• Journal of the Korean Chemical Society
• /
• v.65 no.2
• /
• pp.88-92
• /
• 2021

In art painting creation, painting material is an important carrier. Acrylic as a young material has very wide applications in modern art. This study mainly analyzed the properties of acrylic material. Firstly, the emergence and development of acrylic were introduced, and then its material characteristics were analyzed. Finally, the performance embodiment of acrylic paintings was compared with oil paintings and watercolor paintings. It was found that acrylic paintings not only had some advantages of oil and watercolor paintings but also had own style characteristics; acrylic paintings also have advantages in durability and flexibility; acrylic paintings could present the characteristics that oil and watercolor paintings did not have while realizing the techniques of them. Acrylic paintings have a broad development space in art creation, which is worth further attention and promotion.

• Journal of Adhesion and Interface
• /
• v.6 no.1
• /
• pp.11-18
• /
• 2005

The capsules were prepared from a phase change material (PCM) of octadecane as a core material and melamine formaldehyde resin as a shell material. The PCM capsule size was varied in the range of $3{\sim}25{\mu}m$. The core contents and sizes of the PCM capsule, were determined by DSC and SEM, respectively. An acrylic coating material which contains butyl acrylate (BA), methyl metacrylate (MMA) and acrylic acid (AA) were synthesized by emulsion polymerization. The films were prepared from the acrylic emulsion and PCM capsules which have various capsule sizes. From the results of SEM experiment, it was observed that the PCM capsules were well dispersed inside the film and the surface of the film became less rough when the PCM capsule size was small. The swelling ratio of the films were not significantly affected by the PCM capsule size. However, the tensile strength and elongation of the films were greatly decreased with increasing the PCM capsule size.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.1
• /
• pp.52-59
• /
• 2000

In order to develop the transparent anti-static film with higher than 80% transparency to visible light, organic conductive compounds, N-methyl phenazinium 7,7,8,8-tetracyanoquinonedimethane (TCNQ) com-plex salts was synthesized and bar-coated on the polythylene terephthalate (PET) film using polymer binders. The best surface properties were obtained when acrylic binder was used. A single layer of TCNQ made of a acrylic binder showed a surface resistance of 10\ulcorner $\Omega$/ , a conductivity of 10\ulcorner S/cm, and a transparency of 75%. An optical microscopic examination revealed that the binder was first solidi-fied on the surface of PET film over which the needle-shaped TCNQ crystals were grown. An acrylic polyol coating over the TCNQ layer improved the transparency to 87%, becuase the acrylic polyol covers the surface of TCNQ crystals to reduce the surface roughness. This conductive material has thermal stability at room temperature and 4$0^{\circ}C$ over 4,000 h.

• Journal of the Korean Society for Advanced Composite Structures
• /
• v.6 no.3
• /
• pp.86-94
• /
• 2015

A series of injection and drainage test were conducted on an circular acrylic tube to investigate the pressure generated by the accumulated fill materials inside a circular acrylic tube structure. The acrylic tube was filled by means of gravity filling with a slurry material having an average water content of 700%. The water head during the filling process was 1.8m and the bottom pressure during initial filling was 20.18kPa. The recorded stress at the sides of the acrylic tube was 17.89kPa during the filling process and was reduced to 13.58kPa during the leaving process. Continuous drainage of the acrylic tube has greatly influenced the stresses around the tube structure. As the water is gradually allowed to overflow, the generated pressure at the topmost pressure sensor of the tube was reduced further to 2.17kPa. Eventually, the initially liquid state slurry material transforms into plastic state after water has dissipated and substantial soil particles are deposited in the acrylic tube. The final water content of the deposited silt inside the acrylic tube after the test was 42%. It was found that the state of stresses(geo-static earth pressures) in the acrylic tube was anisotropic rather than isotropic.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.11a
• /
• pp.133-134
• /
• 2019

As part of recent low-energy policies, thermal insulation standards for buildings are being tightened every year. The importance of external insulation methods is increasing due to the strengthening of insulation standards. Among the main materials used in the external insulation method, dry bit material is a finishing material composed of an organic binder and aggregate. When the fire occurs, the ignition of the surface part causes a direct fire on the thermal insulation material at the rear side when heat energy is concentrated. Therefore, it is important that the finishing material in dry insulation using a dry bit has a low fire spreading property in case of a fire and does not have a sustained combustion. The purpose of this study was to evaluate the fire spreadability by changing the internal fillers while using alkoxide-based acrylic emulsions, hybrid acrylic emulsions, and general acrylic emulsions in order to suppress the fire spreading properties of exterior finish materials.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.1
• /
• pp.35-41
• /
• 2020

The thin coating material used in the outer insulation finishing method is a finishing material mainly based on acrylic emulsion. In this study, the properties of silane modified acrylic emulsion and silica dispersed acrylic emulsion were evaluated. Experimental results showed that the silane modified acrylic emulsion had no significant effect on improving tensile strength, but was effective in improving the performance of adhesion strength, water absorption coefficient, and hot and cold repeat resistance. Silica-dispersed acrylic emulsions were effective in improving tensile strength, and at 10% substitution rate, they were effective in improving the performance of adhesion strength, water absorption coefficient and hot / cold resistance. Through this, it was judged that a composite emulsion capable of improving the performance of the acrylic emulsion could be prepared.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.722-727
• /
• 2001

The dynamic characteristics of Viscoelastic(VE) damper are experimentally studied. An experimental test was carried out to study the effects of frequency on the damping and stiffness of VE damper. Various cyclic loading tests are conducted. A good agreement was achieved between the experimental results and analytical model proposed by Kasai et al. Also the damping of acrylic rubber is compared with that of PNR material. It was concluded that the damping value of acrylic rubber is higher than that of PNR material.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.278-282
• /
• 1996

Electrical properties of acrylic acid and n-butyl acrylate grafted polyethylene were investicated. Charge accumulation characterist-ics of acrylic acid grafted PE are changed by graft ratio, but it remains not changed in n-butyl acrylate grafted PE. It was also observed that anti-treeing and AC breakdown strength of grafted PE were increased due to the graft ratio. The change of electrical properties of grafted PE were attributed to the polar group introduced by the graft reaction.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.3
• /
• pp.1-10
• /
• 2003

Shredded waste newspapers, waste acrylic raw fibers, and urea-formaldehyde (UF) adhesives, at 10% by weight on raw material, were used to produce recycled waste paper-waste acrylic raw fiber composite boards in laboratory scale experiments. The physical and mechanical properties of fire retardant treated recycled waste paper-waste acrylic raw fiber composite boards were examined to investigate the possibility of using the composites as internal finishing materials with specific gravities of 0.8 and 1.0, containing 5, 10, 20, and 30(wt.%) of waste acrylic raw fiber and 10, 15, 20, and 25(wt.%) of fire retardant (inorganic chemical, FR-7^®) using the fabricating method used by commercial fiberboard manufacturers. The bending modulus of rupture increased as board density increased, decreased as waste acrylic raw fiber content increased, and also decreased as the fire retardant content increased. Mechanical properties were a little inferior to medium density fiberboard (MDF) or hardboard (HB), but significantly superior to gypsum board (GB) and insulation board (IB). The incombustibility of the fire retardant treated composite board increased on increasing the fire retardant content. The study shows that there is a possibility that composites made of recycled waste paper and waste acrylic raw fiber can be use as fire retardant internal finishing materials.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2635-2641
• /
• 2012

Novel silver/salep-g-poly(acrylic acid) nanocomposite hydrogel were prepared in aqueous solution using poly(acrylic acid) grafted onto salep as a biopolymer based material. FT-IR spectra confirmed that poly(acrylic acid) (PAA) had been grafted onto salep in graft copolymerization reaction. TEM observations showed that silver nanoparticles have been uniformly dispersed in polymeric matrix. Effects of pH, acrylic acid (AA) amount and silver ion concentration on swelling capabilities were investigated. Results indicate that modifying AA and silver ion can improve swelling properties of the resultant nanocomposite hydrogel. pH response of this nanocomposite hydrogel in acidic and neutral pH made it suitable for drug delivery applications.