• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.2
• /
• pp.87-94
• /
• 2023

As the latest weapon systems and electronic equipments are increasingly demanding stealth technology to improve the survivability of allies, it is necessary to implement low-observability technology that reduces the radar cross section(RCS). In order to implement this stealth technology, a method for low RCS characteristics by applying a shape design or a electromagnetic wave absorber is widely used. However, active phased array antennas have structural limitations in shape design, also when a absorber is applied to it, the performance of the antenna is degraded. Therefore, in this paper, in order to realize the low RCS characteristics of the active phased array antenna operating in the X-band, individual radiating elements suitable for applying the radio wave absorber were selected, and a 13x13 array antenna was designed and manufactured. Next, by comparing the measured results of the relative RCS and electrical performance for the manufactured antenna according to the presence and type of the absorber, it is shown that the electrical performance is maintained at an equal or higher level while obtaining the low RCS characteristics. Thereby the method proposed in this paper for implementing the low RCS characteristics was validated. Finally, it was confirmed that when the wave absorber is applied to the array antenna, the limitation of its performance deterioration can be overcome.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.2
• /
• pp.143-152
• /
• 2019

In this paper, we described the design of Ka-band planar active phased array antenna which is applicable for small RADAR for airborne and seeker of guided missile. The antenna consists of about 1000 array radiating elements and is designed to be within 200mm diameter. We optimized the spacing of radiating elements to allow beem steering above ${\pm}55$ degrees of Field of view, and analyzed the performance of antenna. We confirmed that the Effective Isotropic Radiated Power (EIRP) of the antenna can be 94.22 dBm and receive G/T can be 1.68 dB/k through the designs of RF components and the verification of RF budget. The TX output of TR Module is designed to be over 1.3W for EIRP, and Receive noise figure of TR Module is designed to be less than 5dB for G/T.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1243-1251
• /
• 2009

This paper presents design and test results of X-Band Transmit/Receive(T/R) module for active phased-array radar. Active phased array radars typically require solid state T/R modules with high output power, low noise figure, high Third Order Intercept(TOI), and sufficient gain in both transmit and receive. The output power of the module is 9 watts over a wide bandwidth. The noise figure is as low as 2.8 dB. Phase and amplitude are controlled by the 6-bit phase shifter and 5-bit attenuator, respectively. Highly integrated T/R module is achieved by using LTCC(Low Temperature Co-fired Ceramic) multiple layer substrate. The module incorporates a compact digital interface, requires only three supply voltages.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.407-416
• /
• 2021

An active phased array antennas can not only electrically steer the beam by controlling the weighting of the excitation signal, but can also form a pattern null in the direction of the interference source. The weight of the excitation signal to steer the main beam can be easily calculated based on the position of the radiating element. In addition, the weight of the excited signal for pattern null formation can also be calculated by setting the required radiation pattern and using WLSM(Weighted Least Squares Method). However, in a general wireless communication network environment, the location of the interference source is unknown. Therefore, an adaptive pattern null synthesis is needed. In this paper, it was confirmed that pattern null synthesis according to the required radiation characteristic was possible. And based on this, adaptive pattern null synthesis into the direction of an interference source was studied using a binary search algorithm based on observation area. As a result of conducting a simulation based on the presented technique, it was confirmed that adaptive pattern null forming into the direction of an interference is possible in efficient way.

• Smart Media Journal
• /
• v.9 no.4
• /
• pp.60-65
• /
• 2020

The monopulse tracking algorithm can estimate the location of a partner station based on an RF (Radio Frequency) signal. The location of the partner station is estimated based on the monopulse ratio curve (MR-C), which is calculated based on the sum and difference signal patterns of an antenna. Therefore, the range in which the estimated location can be calculated with high accuracy increases in proportion to the linear region of MR-C. In this paper, we proposed a method to extend the linear region of the MR-C curve using the beamforming technique for the tracking antenna system using the active phased array antenna. Simulation results based on the same antenna system, it was confirmed that the linear region of MR-C was enlarged by about twice as much as the general case where the proposed method was not applied.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.378-385
• /
• 2013

An S-band multifunction chip with a simple interface for an active phased array base station antenna for next-generation mobile communications is designed and fabricated using commercial 0.5-${\mu}m$ GaAs pHEMT technology. To reduce the cost of the module assembly and to reduce the number of chip interfaces for a compact transmit/receive module, a digital serial-to-parallel converter and an active bias circuit are integrated into the designed chip. The chip can be controlled and driven using only five interfaces. With 6-bit phase shifting and 6-bit attenuation, it provides a wideband performance employing a shunt-feedback technique for amplifiers. With a compact size of 16 $mm^2$ ($4mm{\times}4mm$), the proposed chip exhibits a gain of 26 dB, a P1dB of 12 dBm, and a noise figure of 3.5 dB over a wide frequency range of 1.8 GHz to 3.2 GHz.

• ETRI Journal
• /
• v.27 no.3
• /
• pp.243-249
• /
• 2005

A mobile antenna for multimedia communications with Ku-band geostationary satellite KOREASAT-3 and JSAT-2A is presented. The forward link of the satellite communication is 11.7 to 12.75 GHz, and the return link is 14.0 to 14.5 GHz. The mobile antenna is designed to be a stair structure using 24 active phased array elements in order to provide a low profile, and to be at a non-periodic array distance using the genetic algorithm. Also, the designed antenna uses the double beam forming method for stable satellite tracking. The fabricated mobile antenna is examined using various experiments to confirm its capability for practical application. From the measured results, the fabricated mobile antenna system is confirmed to have a good performance.

• Journal of electromagnetic engineering and science
• /
• v.19 no.2
• /
• pp.107-114
• /
• 2019

Alert-confirm detection is a highly efficient method to improve phased array radar search performance. It comprises sequential detection in two steps: alert detection, in which a target is detected at a low detection threshold, and confirm detection, which is triggered by alert detection with a longer dwell time to minimize false alarms. This paper provides a design method for applying the alert-confirm detection to multifunctional radars. We find optimum dwell times and false alarm probabilities for each alert detection and confirm detection under the dual constraints of total false alarm probability and maximum allowable dwell time per position. These optimum values are expressed as a function of the mean new target appearance rate. The proposed alert-confirm detection increases the maximum detection range even with a shorter frame time than that of uniform scanning.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.10
• /
• pp.1061-1070
• /
• 2009

In this paper, we have designed TDL(True-time Delay Line) for eliminating beam-squint occurring in active phased array antenna with large electrical size operated in wide bandwidth, and have tested its electrical performance. The proposed TDL device is composed of 4-bit microstrip delay line structure and MMIC amplifier for compensation of the delay-line loss. The measured results of gain and phase versus delay state satisfy the electrical requirements, also P1dB output power and noise figure meet the requirement. To verify the performance of fabricated TDL, we have simulated the beam patterns of wide-band active phased array antenna using the measured results and have certified the beam pattern compensation performance. As a result of simulated beam pattern compensation with respect to the 675.8 mm size antenna which is operated in X-band, 800 MHz bandwidth, we have reduced the beam squint error of ${\pm}1^{\circ}$ with ${\pm}0.1^{\circ}$. So this TDL module is able to be applied to active phase array antenna system.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.4C no.6
• /
• pp.306-309
• /
• 2004

This paper presents a new active antenna consisting of a microstrip patch for the passive radiator, a mixer for frequency conversion, a voltage controlled oscillator (VCO) and a phase detector for phase control. The microwave signal frequency has been converted into intermediate frequency (IF) on the antenna elements by the mixer. The active antenna consists of two ports, the IF port has a transmitted IF signal via power combined to the baseband and the dc control port is under the control of the phase-detector. The input voltage of the VCO is controlled by the phase detector. The scan range of the array is determined by the phase detector and the VCO and is obtained between 30$^{\circ}$ and - 30$^{\circ}$