• 한국정밀공학회지
• /
• 제19권3호
• /
• pp.137-143
• /
• 2002

This paper presents the In-process compensation to control cutter runout and improve the machined surface quality. Cutter runout compensation system consists of the micro-positioning servo system with piezoelectric actuator which is embeded in the sliding table to manipulate radial depth of cut in real-time. Cutting force feedback control was proposed in the angle domain based upon repetitive learning control strategy to eliminate chip load variation in end milling process. Micro-positioning control due to adaptive actuation force response improves the machined surface quality by compensation runout effect induced cutting force variation. This result will provide lots of information to build-up the preciswion machining technology.

• 제어로봇시스템학회논문지
• /
• 제14권12호
• /
• pp.1218-1225
• /
• 2008

This paper presents the design of a neural network based adaptive control for missile is presented. The application model is Exocet MM40, which is derived from missile DATCOM database. Acceleration of missile by tail Fin control cannot be controllable by DMI (Dynamic Model Inversion) directly because it is non-minimum phase system. So, the inner loop consists of DMI and NN (Neural Network) and the outer loop consists of PI controller. In order to satisfy the performances only with PI controller, it is necessary to do some additional process such as gain tuning and scheduling. In this paper, all flight area would be covered by just one PI gains without tuning and scheduling by applying mixture control technique of conventional controller and NN to the outer loop. Also, the simulation model is designed by considering non-minimum phase system and compared the performances to distinguish the validity of control law with conventional PI controller.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.77-79
• /
• 2006

While RSW(Resistance Spot Welding) have been the most successful sheet metal joining process in automotive industry, there are certain qualify issues due to the control system and its application process. Recent materials and coatings make the process more complicated resulting in new challenges for quality welds. In this research, an intelligent RSW system with adaptive control algorithm is introduced to overcome typical RSW issues and its applications to automotive body assembly are presented.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.240-245
• /
• 1990

A on-line optimization scheme based on model in a binary distillation process is proposed. A reduced-order model utilized the concept of collocation is used as a process model and the recursive prediction error method is employed to identify the reduced-order model. The concentrations of end products are controlled by nonlinear adaptive predictive control algorithm. The objective function is constructed to find optimum operate condition for saving utility cost. The proposed optimization is scheme is tested through simulation studies in 13-staged water-methanol distillation column.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.344-349
• /
• 1990

Under the assumption that process input/output data are sufficiently rich to allow reasonable plant identification, a long-range predictive control method for SISO bilinear plant is derived. In order to ensure offset-free behaviour of the control method, a new bilinear CARIMA model with variable dead-time is introduced. Furthermore, to extend the maximum output prediction horizon, the future predicted outputs in the bilinear term are assumed to be equal to the known future set-points. With a classical recursive adaptation algorithm, the proposed control scheme is capable of stable control of bilinear plants with variable parameters, with variable dead-time, and with a model order which changes instantaneously. Several simulation results demonstrate the characteristics of the proposed bilinear model predictive control method.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권4호
• /
• pp.13-18
• /
• 2003

This paper presents the in-process compensation to control cutter ronout and to improve the machined surface quality. Cutter ronout compensation system consists of the micro-positioning servo system with piezoelectric actuator which is embeded in the sliding table to manipulate radial depth of cut in real-time. Cutting force feedback control was proposed in the angle domain based upon repetitive learning control strategy to eliminate chip load variation in end milling process. Micro-positioning control due to adaptive actuation force response improves the machined surface quality by cutter ronout compensation.

• 한국정밀공학회지
• /
• 제22권12호
• /
• pp.51-60
• /
• 2005

This paper describes a robust control scheme for high-speed and long stroke scanning motion of high precision linear motor system consisting of linear motor, air bearing guide and position measurement system using heterodyne interferometer. Nowadays, semiconductor process and inspection of wafer or LCD need high speed and long travel length for their high throughput and extremely small velocity fluctuations or tracking errors. In order to satisfy these conditions, linear motor system are widely used because they have large thrust force and do not need motion conversion mechanisms such as ball screw, rack & pinion or capstan with which the system are burdened. However linear motors have a problem called force ripple. Force ripple deteriorates the tracking performances and makes periodic position errors. So, force ripple must be compensated. To maximize the tracking performance of linear motor system, we propose the control scheme which is composed of a robust control method, Time Delay Controller (TDC) and a feedforward control method, Zero Phase Error Tracking Control (ZPETC) for accurate tracking a given trajectory and an adaptive force ripple compensation (AFC) algorithm fur estimating and compensating force ripple. The adaptive ripple compensation is continuously refined on the basis of tracking error. Computer simulation results based on modeled parameters verify the effectiveness of the proposed control scheme for high-speed, long stroke and high precision scanning motion and show that the proposed control scheme can achieve a sup error tracking performance in comparison to conventional TDC control.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1989년도 한국자동제어학술회의논문집; Seoul, Korea; 27-28 Oct. 1989
• /
• pp.160-165
• /
• 1989

This paper deals with the robust controller design of robotic manipulator to track a desired trajectory in spite of the presence of unmodelled dynamics in cause of nonlinearity and parameter uncertainty. The approach followed in this paper is based on model reference adaptive control technique and convergence on hyperstability theory but it does away with assumption that process is characterized by a linear model remaining time invariant during adaptation process. A computer simulation has been performed to demonstrate the performance of the designed control system in task coordinates for stanford manipulator with payload and disturbances.

• 한국시뮬레이션학회논문지
• /
• 제19권3호
• /
• pp.45-54
• /
• 2010

반도체 제조공정에 내재된 복잡성은 작업일정(job scheduling) 문제를 해석적 방법으로는 풀기 어렵기 때문에 보통 시스템 파라미터의 변화에 대한 효과를 이산사건 모델링 시뮬레이션에 의존하여 왔다. 한편 장비 고장 등 예측 불가능한 사건들은 고정된 작업일정 기법을 사용할 경우 전체 공정의 효율을 악화시킨다. 따라서 이러한 불확실성에 대해 최적의 성능을 내기 위해서는 작업일정을 실시간으로 대처 변경하는 것이 필요하다. 본 논문은 반도체 제조 공정에 대해 시스템 제어관점의 접근방법을 적용하여 이 문제에 적응형 실시간 작업제어 틀을 제안하고, DEVS 모델링 시뮬레이션 환경을 기반으로 제안된 틀을 설계 구현하였다. 제안된 방법은 기존의 임기응변적인 소프트웨어적인 방법에 비추어볼 때 전체 시스템을 이해하기 쉬우면서도 또한 추가되는 작업제어 규칙도 쉽게 추가 적용할 수 있는 유연성을 장점으로 가지고 있다. 여러 가지 실험결과 제안된 적응형 실시간 작업제어 프레임워크는 고정 작업규칙 방법에 비해 훨씬 나은 결과를 보여주어 그 효용성을 입증하였다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1986년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 17-18 Oct. 1986
• /
• pp.352-355
• /
• 1986

In this paper, some candidates suggested for the improvement of the robustness in adaptive control systems are shortly surveyed. Using dead zone concept of error in adaptation process, gain retardation methods such as .sigma.-modification and parameter restriction method are those considered. Feedforward compensation and normalized adaptation technique are also considered. New modeling technique suggested by Donati et al is used for the indirect control of plants containing unmodeled dynamics. The frequency band of input signal, which is used as a test signal and control signal simultaneously, is directly related to the control of plants containing high frequency parastics. Computer simulation results of the some selected algorithms are shown.