• 한국정밀공학회지
• /
• 제29권3호
• /
• pp.302-306
• /
• 2012

Bacterial cellulose based actuator with large displacement was developed for biomimetic robots. Bacterial cellulose has 3D nanostructure with high porosity which was composed of the nanofibers. Freeze dried bacterial cellulose was dipped into ionic liquid solution such as 1-butyl-3-methylimidazolium(BMIMCl) to enhance the actuation performance due to increase the ionexchange capacity and ionic conductivity. And Poly(3,4-ethylenedioxythiophene)-poly (styrnenesulfonate)(PEDOT:PSS) was used for the electrodes of both side of bacterial cellulose actuator by dipping and drying method. The FT-IR and XRD were conducted to examine the electrochemical changes of developed bacterial cellulose actuator. The biomimetic caudal fin was designed using bacterial cellulose actuator and PDMS to verify the possibility for biomimetic robot. The step and harmonic response were conducted to evaluate the performance of developed biomimetic actuator.

• 제어로봇시스템학회논문지
• /
• 제18권10호
• /
• pp.921-927
• /
• 2012

In this paper we deal with a hydraulic tilting actuator to make a diagnosis of load characteristic acting on the tilting actuator of the tilting train. Tilting actuator in the tilting train plays a role of making tilt of the train when the train runs a curve section to make the train run without deceleration. However in the process of tilt the tilting actuator is affected by the load acting on the actuator, which has a possibility to make bogie vibration. In order to figure out the effect of the load on the tilting actuator a hydraulic tilting devices that are capable of tilting the train is proposed. The proposed devices are installed in the front bogie and in the rear bogie to make tilting of the train. The devices are consist of sensors that measure the load capacity of the actuator and displacement of the hydraulic cylinder stroke, control blocks to make synchronization of the two actuators, user interface block to monitor the status of the actuators. The effectiveness of the proposed hydraulic tilting actuators is presented by the experimental evaluation using actual tilting train.

• 한국소음진동공학회논문집
• /
• 제17권11호
• /
• pp.1043-1049
• /
• 2007

데이터 전송률과 저장용량은 광학디스크드라이브 성능의 주요 척도이다. 데이터 전송률은 높을수록 좋으며, 저장용량은 되도록 큰 것이 바람직하다. 이와 같은 성능을 증가시키기 위해 광학디스크드라이브의 액추에이터는 높은 서보대역폭을 가져서 광학디스크의 진동을 보상할 수 있어야 한다. 하지만 서보대역폭은 액추에이터의 몇몇 유연모드들에 의해 제한되므로 액추에이터 유연모드의 고유진동수를 높이는 설계가 필수적이다. 이 논문은 높은 유연모드 주파수를 갖는 가동 자석형 액추에이터를 제안한다. 일반적으로 가동 자석형 액추에이터는 가동부의 형태가 단순하고, 가동부 자석이 높은 영률을 가지기 때문에 유연모드 주파수를 높이는데 유리하다. 반면 가동부의 질량이 크고 자기 회로의 효율이 좋지 않아 액추에이터의 구동감도가 나쁘다. 이와 같은 단점을 극복하는 방편으로 구동감도를 향상시키기 위해 트랙킹 방향 구동을 위한 자기회로가 폐자기회로인 모델을 설계하였다. 추가로 실험계획법을 이용한 자기회로 개선을 통해 구동감도를 향상시켰으며, 유연모드 주파수 또한 렌즈 홀더의 변경을 통해 향상시켰다.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권1호
• /
• pp.37-42
• /
• 2003

Active control of flexural vibrations of smart laminated composite beams has been carried out using piezoceramic sensor/actuator and viscoelastic material. The beams with passive constrained layer damping have been analyzed by formulating the equations of motion through the use of extended Hamilton's principle. The dynamic characteristics such as damping ratio and modal damping of the beam are calculated for various fiber orientations by means of iterative complex eigensolution method. This paper addresses a design strategy of laminated composite under flexural vibrations to design structure with maximum possible damping capacity.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.377.2-377
• /
• 2002

In optical disk drives (ODD), the demands of high data density and high speed have been increasing rapidly to achieve high data capacity and data transfer rate The use of short wavelength laser and high track following performance are needed to raise data density and data rate. For high-performance actuator, the improvement of linearity and acceleration become more important. (omitted)

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.539-546
• /
• 2004

Conventional robot manipulators actuated by motors with the speed reducer such as the harmonic drive have weakness in the load capacity, since the speed reducer does not have enough strength. To overcome this, a new type of the robot actuator based on the four-bar-link mechanism driven by the ball screw was proposed and constructed. Also, a new type of a revolute-jointed robot manipulator composed of the developed actuators was developed. The base axis is actuated by the motor with the conventional speed reducer, but the other axes are actuated by the proposed actuators. The kinematics and dynamics of the robot were analyzed, and the performance test of the robot was made. Through the test results, the performance of superior load capacity versus the robot weight is shown.

• 항공우주기술
• /
• 제13권2호
• /
• pp.160-166
• /
• 2014

액체로켓 엔진용 개폐밸브는 파일럿 공압으로 포핏을 열고 스프링 힘에 의해 닫음으로써 로켓엔진의 추진제 유량을 제어한다. 현재 개발 중인 엔진용 개폐밸브는 다이어프램 액추에이터에서 압력을 제거하면 닫히도록 설계되어 있다. 다이어프램을 설계하고 개발하기 위해 밸브가 열리고 닫히는 특성에 따라 수명을 분석할 필요가 있다. 밸브가 닫히기 시작하는 시점의 작동 유체의 압력을 결정하고, 포핏이 열리는 시점의 압력을 결정되어 힘평형이 설계되어 있다. 수명시험은 상온 유동에서 다이어프램부의 크랙에 의한 누설은 용접 부위에서 발생했다. 다이어프램 액추에이터의 작동 수명은 헬륨 파일럿 압력의 22 MPa 시험에서 61회이다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.479-483
• /
• 2006

As high-definition television(HDTV) broadcasting were generalized, there have been many researches and developments about large storage capacity and fast data transfer rate in optical disk drives(ODD). Pickup actuators must have high flexible mode frequencies and gain margins. Flexible modes are caused by the flexibility of moving parts in the actuator and a servo bandwidth is limited by them. As a result, the system becomes unstable for high-speed operations in high density reading and recording. In this paper, we suggest improved modeling method that considers the bonding layer. And, flexible mode frequency of actuator is improved by Design of Experiment of lens holder. Magnet circuit is designed considering the relation with moving part. Through improving yoke design, the magnetic flux is changed and DC tilt is reduced. Consequently, we designed actuator which has high flexible mode frequency and gain margins.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 B
• /
• pp.563-565
• /
• 1999

In this paper, we control attitude of an unstructured object with gyro actuator. It is well known that the attitude control of an object hanging with wire is not easy using usual actuators. Even though an actuator such as a fan can be used for control of the object, it is difficult to meet a desired control objectives. We, because of these reasons, make a gyro actuator with two motors. The first motor is responsible for spinning the wheel at high speed and the second motor is used to turn the inner gimbal. Applying the torque to the second motor, which results in the turn of the outer gimbal, torque about the vertical axis will be obtained while the wheel of the gyro is spinning constantly. This torque is used to control the attitude of the object attached. Gyro actuator utilize control unstructured object such as I-beam carrying by tower crane, and isolate construction workers from the dangerous environments. We derive a relationship of wheel and its motor, find a proper capacity of wheel motor in order to rotate a wheel. Through experiments of attitude control, we show to obtain desired control objectives.

• 정보저장시스템학회논문집
• /
• 제2권4호
• /
• pp.240-244
• /
• 2006

As high-definition television(HDTV) broadcasting becoming more generalized, there have been many researches and developments about a large storage capacity and a fast data transfer rate in optical disk drives (ODD). Pickup actuators must have high flexible mode frequencies and large gain margins. Flexible modes are caused by the flexibility of moving parts in the actuator and a servo bandwidth is limited by them. As a result, the system becomes unstable for high-speed operations in high density reading and recording. In this paper, we suggest improved modeling method in considering of the bonding layer. And, the flexible mode frequency of actuator is improved by Design of Experiments of lens holder. The Magnet circuit is designed considering the relation with the moving part. Through improving the yoke design, the magnetic flux is changed and the DC tilt is reduced. Consequently, we designed an actuator which has a high flexible mode frequency and a large gain margins.