• Proceedings of the Korea Concrete Institute Conference
• /
• 1998.10c
• /
• pp.139-144
• /
• 1998

This study is intended to devolop the self waterproof agents for high performance concrete by analyzing the properties of fresh and hardened mortar with various addition ratios of the inorganic admixture and zinc stearate. As the results of the test, the flow and air content increase with the addition of expansive additives. When the replacement rate of silica fume increases, the flow decreases for the increased viscidity. And the flow and sir content decrease with the addition of zinc stearate. At hardened state, the compressive strength, tensile strength and flexual strength decrease with the addition of expansive additives and zinc stearate. With the increase of silica fume's replacement, they show a little decrease at early age and then increase gradually. Also, absorption and permeability show a steep decrease when zinc stearate is added, and a slack decrease with the replacement of silica fume.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.7
• /
• pp.60-74
• /
• 1993

Experiments of RIE of tungsten films using SF$_{6}$ plasma were conducted to investigate the effect of process parameters on etch rate, uniformity, anisotropy, and selectivity. As power increased, the etch rate increased. Maximum etch rate was obtained at 200mtorr As interelectrode spacing increased the etch rate increased for P < 200mtorr while it decreased for P> 200mtorr. Etch rate was maximum at 20 sccm gas flow rate. As substrate temperature increased, the etch rate increased and activation energy was 0.046 eV. In addition, maximum etch rate was acquired at 20% $O_{2}$ addition. The etch rate slightly increased when Ar was added up to 20% while it continuously decreased when N$_{2}$ was added. Uniformity got improved as pressure decreased and was less than 4% for P <100mtorr. Mass spectrometer was utilized to analyze gas composition and S and F peaks were observed from XPS analysis with increasing power. The anisotropy was better for smaller power and spacing, and lower pressure and temperature. It improved when CH$_{4}$ was added and anisotropic etch profile was obtained when about 10% $O_{2}$ was added. The selectjvity was better for smaller power larger pressure and spacing, and lower temperature. Especially. low temperature processing was proposed as a novel method to improve the anisotropy and selectivity.

• Corrosion Science and Technology
• /
• v.4 no.2
• /
• pp.39-44
• /
• 2005

The purpose of this work is to understand the effect of Mo addition on SSC susceptibility of high strength low alloy steels in terms of microstructure and corrosion property. Materials used in this study are high strength low alloy (HSLA) steels with carbon content of 0.04wt% and Mo content varying from 0.1 to 0.3wt%. The corrosion property of steels was evaluated by immersion test in NACE-TM01-77 solution A and by analyzing the growth behavior of surface corrosion products. SSC resistance of steels was evaluated using constant load test. Electrochemical test was performed to investigate initial corrosion rate. Addition of Mo increased corrosion rate of steels by enhancing the porosity of surface corrosion products. However, corrosion rate was not directly related to SSC susceptibility of steels.

• Journal of Microbiology and Biotechnology
• /
• v.1 no.3
• /
• pp.197-201
• /
• 1991

Glycerolysis of triolein by lipase from Chromobacterium viscosum lipase was studied batchwise in AOT-isooctane reversed micelles. The reaction mixture was extracted with chloroform and the content of triolein, 1, 2-diolein, 1, 3-diolein, 1-monoolein, and free fatty acid in the condensed chloroform solution was determined using high performance liquid chromatography (HPLC). The effect of agitation speed on the initial rate of conversion was examined. As the speed of agitation increased up to 700 rpm, the reaction rate increased. However, above 700 rpm, the rate approached maximum and did not increase that much. The glycerolysis activity and the stability of the enzyme were affected by stirring and addition of histidine or copper. Addition of histidine and copper increased the rates of glycerolysis but they are detrimental to the operational stability in reversed micelles.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.04a
• /
• pp.23-26
• /
• 1997

This work presents the TMAH/IPA anisotropic etching characteristics with addition of Pyrazine. (100) Si etching rate of 0.747 ${\mu}{\textrm}{m}$/min at 8$0^{\circ}C$ was obtained using TMAH 25 wt.% / IPA 17 vol.% / pyrazine 0.1 g. The etching rate of (100) Si is increased about 52% compare to pure TMAH 25 wt.%. But etching rate of (100) Si is decreased with increasing Pyrazine additive. Activation energy of TMAH/IPA/pyrazine is much lower than TMAH and TMAH/IPA solutions. Addition of Pyrazine does not effect on surface flatness and decreases undercutting ratio about 20 %. Therefore, TMAH/IPA/pyrazine is an attractive anisotropic etchant because of alkaline-ion free.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.35-36
• /
• 2022

In order to supplement the flame-retardant performance of oil stain, which can prevent wooden buildings from contamination, (NH4)2HPO4, a phosphorus flame-retardant, was added to oil stain and applied for each type of plywood, and an experiment was conducted. The addition rate was set to 0-60%, but white powder appeared on the surface of plywood from 40% and thus it was impossible to experiment, so the maximum addition rate was selected as 30%. As a result of the experiment, acacia plywood had the best performance. As the rate of addition of the flame retardant increased, the remaining time and carbonization length of all plywood decreased, but the carbonization length of the MDF plywood was not met with the standards.

• Clinical and Experimental Pediatrics
• /
• v.54 no.11
• /
• pp.429-435
• /
• 2011

Although Korean population has been growing steadily during the past four decades, the nation is rapidly becoming an aging society because of its declining birth rate combined with an increasing life expectancy. In addition, Korea has one of the lowest fertility rates in the world due to fewer married couples, advanced maternal age, and falling birth rate. The prevalence of low birth weight infants and multiple births has been increased compared with the decrease in the birth rate. Moreover, the number of congenital anomalies is expected to increase due to the advanced maternal age. In addition, the number of interracial children is expected to increase due to the rise in the number of international marriages. However, the maternal education level is high, single-mother birth rate is low, and the gender imbalance has lessened. The number of overweight babies has been decreased, as more pregnant women are receiving adequate prenatal care. Compared to the Asian average birth weight, the average birth weight is the highest in Asia. Moreover, the rate of low birth weight infants is low, and infant mortality is similarly low across Asia. Using birth data from Statistics Korea and studies of birth outcomes in Korea and abroad, this study aimed to assess the changes in maternal and infant characteristics associated with birth outcomes during the past four decades and identify necessary information infrastructures to study countermeasures the decrease in birth rate and increase in low birth weight infants in Korea.

• The Journal of Asian Finance, Economics and Business
• /
• v.8 no.3
• /
• pp.731-740
• /
• 2021

This research aims to investigate the determinants of real effective exchange rate in emerging ASEAN countries, including Indonesia, Malaysia, Philippines, Thailand, and Vietnam. The research was conducted by using quarterly time series data set from 1980Q1 to 2020Q3. Cointegration and the error correction model (ECM) methods were applied to test the long run and short run relationship of the real effective exchange rate and its determinants. The results indicate that the ratio of foreign direct investment to GDP and the government spending have significantly positive impact on real effective exchange rate in the Emerging ASEAN countries. The trade opening had influencing real effective exchange rate in most the Emerging ASEAN countries, except Vietnam. In addition, the international reserve (INR) had significant long-run impacts variables on real effective exchange rate in Malaysia, Thailand and Vietnam. In the short run equilibrium, the error collection term suggest that Indonesia and Malaysia are the fastest speed adjustment to equilibrium. In addition, the term of trade influence the real effective exchange rate in Indonesia, Malaysia, and the Philippines but it is not in Thailand and Vietnam. However, FDI is a major factor of the real effective exchange rate in Vietnam, but not for other countries.

• Journal of Korea Foundry Society
• /
• v.27 no.6
• /
• pp.243-249
• /
• 2007

The effect of Re addition and solidification rate on the directional solidification behavior of Ni-Al model alloy has been investigated. Directional solidification (DS) were carried out using the modified Bridgman furnace with various solidification rates. The solid/liquid interface during directional solidification was preserved by quenching the specimen after the desired volume fraction of original liquid was solidified. The equilibrium partition coefficients of Al and Re Were estimated by measuring the compositions at the quenched solid/liquid interface. Then, the effect of Re addition on the elemental segregation behavior was carefully analyzed. The differential scanning calorimetry results showed that the Re addition results in increased ${\gamma}'$ solvus and freezing range of the alloy. It was also shown that the primary dendrite arm spacing gradually decreases with increasing the Re content, while the secondary dendrite arm spacing appears to be independent on the Re content. The compositional analyses clearly revealed that the segregation of Al increased with increasing the Re content and solidification rate, while that of Re was found to be independent on the solidification rate in the range of $10{\sim}100{\mu}m/s$ due to its sluggish diffusion rate in the Ni solid solution.

• Korean Journal of Materials Research
• /
• v.18 no.2
• /
• pp.73-76
• /
• 2008

[ $SF_6$ ] gas has been widely used as an insulating, cleaning and covering gas due to its outstanding insulating feature and because of its inert properties. However, the global warming potential of $SF_6$ gas is extremely high relative to typical global warming gases such as $CO_2$, CFCs, and $CH_4$. For these reasons, it is necessary to separate and collect waste $SF_6$ gas. In this study, the effects of a surfactant (Tween) on the formation rate of $SF_6$ gas hydrates were investigated. The $SF_6$ gas hydrate formation rate increased with the addition of Tween and showed a nearly 6.5 times faster hydrate formation rate with an addition of 0.2 wt.% Tween compared to an addition of pure water. This is believed to be due to the increased solubility of $SF_6$ gas with the addition of the surfactant. It was also found that $SF_6$ gas hydrate in the surfactant solution showed two-stage hydrate formation rates with a formation rate that increased rapidly in the 2nd stage.