• Journal of the Optical Society of Korea
• /
• v.20 no.6
• /
• pp.807-812
• /
• 2016

Transparent film heaters (TFHs) based on Joule heating are currently an active research area. However, TFHs based on an indium tin oxide (ITO) monolayer have a number of problems. For example, heating is concentrated in only part of the device. Also, heating efficiency is low because it has high sheet resistance ($R_s$). To address these problems, this study introduced hybrid layers of ITO/Ag/ITO deposited by magnetron sputtering, and the electrical, optical, and thermal properties were estimated for various thicknesses of the metal interlayer. The $R_s$ of ITO(40)/Ag/ITO(40 nm) hybrid TFHs were 5.33, 3.29 and $2.15{\Omega}/{\Box}$ for Ag thicknesses of 10, 15, and 20 nm, respectively, while the $R_s$ of an ITO monolayer (95 nm) was $59.58{\Omega}/{\Box}$. The maximum temperatures of these hybrid TFHs were 92, 131, and $145^{\circ}C$, respectively, under a voltage of 3 V. And that of the ITO monolayer was only $32^{\circ}C$. For the same total thickness of 95 nm, the heat generation rate (HGR) of the hybrid produced a temperature approximately $100^{\circ}C$ higher than the ITO monolayer. It was confirmed that the film with the lowest $R_s$ of the samples had the highest HGR for the same applied voltage. Overall, hybrid layers of ITO/Ag/ITO showed excellent performance for HGR, uniformity of heat distribution, and thermal response time.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2017.05a
• /
• pp.114.2-114.2
• /
• 2017

Transparent film heaters (TFHs) based on Joule heating are currently an active research area. However, TFHs based on an indium tin oxide (ITO) monolayer have a number of problems. For example, heating is concentrated in part of the device. Also, heating efficiency is low because it has high sheet resistance ($R_S$). Resistance of indium zinc oxide (IZO) is similar to ITO and it can be used to flexible applications due to its amorphous structure. To solve these problems, our study introduced hybrid layers of IZO/Ag/IZO deposited by magnetron sputtering, and the electrical, optical, and thermal properties were estimated for various thickness of the metal interlayer. It was found that the sheet resistance of the multilayer was mainly dependent on the thickness of the Ag layers. The $R_S$ of IZO(40)/Ag/IZO(40nm) multilayer was 5.33, 3.29, $2.15{\Omega}/{\Box}$ for Ag thickness of 10, 15, and 20nm, respectively, while the $R_S$ of an IZO monolayer(95nm) was $59.58{\Omega}/{\Box}$. The optical transmittance at 550nm for the IZO(95nm) monolayer is 81.6%, and for the IZO(40)/Ag/IZO(40nm) multilayers with Ag thickness 10, 15 and 20nm, is for 72.8, 78.6, and 63.9%, respectively. The defrost test showed that the film with the lowest RS had the highest heat generation rate (HGR) for the same applied voltage. The results indicated that IZO(40)/Ag(15)/IZO(40nm) multilayer has the best suitable property, which is a promising thin film heater for the application in vehicle windshield.

• Journal of the Korean Society of Safety
• /
• v.28 no.2
• /
• pp.60-65
• /
• 2013

On the basis of the guideline "2012-104(2012.9.26.)" notified by the ministry of employment and labor, this paper provided the baseline data and the improvement proposal in applying risk assessment to a construction site by group interview & survey of construction workers. The worker's awareness and action plan of safety and health were investigated by numerical analysis. From the result of group interview and the survey of construction workers, it was found that most of construction workers feel the danger during the work. The results also shows that risk assessment can help to change & raise the awareness of safety and to reduce the industrial disaster. In addition, simple safety management activity such as TBM & active education of safety will be necessary for safe workspace and the active TBT(tool box talk) which combines TBM & the education of safety will be also effective.

• Smart Structures and Systems
• /
• v.17 no.5
• /
• pp.691-708
• /
• 2016

Recently, number of smart material are investigated and widely used in civil construction and other industries. Present study investigates the application of smart semi-active piezoelectric friction damper (PFD) made with piezoelectric material for the seismic control of the horizontally curved bridge isolated with lead rubber bearing (LRB). The main aim of the study is to investigate the effectiveness of hybrid system and to find out the optimum parameters of PFD for seismic control of the curved bridge. The selected curved bridge is a continuous three-span concrete box girder supported on pier and rigid abutment. The PFD is located between the deck and abutments or piers in chord and radial directions. The bridge is excited with four different earthquake ground motions with all three components (i.e. two horizontal and a vertical) having different characteristics. It is observed that the use of semi-active PFD with LRB is quite effective in controlling the response of the curved bridge as compared with passive system. The incorporation of the smart damper requiring small amount of energy in addition with an isolation system can be used for effective control the curved bridge against the dynamic loading.

• Applied Chemistry for Engineering
• /
• v.8 no.1
• /
• pp.114-121
• /
• 1997

The positive active material for polymer film-battery was prepared by using polyphenlenediamine(PPD) synthesized in our lab. and 2,5-dimercapto-1,3,4-thiadiazole(DMcT) with various mixture ratio. The transference measurement of surface morphology and thermal stability of the prepared composite film was carried out by using SEM and TGA, respectively. Electrochemical property and electrical conductivity of the composite film were also measured by using cyclic voltammetry and four-probe method in dry box, respectively. The thermal stability of prepared composite film was up to $200^{\circ}C$. The electrical conductivity of the composite film increased and showed the highest value(about 3 S/cm) when doped at 0.4% $LiCIO_4$ solution. And we could confirm that DMcT was effective on reactivation of PPD through cyclic voltammogram.

• Bulletin of the Korean Space Science Society
• /
• 2005.04a
• /
• pp.129-132
• /
• 2005

This paper describes BAUSAT-2 orbital thermal analysis and preliminary design of thermal control subsystem. To design thermal control subsystem of HAUSAT-2, we have considered active & passive thermal control method based on basic theory and themal equilibrium equation. Using this result, suitable thermal control method and material have been selected. We have designed thermal control subsystem based on analysis of HAUSAT-2's thermal environments on sun synchronous orbit with altitude 650km, inclination $98^{\circ}$ and thermal distribution and range expectation of each HAUSAT-2's surface. Thermal analysis consists of system level, box level and board level analysis. We have completed system level and box level analysis. Till now, board level analysis of main heat dissipation board in progress. Thermal control subsystem has designed according to thermal analysis result. This design is to maintain all of the HAUSAT-2 components within the allowable temperature limits. In future, STM

• Korean Security Journal
• /
• no.1
• /
• pp.175-208
• /
• 1997

I study the actual condition and the problem of the crime prevention system of two seoul police station. that is operated on the unit of police box, and present the new improvement. Stragic and active is the new crime prevention system that introduces a concept of community oriented policing, the tendency of a developed country police. I present a medium - sized police station where 250${\sim}$300 policemen work. It consist of a patrol division, a community division and a administration support division. The chief of police bears the responsibility only for crime prevention service by concentrating on pure Patrol - centered crime prevention activity and community relation activity. Next I present a police inspector system. The most important on this paper is the community policing officer system that a policeman bears responsibility on district apart from a patrol division and support a police service related community. To be operated these systems effectively, these need to be regulated according to a police distinct, a police purpose and it's demand. Also a scale, function, authority of a existing. Police station must be regulated and the police training must be carried out.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.218-220
• /
• 1996

A composite films were prepared by using Polyphenylenediamine(PPD) synthesized in our lab. and crystalline V$_2$O$_{5}$ in various mixture ratio for using positive active material of polymer film battery. The thermal stability of prepared composite film was carried out by using TGA. Electrical conductivity of composite film were also measured by using four-probe method in dry box. The thermal stability of prepared composite film is more than 35$0^{\circ}C$. The electrical conductivity of composite film increased and showed the highest value(about 23 S/cm) when doped at 0.4% LiCiO$_4$solution.n.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.105-108
• /
• 1996

The positive active material for polymer film battery was prepared by using Polyphenylenediamine(PPD) synthesized in our lab. and 2.5-dimercapto-1, 3, 4-thiadiazole(DMcT) in various mixture ratio. The transference measurement of surface morphology and thermal stability of prepared composite film was carried out by using SEM and TGA, respectively. Electrocyhemical property and electrical conductivity of composite film were also measured by using cyclic voltammetry and four-probe method in dry box, respectively. The thermal stability of prepared composite film is more than 20$0^{\circ}C$. The electrical conductivity of composite film increased and showed the highest value(about 3 S/cm)when doped at 0.4% LiClO$_4$solution. And we could confirm that DMcT effect on reactiviation of PPD through cyclic voltammogram.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.29 no.6
• /
• pp.1259-1270
• /
• 2019

The upper bound of differential characteristic probability is mainly used to determine the number of rounds when constructing a block cipher. As the number of rounds affects the performance of block cipher, it is critical to evaluate the tight upper bound in the constructing process. In order to calculate the upper bound of differential characteristic probability, the previous searching methods for minimum number of active S-boxes constructed constraint equations for non-linear operations and linear operations, independently. However, in the case of BOGI design strategy, where linear operation is dependent on non-linear operation, the previous methods may present the less tight upper bound. In this paper, we exploit the properties of BOGI strategy to propose a new method to evaluate a tighter upper bound of differential characteristic probability than previous ones. Additionally, we mathematically proved the validity of our method. Our proposed method was applied to GIFT-64 and GIFT-128, which are based on BOGI strategy, and the upper bounds of differential characteristic probability were derived until 9 round. Previously, the upper bounds of differential characteristic probability for 7-round GIFT-64 and 9-round GIFT-128 were 2^-18.395 and 2^-26.885, respectively, while we show that the upper bounds of differential characteristic probability are more tight as 2^-19.81 and 2^-28.3, respectively.