• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.450-453
• /
• 1995

The beam rotating actuator, which can be utilized to improve the data transfer rate for the optical disk systems, has been developed. It can employ a newly developed laser beam rotating actuator for putting multi-beam spots on more than one track on the optical disk simultaneously. Therefore, It has to maintain up to .+-.0.01 .deg. resolution and high bandwidth performance. In this these, the Dove prism is used for the beam rotating actuator based on bimorph piezo material. The performance of the beam rotating actuator is verified since the dynamics ferquency performance is measured using the dynamic analyzer and the attached stain gage sensor. the beam rotating angle performance is also examined since the long range beam reflection character is utilized.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.782-787
• /
• 2002

In optical disk drives (ODD), the demands of high data density and high speed have been increasing rapidly to achieve high data capacity and data transfer rate. The short wavelength laser, High NA objective lens, and high track following performance are needed to raise data density and data rate. For high-performance actuator, the improvement of linearity and acceleration become more important. Also, 3-axis actuator for active tilt compensation is introduced to overcome the decrease in disk tilt tolerance which is induced by short wavelength laser. In this paper, a hybrid type 3-axis actuator is presented and a new yoke structure, which can reduce the interaction between yoke and moving magnet, is designed to keep the efficiency of magnetic circuit. Experimental results show the validity of the yoke in the hybrid type actuator.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.346-350
• /
• 1996

In optical disk drives, one of commonly used pickup actuator is a Sliding and rotary type of pickup actuator which is cheaper than other pickup actuators and has simple assembly. However, it reported that non-linearity due to friction between a shaft and a sleeve had to be considerably analyzed in design and servo system in employing this type of pickup actuator. In this paper, this friction is modeled as a Coulomb's friction and the effect of friction is examined in the simulation. A digital servo system is applied to pickup actuator with friction in order to have good focusing servo. To enhance focusing servo performance using digital servo merit, frist PD-controller is applied to have fast response performance, second lead-lag compensator is applied to have stable focusing performance.

• 한국항공우주학회지
• /
• 제41권6호
• /
• pp.429-439
• /
• 2013

본 연구에서는 로터 성능 해석을 위한 로터 성능 해석자를 개발하고 이를 사용하여 방풍 구조물 내부의 로터 성능 해석을 수행하였다. 로터 성능 해석자는 깃요소 이론 기반의 actuator disk model을 사용한 해석자를 사용하였다. 또한, 주변의 구조물로 인한 로터 하중의 비대칭성을 고려하기 위해 깃요소 이론에서 블레이드의 flapping 운동에 대한 해석을 수행하여 유효받음각 계산에 적용하였다. 개발된 해석자를 사용하여 바닥면과 벽면에 의한 로터 성능 변화에 관한 연구와 비교 검증을 수행하였다. 방풍 구조물 형상에 따른 로터 성능 해석을 통해 방풍 구조물에 의한 로터 성능 감소 현상을 확인하였다. 이를 통해 방풍 구조물이 없는 경우 대비 95% 이상의 로터 성능 비를 가지는 방풍 구조물의 유출입덕트 면적을 제안하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.474-478
• /
• 2006

It is becoming more significant to develop a rotary voice coil motor(VCM) type's actuator for small form factor (SFF) optical disk drive(ODD), as portables are getting more and more popularized nowadays. The actuator which is applicable to small-sized ODD with a compact flash(CF) II card size was developed and fabricated. The experimental results showed that the finite element(FE) model is different from the fabricated model. And so flexible mode frequencies did not satisfy specifications of small-sized ODD, and tuning. Tuning procedures were required to improve dynamic characteristics of the fabricated actuator through finite difference method(FDM). At first, design variables were extracted through parameter study and the tuned FE model was improved by design of experiment(DOE). Consequently, It was confirmed that the improved model was applicable to SFF ODD.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.479-483
• /
• 2006

As high-definition television(HDTV) broadcasting were generalized, there have been many researches and developments about large storage capacity and fast data transfer rate in optical disk drives(ODD). Pickup actuators must have high flexible mode frequencies and gain margins. Flexible modes are caused by the flexibility of moving parts in the actuator and a servo bandwidth is limited by them. As a result, the system becomes unstable for high-speed operations in high density reading and recording. In this paper, we suggest improved modeling method that considers the bonding layer. And, flexible mode frequency of actuator is improved by Design of Experiment of lens holder. Magnet circuit is designed considering the relation with moving part. Through improving yoke design, the magnetic flux is changed and DC tilt is reduced. Consequently, we designed actuator which has high flexible mode frequency and gain margins.

• 정보저장시스템학회논문집
• /
• 제2권4호
• /
• pp.240-244
• /
• 2006

As high-definition television(HDTV) broadcasting becoming more generalized, there have been many researches and developments about a large storage capacity and a fast data transfer rate in optical disk drives (ODD). Pickup actuators must have high flexible mode frequencies and large gain margins. Flexible modes are caused by the flexibility of moving parts in the actuator and a servo bandwidth is limited by them. As a result, the system becomes unstable for high-speed operations in high density reading and recording. In this paper, we suggest improved modeling method in considering of the bonding layer. And, the flexible mode frequency of actuator is improved by Design of Experiments of lens holder. The Magnet circuit is designed considering the relation with the moving part. Through improving the yoke design, the magnetic flux is changed and the DC tilt is reduced. Consequently, we designed an actuator which has a high flexible mode frequency and a large gain margins.

• Transactions on Control, Automation and Systems Engineering
• /
• 제3권3호
• /
• pp.146-151
• /
• 2001

Optical disk drive has excellent advantage of random accessibility of which performance is measured by access time. However, due to the increased rotational velocity of the disk and constraints of mechanical structure, two-stage seek algorithm which executes coarse and fine seeks sequentially has been adopted in most commercial optical disk drives. Although the laser spot is moved to a target track by a single seek operation, the limited operation range of the fine actuator restricts the application of the fine seek algorithm below a few hundreds of tracks. Especially, excessive movement of the objective lens causes a failure in generation of track-cross pulse and results in an unstable seek operation. In this paper, a new control algorithm for extending the fine seek range is proposed with an appropriate control structure. The coarse actuator is utilized to reduce the misalignment between the objective lens and the laser beam axis, and the fine actuator is controlled to follow the reference velocity trajectory. The proposed algorithm is applied to a CD-ROM drive to show its feasibility and some experimental results are presented.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.485-491
• /
• 2000

We obtain the mathematical model of the hard disk drive actuator system from the system response data of the finite element analysis or experimental results. System response data including the dynamics of the considered system are expressed as the mathematical model. It allows the dynamic analysis of the actuator system without resort to the repetitive finite element modeling work. Even though the dynamic characteristics of the system are affected somewhat by the structural modification and the change of the dynamic properties, we can use the modified size and material properties of the actuator system in the mathematical model to some extent. In this study, we express the mathematical model of the simplified rectangular plate first and then proceed to the actual hard disk drive actuator system.