• 분석과학
• /
• 제30권5호
• /
• pp.234-239
• /
• 2017

화재 현장에서 완전 연소하지 않은 잔류물의 성분을 규명하는 것은 화재 원인을 추적하는 중요한 단서가 된다. 화재 현장에서 많이 발견되는 플라스틱 연소 잔류물의 종류를 규명하기 위하여 폴리에틸렌 (Polyethylene, PE) 수지와 Acrylonitrile butadiene styrene (ABS) 수지의 연소 후 잔류물에 관한 연구를 진행 하였다. 콘 칼로리미터 (Cone calorimeter)를 사용하여 플라스틱 시료를 200, 300, 350, 400, $500^{\circ}C$로 각각 3분 동안 연소시킨 후 변화된 무게와 연소생성물을 얻었다. 각 온도에서 얻어진 연소생성물을 동결 건조 후 분쇄한 분말 시료를 FT-near infrared (NIR) spectrometer로 스펙트럼을 측정 하였다. 폴리에틸렌 수지 시료를 연소시켰을 때 $350^{\circ}C$까지는 무게의 변화가 없었으나 $400^{\circ}C$ 이상에서는 급격한 무게의 변화를 측정 할 수 있었다. 각 온도에서 얻어진 폴리에틸렌 수지 및 ABS 수지 시료의 FT-NIR 측정 스펙트럼을 주성분 분석(Principle component Analysis, PCA)를 통해서 연소 잔유물이 폴리에틸렌과 ABS 지임을 확인할 수 있었다. 따라서 근적외선 분광법으로 화재현장에서 발견되는 불연소 플라스틱의 종류를 신속하게 확인할 수 있었다.

• 한국산학기술학회논문지
• /
• 제14권11호
• /
• pp.5352-5356
• /
• 2013

최근 플라스틱 성형품은 기능적인 측면뿐만 아니라 디자인 및 광택과 같이 시각적으로 즉각 식별이 가능한 부분에 까지 많은 관심과 주의를 기울이고 있다. 이와 관련하여 성형품 광택의 제어를 위하여 성형조건이 광택에 미치는 영향에 대한 연구가 필요하지만 관련 연구는 아직 충분히 이루어지지 않고 있다. 따라서 본 연구는 플라스틱 성형품의 외관에 주로 사용되는 ABS (Acrylonitrile-Butadiene-Styrene) 플라스틱 성형품에 대하여 사출압력, 사출속도, 보압력, 수지온도, 금형온도 등의 사출조건의 변화가 성형품의 외관 광택에 미치는 영향에 대하여 사출실험을 통하여 연구하였다. 연구 결과에서 보압력이 가장 큰 영향을 미침을 알 수 있었다. 특히, 보압력 55 - 75MPa 범위에서는 광택도가 증가하지만 그 이상 증가하면 광택이 감소하는데, 그 원인은 SEM(Scanning Electron Microscope)을 통하여 수지 내부의 고무 입자의 변형에 기인한다고 유추할 수 있었다.

• Advanced Composite Materials
• /
• 제16권2호
• /
• pp.181-194
• /
• 2007

This paper presents the mechanical properties of a composite consisting of acrylonitrile-butadiene-styrene (ABS) resin mixed with carbon fiber reinforced plastics (CFRP) pieces (CFRP/ABS). CFRP pieces made by crushing CFRP wastes were utilized in this material. Nine kinds of CFRP/ABS compounds with different weight fraction and size of CFRP pieces were prepared. Firstly, tensile and flexural tests were performed for the specimens with various CFRP content. Next, fracture surfaces of the specimens were microscopically observed to investigate fracture behavior and fiber/resin interface. Finally, the tensile modulus and strength were discussed based on the macromechanical model. It is found that the elastic modulus increases linearly with increasing CFRP content while the strength changes nonlinearly. Microscopic observation revealed that most carbon fibers are separated individually and dispersed homogeneously in ABS resin. Epoxy resin particles originally from CFRP are dispersed in ABS resin and seem to be in good contact with surrounding resin. The modulus and strength can be expressed using a macromechanical model taking account of fiber orientation, length and interfacial bonding in short fiber composites.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.592-596
• /
• 2001

A TACUB jig was applied to separate waste plastics [polystyrene (PS), acrylonitrile butadiene styrene (ABS), and polyethylene terephthalate (PET)] used in copy machine. The effect of water pulsation including amplitude and frequency on the separation performance was investigated for the feeds containing two or three plastics. Good results are obtained under suitable conditions. Grades of 99.8% PS,99.3% ABS, and 98.6% PET are recovered as the products in the upper, middle and bottom layers respectively. Based on these results, a processing plant fer recycling of plastics from scrapped copy machines is now under construction.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1582-1584
• /
• 2008

This paper reports a simple fabrication method for creating the superhydrophobic polymer surface using a plasma etching. Generally, it is necessary for the superhydrophobic surfaces to have a rough structure on surface with the composition of the low surface energy. In this study, Poly(methyl methacrylate) (PMMA), poly(ethylene terephthalate) (PET), acrylonitrile butadiene styrene (ABS) with superhydrophobic surface were fabricated using $O_2$ plasma etching and vapor deposition with the fluoroalkylsilane self-assembled monolayers. The plasma treated polymer surfaces are covered with the nano-pillar shaped structures after treatment for $1{\sim}2min$. And these samples with FOTS SAMs coating are showed the superhydrophobicity having the water contact angle of around $150^{\circ}$ and sometimes around $180^{\circ}$ depending on the treatment time. Furthermore the nanostructured polymer is transparent for the visible light.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 춘계학술대회 논문요약집
• /
• pp.221-221
• /
• 2004

플라스틱의 사출성형중 용용 수지에 가스를 주입하는 가스사출성형(Gas Assisted Injection Molding GAIM)에 의해 성형품을 만드는 생산방법은 약 30년 전부터 유럽지역을 중심으로 시작되었다 GAIN의 개발 배경은 발포성형을 대체하기 위한 공법으로 개발되었다. 발포성형은 싱크마크(sink mark) 제거, 치수안정성, 강도보강의 목적으로 사용하는 공법이지만, 가스기포가 표면으로 빠져나오고 표면에 가스 기포가 발생하여 외관부품에 부적당하며, 두께가 5-6mm이하의 성형품에는 적용할 수 없고, 성형시간이 긴 문제점을 가지고 있어 이러한 문제를 보강한 공법을 연구할 결과로 GAIM이 탄생하게 되었다.(중략)

• 한국소음진동공학회논문집
• /
• 제24권9호
• /
• pp.724-730
• /
• 2014

It is essential to control noise and vibration in various industrial fields. In the automobile industry, various plastics have been developed and replaced metallic materials in order to reduce mass and vibration effectively. In this study, we measured and analyzed the Young's moduli and the loss factors of Acrylonitrile butadiene styrene(ABS) and Polypropylene(PP). In order to solve the fundamental error to determine the two quantities, a loudspeaker was used instead of conventional electromagnetic devices to generate bending motion to the specimens and a laser vibrometer was also used in detection of vibration signal of the specimen. The measured Young's moduli and loss factors of the ABS specimen were nearly constant as the temperature($-10{\sim}60^{\circ}C$) was increased. The loss factor of PP specimen showed peak value at $20^{\circ}C$ and it means that there is glass transition for the PP specimen. Young's modulus of PP specimen was linearly decreased as the temperature was increased.

• 한국산업융합학회 논문집
• /
• 제23권3호
• /
• pp.375-380
• /
• 2020

In this study, we tried to evaluate the mechanical properties of Polycarbonate(PC) and acrylonitrile-butadiene-styrene(ABS) plastic materials, which are frequently used as parts of home appliances and machinery, when repeated impacts were applied. A repeating impact tester for this research was designed and manufactured to apply repetitive impacts. Two types of plastic were repeatedly impacted under a constant load, and a tensile test was performed on the plastic material that was impacted. The tensile strength of PC plastic materials that received impact more than 2000 times was reduced by about 45 % and elongation was reduced by about 10 % when compared to impact free specimens. On the other hand, in ABS plastic, a reduction of tensile strength of about 20 % was observed at about 2,000 impacted specimen, but at about 20,000 repetitive impacted specimen, a tensile strength decrease of about 65 % was observed. And the elongation was reduced by 10 % due to the cyclic harding behavior of the material.

• 공업화학
• /
• 제7권4호
• /
• pp.757-767
• /
• 1996

폴리(알킬아크릴레이트-g-카프로락톤) 그라프트 공중합체를 합성하였으며, 이것을 폴리카보네이트(PC)/폴리(아크릴로니트릴-부타디엔-스티렌)(ABS) 블렌드의 상용화제로 사용하였다. PC나 ABS와 비상용성인 폴리 알킬아크릴 레이트 주사슬을 갖는 그라프트 공중합체를 사용하였으며 이것을 PC/ABS의 계면에 위치시키는 것을 목표로 하였다. 그라프트 공중합체를 1중량부 포함하는 블렌드물은 충격 강도는 물론 파단 인장 강도에서 아주 향상된 값을 보였으며, 1/8인치 시편에서의 충격 강도 향상이 두드러졌다. 전자현미경에 의한 형태학적인 분석 결과 그라프트 공중합체의 존재가 좀더 매끄러운 PC/ABS 계면을 형성하게 하는 것으로 나타났다.

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.169-174
• /
• 2012

Electromagnetic interference(EMI) shielding effectiveness(SE) was investigated in of woven fabric made of epoxy/copper-nickel fabrics and nickel coated carbon fiber reinforced acrylonitrile-butadiene-styrene(ABS) composites. The coaxial transmission line method was used to measure the EMI shielding effectiveness of the composites. We designed and constructed a measuring system, consisting of a network analyzer and a device that plays the serves as a sample holder and at the same time as a transmission medium of the incident electromagnetic wave. The measurement of SE were carried out frequency range from 100MHz to 2GHz. It is observed that the SE of the composits is the frequency dependent increase with the increase in nickel coated carbon fibre volume fraction. The nickel coating with 20wt% ABS composite was shown to exhibit up to 60dB of SE. The result that nickel coated carbon fibre ABS composite can be used for the purpose of EMI shielding as well as for some microwave applications.