• 한국군사과학기술학회지
• /
• 제8권2호
• /
• pp.77-87
• /
• 2005

The thermomechanical characteristics were evaluated for 17-4PH stainless steel widely used in supersonic airframe subjected to both aerodynamic loading and heating. The thermomechanical tests were conducted under both elevated temperature and rapid heating condition from $1^{\circ}C/sec\;to\;28^{\circ}C/sec$. The thermomechanical behaviors under rapid heating were compared with those of elevated temperature after 1/2 hour exposure in terms of yield stress to investigate the influence of heating rates. A heating rate-yield temperature parameter was suggested for rapid heating based on time-temperature parameters, and master yield stress curve was obtained by using these parameters. The experimental results and methodology from this study can be used as basic engineering data when designing supersonic vehicle structures subjected to aerodynamic loading and severe heating environment.

• 한국의류학회지
• /
• 제28권7호
• /
• pp.1029-1036
• /
• 2004

The fragrant fabrics were prepared by treatment with eucalyptus microcapsules. 100% cotton fabric, 100% polyester fabric and 100% wool fabric were used as test specimens. Using pad-dry-cure method, microcapsules were attached on each specimen by acrylic binder under conditions of varying concentration. Surface property, stiffness, and air permeability of fragrant fabrics were evaluated. As increasing concentration of binder, add-on yield was increased. Add-on yield was decreased with increasing laundering cycle, especially in polyester fabric. As the concentration of binder was increased, the properties of stiffness and air permeability were decreased. Also it fumed out that pad-dry-cure method was not suitable to polyester fabric.

• 약학회지
• /
• 제33권6호
• /
• pp.365-371
• /
• 1989

Microbiological conversion of sterols to 17-ketosteroids has been recognized as a source for commercial preparation of steroidal drugs. In order to develop bacterial strains and process with Brevibacterium lipolyticum IAM 1398 capable of converting cholesterol to 1,4-Androstadiene-3,17-dione (ADD) at about 27% yield, we studied on strain improvement, fermentation condition and whole cell immobilization. By using UV and/or NTG as mutagens, a mutant to convert cholesterol to ADD with higher yield than 60% was selected. Better production of ADD was manifested in the case of maltose used as a supplemental carbon source, and yeast extract or soytone as a nitrogen source. Addition of tween 80 (0.05%) as a surfactant beneficial for increasing the productivity. The optimal initial pH of the medium was 6.5 and optimal culture temperature was $30^{\circ}C$. Whole cell immobilization by using carrageenan, agar, alginate and acrylamide was carried out and the activity of conversion was tested. In the case of carrageenan and agar, immobilized cells were active for at least two cycles of fermentation.

• 한국염색가공학회지
• /
• 제14권6호
• /
• pp.313-318
• /
• 2002

Chitosan is known to be an excellent biocompatible natural polymer. Recently, with a growing interest of health and environment, chitosan which is good in no harmful effect on human body and environment, has been watched as the finish treatment of hygiene and pleasantness. The purpose of this study is to develop multi functional fabrics by chitosan added on acrylic acid grafted cotton fabrics. Therefore physical properties such as moisture regain, air permeability, whiteness, static voltage and tensile strength of chitosan added on acrylic acid grafted cotton fabrics were investigated. The results are as follows ; According to increased chitosan's concentration, grafting yield was decreased. Therefore thickness of film by treated chitosan added on acrylic acid grafted cotton fabric became thin. FT R spectra of chitosan add on acrylic acid grafted cotton fabric clearly showed peaks of COOH and $NH_2$, Moisture regain, static voltage of chitosan add on acrylic acid grafted cotton fabrics were increased than control. Air permeability, whiteness and tensile strength were decreased than control.

• 한국의류학회지
• /
• 제27권11호
• /
• pp.1252-1259
• /
• 2003

The purpose of this study is to develop multi-functional fabrics by chitosan added on acrylic acid grafted cotton kintted fabrics. Therefore physical properties such as antimicrobial activity, deodorization rate, moisture regain, whiteness, and tensile strength of chitosan added on acrylic acid grafted cotton kintted fabrics were investigated. The results are as follows; According to increased chitosan's concentration, grafting yield was decreased. Therefore thickness of film by treated chitosan added on acrylic acid grafted cotton kintted fabric became thin. FT-IR spectra of chitosan add on acrylic acid grafted cotton kintted fabric clearly showed peaks of COOH and NH$_2$. Antimicrobial activity and deodorization rate of chitosan add on acrylic acid grafted cotton kintted fabrics were increased greatly than untreated. And their durability of laundry were good, Moisture regain of treated fabrics was higher than untreated. Whiteness and tensile strength of treated fabrics were lower than untreated.

• 한국유기농업학회지
• /
• 제8권1호
• /
• pp.89-99
• /
• 1999

To do mass multiplication of plug seedlings in potatoes, apical stem cuttings originated from virus-free microtubers were cut to one-two internodes and transplanted into the plug-tray. After 10days, we applied Chitosan and Wood Extraction on rooting and tuber formation of plug seedlings. To improve field adaptability of plug seedlings, rooted cuttings with a height of 20cm after 20days of cutting were transplanted ito the fields, We applied 500~2000ppm Chitosan on growth characteristics and tuber formation of that. The above and underground growths, such as plant height and number of leaves were significantly more vigorous after treatment with 500~1,000ppm Chitosan and 2,000ppm Wood Extraction, the spray treatment was carried out five times at intervals of four days after ten days of transplanting. T-N, K, P, Mg and Na, were higher as the concentrations of chitosan and Wood Extraction were higher. The growth and tuber yield in plug seedlings planting plot and seed potatoes planting plot were effectively highter as foliar application of Chitosan(500~2,000ppm) was done after planting the plot. T-N content in leaves and tuber was higher as the concentration of Chitosan was high. A similar tendency was shown in K, P and Mg. In the small tuber(under 30g), the number of tubers and tuber yield were relatively increased in the seed potatoes planting plot, but the large tubers(over 80g) yield was higher in the plug seedlings planting plot, and in order to increase tuber yield in plug seedlings it was necessary to add plant density to the field.

• Asian-Australasian Journal of Animal Sciences
• /
• 제19권3호
• /
• pp.309-314
• /
• 2006

The present investigation was undertaken to study the milkability characteristics of Holstein cows. Out of 6,660 initial records 4,607 records were finally included in the analysis after deleting some records with an abnormal range of values for the traits considered. These 4,607 Holstein cows belonged to a total of 122 herds located in a province in Korea. The 'LactoCorder' instrument was used to electronically record the milkability traits at the milking parlor. A total of 19 traits were studied which were broadly classified into milk yield, milking speed, milking time and the electrical conductivity related traits. The SAS 9.1 statistical software was used to carry out analyses. The average maximum milk flow per minute was 3.21 kg/min, while the average milking speed during the main milking process (DMHG) had a mean value of 2.30 kg/min. The total milk yield was 14.14 kg, 62% of which was milked during the first three minutes of the milking. The average total milking time was 8.23 min. Among the three phases of the main milking process, the time of stable milk flow had the longest time (2.97 min) followed by the time at the decline phase (2.62 min). The average time taken to reach the plateau phase was 1.08 min, which can still be reduced further through improved managemental practices. Among milk yield traits, milk yield during the first two (MG2) and three (MG3) minutes of milking had high positive correlation with milking speed traits and negative correlations with almost all the milking time traits except time of incline in milk flow from 0.5 kg/min till the attainment of the plateau phase (tAN). Milking speed traits had negative correlations with total milking time, time at main milking process, time at plateau and with the time at decline. Since there was medium to high negative correlation between the milking speed and the time at plateau, there is a need for selection of cows which have intermediate milking speed so that it could require less milking time and also the optimum (higher and longer) plateau time. Proper pre-stimulation and avoiding over milking will help in further reducing the milking time and thus will add to the net profit of the farmer.

• 산업경영시스템학회지
• /
• 제36권1호
• /
• pp.24-35
• /
• 2013

A cell formation approach based on cluster analysis is developed for the configuration of manufacturing cells. Cell formation, which is to group machines and parts into machine cells and the associated part families, is implemented to add the flexibility and efficiency to manufacturing systems. In order to develop an efficient clustering procedure, this paper proposes a cluster analysis-based approach developed by incorporating and modifying two cluster analysis methods, a hierarchical clustering and a non-hierarchical clustering method. The objective of the proposed approach is to minimize intercellular movements and maximize the machine utilization within clusters. The proposed approach is tested on the cell formation problems and is compared with other well-known methodologies available in the literature. The result shows that the proposed approach is efficient enough to yield a good quality solution no matter what the difficulty of data sets is, ill or well-structured.

• 한국염색가공학회지
• /
• 제16권3호
• /
• pp.22-30
• /
• 2004

The polyester fabrics were treated with the chitosan with various solubility in optimized treatment condition. The treatment method was discussed to be a high functional finishing for the polyester fabric to obtain the high moisture absorption and anti-microorganism property by evaluating the effect of the chitosan purification method on the yield and anti-microorganism property of the chitosan. On the other hand, soluble polyurethane was added to the chitosan treatment solution and/or plasma pretreatment was done. The addition of soluble polyurethane give a high add-on ratio as well as a linen like effect of treated polyester fabric. The results were as follows: 1. In the treatment of polyester fabric by the chitosan solution, a soluble PU resin and low temperature plasma treatment were done to obtain high binding force between the fabrics and the chitosan. The add-on rate and the moisture absorption ratio of the fabrics treated with the chitosan-PU after treated with the plasma slightly increased more than those of the fabrics treated with the chitosan only. 2. Anti-static property of the fabrics treated with the chitosan decreased rapidly with increasing of the chitosan concentration. The washing fastness of the fabrics treated with the chitosan-PU after treated with the plasma was better than those of the fabrics treated with chitosan only. The wrinkle resistance of the treated fabrics decreased constantly with the concentration of the chitosan. The bending rigidity of the treated fabrics increased greatly. On the treatment of polyester fabric under optimum condition, the microorganism reduction rate kept above 90％ after 10times launderings. 3. As the polyester fabrics which has flat yam was used as a weft yams were treated with the chitosan-PU as give a functional finishing effects such as durability, moisture absorption, anti-static and anti- microorganism property. Treated polyester fabric showed a good functional finishing effect and a linen like property.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.410-415
• /
• 2010

제트연료변경에 따른 엔진 운용 특성 변화를 살펴보기 위해 JP-8 연료와 JP-S 연료를 사용하여 소형터보제트엔진의 지상시험 및 고도시험을 수행하였다. 비중이 18% 높은 JP-S 연료에 대한 연료조절 시스템 특성은 동일 연료공급명령에 대한 실 연료공급량이 JP-8 연료보다 8% 많이 공급되었다. 시동 특성은 연료조절시스템의 명령 대비 공급량의 차이로 인한 점화시점 및 엔진 회전수 가속율 등의 변화를 제외하고는 유사한 특성을 보였다. 정상상태 성능 특성은 순 추력의 일부 구간을 제외하고는 순추력과 공기유량, 배기가스온도 등 대부분의 엔진 성능 변수가 1% 이내로 유사하였으나 연료소모량만은 연료의 발열량 차이로 인해 최대 5 %이상 차이가 발생하였다. 이를 동일 추력 대비 비 연료소모율로 비교할 때 지상시험에서는 약 1.1~2.6 %, 고공환경시험에서는 5 % 이상 차이가 발생하였다.