• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.160-167
• /
• 2010

This paper proposes an adaptive sliding mode observer (SMO), which adds the estimation function of the stator resistance to a new sliding mode observer for the robust sensorless control of permanent magnet synchronous motor (PMSM) with variable parameters. To reduce the chattering problem commonly found in the conventional sliding mode observer where the low-pass filter and additional position compensation of the rotor are used, the sigmoid function is used for the control of a switching function in this research. With the estimation of the stator resistance, the proposed observer can improve the control performance by reducing the estimation error of the motor's speed. Note that the stator resistance is varying with the ambient temperature and becomes an error source for the sensorless control of PMSM. The new sliding mode observer has better efficiency than the conventional adaptive sliding mode observer by reducing the time consuming integral calculations. The stability of the proposed adaptive sliding mode observer is verified by the Lyapunov function in determining the observer gains, and the effectiveness of the observer is demonstrated by simulations and experiments.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.686-686
• /
• 2013

Crystalline silicon solar cell is a semiconductor device that converts light into electrical energy. Screen printing is commonly used to form the front/back electrodes in silicon solar cell. Screen printing method is convenient but usually shows high resistance and low aspect ratio, which cause the efficiency decrease in crystalline silicon solar cell. Recently the plating method is applied in c-Si solar cell to reduce the resistance and improve the aspect ratio. In this paper, we investigated the effect of additional electroless Ag plating into screen-printed c-Si solar cell and compared their electrical properties. All wafers used in this experiment were textured, doped, and anti-reflection coated. The electrode formation was performed with screen-printing, followed by the firing step. Aften then we carried out electroless Ag plating by changing the plating time in the range of 20 sec~5 min and light intensity. The light I-V curve and optical microscope were measured with the completed solar cell. As a result, the conversion efficiency of solar cells was increased mainly due to the decreased series resistance.

• The Korea Journal of Herbology
• /
• v.31 no.1
• /
• pp.1-5
• /
• 2016

Objectives : The purpose of this study was to investigate inhibitory effects of steamed Polygonatum odoratum extract (POE) on insulin resistance in rat skeletal muscle cells, L6 cells.Methods : Polygonatum odoratum (P. odoratum) extract was extracted with ethyl acetate. Activity of α-glucosidase in POE was measured for blood glucose regulation. MTT assay was examined for cell toxicity. Western blot analysis for measurement of adiponectine, peroxisome proliferator-activated receptorγ (PPARγ), insulin receptor substrate (IRS), glucose transporter 4 (Glut-4) and phosphorylation of serine/threonine-specific protein kinase (Akt) expressions were performed. Akt signaling pathway were analyzed with LY294002, which is a specific PI3K/Akt inhibitor.Results : The results revealed that POE inhibited α-glucosidase activity. Treatment of POE in L6 cells inhibited the differentiation of L6 cells compared to those of vehicl control. Additionally, protein expressions of adiponectine, PPARγ, IRS and Glut-4 were significantly regulated compared to those of vehicle control (p < 0.05), respectively. Futhermore, phosphorylation of Akt was increased in L6 cells treated with POE compared to that of vehicle control (p < 0.05). pAkt expression was significantly accentuated with Akt inhibitor (LY294002).Conclusions : These results suggest that POE may have potential as a natural agent for prevention/improvement of diabetes, especially, regulation of blood glucose. Therefore, further additional study should be conducted to elucidate in depth the pharmaceutical efficacy of these.

• Structural Engineering and Mechanics
• /
• v.67 no.1
• /
• pp.1-8
• /
• 2018

Shake table tests performed on five 1:3 reduced scale two story RC moment resisting frames having construction defects, have shown severe joint damageability in deficient RC frames, resulting in joint panels' cover spalling and core concrete crushing. Haunch retrofitting technique was adopted herein to upgrade the seismic resistance of the deficient RC frames. Additional four deficient RC frames were built and retrofitted with steel haunch; both axially stiffer and deformable with energy dissipation, fixed to the beam-column connections to reduce shear demand on joint panels. The as-built and retrofitted frames' seismic response parameters are calculated and compared to evaluate the viability of haunch retrofitting technique. The haunch retrofitting technique increased the lateral stiffness and strength of the structure, resulting in the increase of structure's overstrength. The retrofitting increased response modification factor R by 60% to 100%. Further, the input excitation PGA was correlated with the lateral roof displacement to derive structure response curve that have shown significant resistance of retrofitted models against input excitations. The technique can significantly enhance the seismic performance of deficient RC frames, particularly against the frequent and rare earthquake events, hence, promising for seismic risk mitigation.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.4
• /
• pp.72-83
• /
• 1997

The purpose of present study is to find an appropriate hull shape of a container ship which can operate along the coast and through canals. A 200TEU class container ship is designed with dimensional modifications of an existing 140TEU container ship which is a domestic coastwise vessel. For the fore-body shape including bulbous bow. additional modification is done by changing the sectional area curve and frameline shape using the data of series resistance test. The model tests are performed in the towing tank to measure total resistance sinkage and trim of the model. And a finite-difference method based on MAC method is utilized to analyze the flow field around the ships in deep and restricted water. From the result of model test and numerical analysis, the resistance characteristics of the designed hull form are predicted.

• Steel and Composite Structures
• /
• v.19 no.6
• /
• pp.1381-1402
• /
• 2015

The application of composite steel-concrete slabs with profiled steel sheeting has increased, due to the various advantages in relation to reinforced concrete slabs such as, the reduced thickness, the reduced amount of lost formwork needed, as well as the speed of execution. The loss of longitudinal shear resistance is, generally, the governing design mode for simply supported spans of common lengths. For common distributed loadings, the composite behaviour is influenced by the partial shear connection between the concrete and the steel sheeting. The present research work is intended to contribute to improving the ultimate limit state behaviour of composite slabs using end anchorage. Eurocode 4, Part 1.1 (EN 1994-1-1) provides an analytical methodology for predicting the increase of longitudinal resistance, achieved by using shear studs welded through the steel sheeting as the end anchorage mechanism. The code does not supply an analytical methodology for other kinds of end anchorage so, additional tests or studies are needed to prove the effectiveness of these types of anchorage. The influence of end anchorage mechanisms provided by transverse rebars at the ends of simply supported composite slabs is analysed in this paper. Two experimental programmes were carried out, the first to determine the resistance provided by the new end anchorage mechanism and the second to analyse its influence on the behaviour of simply supported composite slabs.

• Elastomers and Composites
• /
• v.55 no.3
• /
• pp.222-228
• /
• 2020

Rubber materials, used in nuclear power plants, need high heat-oxidation resistance to curing or cracking under a heat aging environment. This is because they are applied to environments with high temperature, high humidity, and radiation exposure. Nuclear radiation causes additional hardening or degradation, therefore, rubber materials need radiation resistance that satisfies the general and any accidental conditions produced in the power plant. Therefore, in this study, we developed a rubber material with excellent heat and radiation resistance for the diaphragm seal of a nuclear steam generator nozzle dam. The rubber material greatly improved the reliability of the steam generator nozzle dam. In addition, 30 inch and 42 inch diaphragm seals were manufactured using the developed rubber material. A nozzle dam was installed in a nuclear power plant and tested under the same conditions as a steam generator to evaluate safety and reliability. In the future, the performance and safety of diaphragm seals developed through field tests of nuclear power plants will be evaluated and applied to currently operating and new nuclear power plants.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.547-550
• /
• 2004

Superconducting fault current limiter(SFCL) is expected to be introduced into electric power system in future as an effective countermeasure for the increase of the short-circuit current due to the growth of the electric power system. SFCL has a merit that the fault current can be limited by the resistance generated when a superconductor transits from a superconducting state to a normal state without additional detecting device. In this paper, we investigated the resistance variance of resistive type SFCL and the fault current limiting characteristics due to the amplitude of source voltage. We could obtain the more effective fault current limiting characteristics of SFCL as the source voltage increased.

• Applied Chemistry for Engineering
• /
• v.31 no.2
• /
• pp.226-229
• /
• 2020

N-phenylmaleimide (PMI), a compound for strengthening the heat resistance of ABS resin, is a yellow crystal. Therefore, copolymers modified with PMI exhibit color, which limits their use. In order to overcome such disadvantage, the demand for N-cyclohexylmaleimide (CHMI), which has similar properties to PMI and also is a white crystal, is increasing. However, CHMI is difficult to industrialize due to the formation of various by-products during synthesis, which requires an additional purification process resulting in a low yield. In this study, composite catalysts were developed to improve these problems and industrially produce CHMI. Finally, CHMI was synthesized with a 85% yield and at least 99.5% purity.

• Structural Engineering and Mechanics
• /
• v.70 no.6
• /
• pp.723-735
• /
• 2019

Track-bridge interaction (TBI) problem often arises from the adoption of modern continuously welded rails. Rail expansion devices (REDs) are generally required to release the intensive interaction between long-span bridges and tracks. In their necessity evaluations, the key techniques are the numerical models and methods for obtaining TBI responses. This paper thus aims to propose a preferable model and the associated procedure for TBI analysis to facilitate the designs of long-span bridges as well as the track structures. A novel friction-spring model was first developed to represent the longitudinal resistance features of fasteners with or without vertical wheel loadings, based on resistance experiments for three types of rail fasteners. This model was then utilized in the loading-history-based TBI analysis for an urban rail transit dwarf tower cable-stayed bridge installed with a RED at the middle. The finite element model of the long-span bridge for TBI analysis was established and updated by the bridge's measured natural frequencies. The additional rail stresses calculated from the TBI model under train loadings were compared with the measured ones. Overall agreements were observed between the measured and the computed results, showing that the proposed TBI model and analysis procedure can be used in further study.