O3 Ceramics. Electromechanical properties in the system in connection with the sintering temperature and the effects of $MnO_2$ and $Cr_2O_3$ addition. The dielectric constant of the ceramics decreased with the additions of $MnO_2$ while the additions of $Cr_2O_3$ increased the value. The Planar coupling factor (Kp) of the ceramics with 0.2wt% $MnO_2$ and with 0.2wt% $Cr_2O_3$ gave the highest value of 0.52 and 0.513 as sintered at 106$0^{\circ}C$, 108$0^{\circ}C$, respectively. The value of mechanical Q-factor were in parallel with the fired density of the ceramics. The optical micrography of the sintered bodies showed that the additions of $MnO_2$ promoted the grain growth, while the additions of $Cr_2O_3$ retarded the grain growth.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.11a
• /
• pp.311-314
• /
• 1998

The effects of the additions of transition metal oxides on ZrO$_2$ - Y$_2$O$_3$ (Y$_2$O$_3$ - containing tetragonal zirconia polycrystals : Y-TZP) system has been studied by investigating fracture toughness and phase stability of the sintered specimens. In the specimens sintered at 1450$^{\circ}C$ for 2hrs in air the phase transformation from tetragonal to monoclinic was observed. The ratios of monoclinic phase to tetragonal phase were changed with the additions of CoO, Fe$_2$O$_3$ and MnO$_2$, respectively, from 0.00 to 8.00wt%. The fracture toughness was increased with increasing the monoclinic to tetragonal phase ratio and was maximum at the ratio of about 18%. However, the hardness was decreased with increasing the ratio. The additions of CoO, Fe$_2$O$_3$ and MnO$_2$ together into Y-TZP resulted in more complex behaviors of fracture toughness and hardness. The specimen with the additions of 1.5wt% Fe$_2$O$_3$, 3.0wt% Al$_2$O$_3$ and 1.5wt% CoO showed the monoclinic to tetragonal phase ratio of 18% and the highest toughness of 10.8 MPa.m$\^$$\frac{1}{2}$/ and Vickers hardness of 1201kgf/mm$^2$.

• Korean Journal of Materials Research
• /
• v.5 no.2
• /
• pp.157-168
• /
• 1995

The effects of Mo additions on the microstructure and the room temperature deformation behavior of polysynthetically twinned (PST) crystals of TiAl were studied in order to get a basic conception for alloying additions on the two-phase TiAl compounds with the lamellar structure. It was found that the Mo additions in TiAl PST crystals increase both the yield stress and tensile elongation to fracture but the increase in yield stress deppend on the angle $\Phi$at which the lamellar boundaries lie from the loading axis. The large difference in yield stress between specimens deformed parallel($\Phi = 0^\circ$)or perpendicular($\Phi = 90^\circ$) to the loading axis and those deformed in intermediate orientations could be plained by the difference in Mo content between the TiAl and the $$Ti_{3}Al$ phases. It was also found that the Mo-doped specimens with intermediate orientation fail by cracking zigzag across to the lamellar boundaris, which is the same fracture mode as that of binary specimens with intermediate orientations tested in vacuum This suggests that Mo atoms are thought to play a role to reduce the environmental embrittlement of binary PST crystals, resulting in increasing the tensile ductility.

• Journal of Korea Foundry Society
• /
• v.12 no.2
• /
• pp.131-138
• /
• 1992

The effects of B additions, alone or in combination with Si, on the microstructure, $DO_3{\rightleftharpoons}B2$ transition temperature($T_c$) and corrosion behavior of Fe-25at%Al alloys were investigated. The raw materials were arc-melted in vacuum and then subjected to the following heat treatments to maximize the $DO_3$ order : homogenized at $1000^{\circ}C$ for 48hrs, slowly cooled to $500^{\circ}C$, and held at that temperature for 24hours. Results showed that the B addition to Fe-25at%Al alloys does indeed refine the grain and change from intergranular to transgranular fracture mode at room temperature, indicating a strengthening of grain boundaries. The Fe-25at% Al-1at% B-3at% Si alloy showed the highest $T_c$(${\Delta}T_c=150^{\circ}C$) in this work. However, the effectiveness of Si in raising $T_c$ decreased with more than 5at% Si additions combined with B. Since the preferential corrosion occurs at the precipitates, the corrosion resistance decreased due to the increased amount of precipitates with alloying additions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.121-127
• /
• 1998

In this paper, to develop PTCR(Positive Temperature Coefficient of Resistance) thermistor with high withstanding voltage, Ca were added to. the compositions of $(Ba_{0.9165-X}-Sr_{0.08}-Ca_X-Y_{0.0035})TiO_3+MnO_2$ 0.02wt%+$SiO_2$ 0.5wt%. the effects of Ca additions were researched according the increasing of Ca from 0[mol%] to 20[mol%], and the electrical properties were investigated. As increasing Ca additions from 0[mol%] to 20[mol%], the grain size of the specimens was reduced from 11.1[${\mu}m$] to 6.15[${\mu}m$], and also the sintered density was reduced from 5.43[$g/cm^3$] to 5.05[$g/cm^3$] and their the breakdown voltages were increased from 163[V/mm] to 232[V/mm]. It is shown that the breakdown voltage was increased with amount of Ca additions.

• Journal of Korea Foundry Society
• /
• v.3 no.4
• /
• pp.239-247
• /
• 1983

CV graphite cast iron has been studied and generally known to have properties close to the average values of those between flake and spheroidal graphite cast iron. However, the thermal diffusivity of CV graphite cast iron is much larger than that of the average value of those between flake and spheroidal graphite cast iron. In this study, an easy production method of CV graphite cast iron with small additions of a Al-Cu which is known as the element of the graphitization was investigated. The effects of hold time and of Al-Cu additions after the treatments with spheroidizer (Fe-Si-Mg alloy) were also investigated. Increasing the additions of a Al-Cu alloy, the holding time to form a CV graphite cast iron was decreasing. Tensile strength and thermal diffusivity (flash method) were measured in order to find the changes of the mechanical properties and the physical properties. Spheroidal, CV, and flake graphite cast iron have tensile strengths 46.44, 38.29, and $27.29\;kg/mm^2$ and thermal diffusivities $3.95{\times}10^{-6,}$ $8.41{\times}10^{-6}$, $8.81{\times}10^{-6}m^2/sec$, respectively at room temperature.