• Korean Journal of Heritage: History & Science
• /
• v.47 no.1
• /
• pp.164-179
• /
• 2014

The Buddhas of the Three Words in a form of arranging Bhaiṣajyaguru and $Amit{\bar{a}}bha$ at its side based on ${\acute{S}}{\bar{a}}kyamuni$ at the center is enshrined in Daeungbojeon Hall of Daeheungsa Temple located at Haenam. So far, this Buddhas of the Three Words has been known as a wooden Buddha statue. However, as a result of X-ray screening, in left/right Buddha statues excepting main Buddha, wood and molding clay layer were observed at the same time. Therefore, this study intended to observe its internal structure, grafting method and to clarify making technique of Buddha statue during Joseon era based on image information being obtained through X-ray screening of The Buddhas of the Three Words of Daeheungsa Temple. As its result, it was revealed that form of ${\acute{S}}{\bar{a}}kyamuni$ was completed by mainly grafting 5 pieces of timber and this statue shows a typical wood grafted Buddha statue during Joseon era. Form of Bhaiṣajyaguru and $Amit{\bar{a}}bha$ were completed based on molding technique by applying clay on sculpture similar to its appearance after sculpturing more than 10 pieces of timber through its grafting. In other words, internal timber is considered to play a role of its core and grafting method of timber is more close to a technique of molding Buddha statue than to that of wooden Buddha statue during Joseon era. However, clay was directly applied on timber thinly, not applying clay thickly on it after winding straw rope on wooden core and its characteristic is that its facial area was completely composed of wooden construction only. Therefore, it is hard to rule out a possibility that the original sculpturing intention of an artist might be a wooden Buddha statue but in view of the fact that a word, 'molding' was used in a record of relics buried in statue, it could be seen that this Buddha statue might have been recognized as a molding statue at the time when creation of this statue was completed. It is considered that number of case of making statue based on this technique would be more increased when more results of X-ray screening should be accumulated and if more data should be collected, it would provide a significant evidence for identifying chronological, regional aspects of making technique of Buddha statue.

• The Journal of the Petrological Society of Korea
• /
• v.28 no.2
• /
• pp.111-128
• /
• 2019

Ulleung Island is the top of an intraplate alkalic volcano rising 3200 m from sea floor in the East Sea (or Sea of Japan). The emergent 984.6 m consist of eruptive products of basaltic, trachytic and phonolitic magmas, which are divided into Dodong Basaltic Rocks, and Ulleung, Seonginbong and Nari groups. The Maljandeung Tuff in the Nari Group consists of thick pyroclastic sequences which are subdivided into 4 members (N-5, U-4, 3, 2), generating from explosive eruptions during past 18.8~5.6 ka B.P. From chemical data, the Member N-5, phonolitic in composition, is considerably enriched in incompatible elements and REE patterns with significant negative Eu anomalies. The members 4, 3 and 2 are phonolitic to tephriphonolitic in composition, and their REE patterns do not have significant Eu anomalies. In variation trend diagrams, many elements show abrupt compositional gaps between members, and gradual upward-mafic variations from phonolite to tephriphonolite within each member. It suggests a downward-mafic zonation that were evolved into phonolitic zone in the lower part to tephriphonolitic zone in upper part of magma chamber. It is supposed that the chemical stratification generated from multiple mechanisms of thermal gravidiffusion, crystal fractionation, and gradual melting and sequential emplacement. The stratified magmas were explosively erupted to generate a small caldera during short period (11 ka B.P.). Especially both members (U-3, 2) were accumulated by gradually erupting from the upper phonoltic zone to the lower tephriphonoltic zone of the stratified chamber in 8.4 ka B.P. and 5.6 ka B.P. time, respectively.

• Korean Journal of Child Education & Care
• /
• v.19 no.2
• /
• pp.177-196
• /
• 2019

Objective: This study aims to analyze research trends related to software education for young children, focusing on studies published in Korea from 2016 to 2019 March. Methods: A total of 26 research publications on software education for young children, searched from Korea Citation Index and Research Information Sharing Service were identified for the analysis. The trend in these publications was classified and examined respectively by publication dates, types of publications, and the fields of study. To investigate a means of research, the analysis included key topics, types of research methods, and characteristics of the study variables. Results: The results of the analysis show that the number of publications on the topic of software education for young children has increased over the three years, of which most were published as a scholarly journal article. Among the 26 research studies analyzed, 16 (61.5%) are related to the field of early childhood education or child studies. Key topics and target subjects of the most research include the curriculum development of software education for young children or the effectiveness of software education on 4- and 5-year-old children. Most of the analyzed studies are experimental research designs or in the form of literature reviews. The most frequently studied research variable is young children's cognitive characteristics. For the studies that employ educational programs, the use of a physical computing environment is prevalent, and the most frequently used robot as a programming tool is "Albert". The duration of the program implementation varies, ranging from 5 weeks to 48 weeks. In the analyzed research studies, computational thinking is conceptualized as a problem-solving skill that can be improved by software education, and assessed by individual instruments measuring sub-factors of computational thinking. Conclusion/Implications: The present study reveals that, although the number of research publications in software education for young children has increased, the overall sufficiency of the accumulated research data and a variety of research methods are still lacking. An increased interest in software education for young children and more research activities in this area are needed to develop and implement developmentally appropriate software education programs in early childhood settings.

• Journal of The Korean Astronomical Society
• /
• v.52 no.1
• /
• pp.11-21
• /
• 2019

Intensive Monitoring Survey of Nearby Galaxies (IMSNG) is a high cadence observation program monitoring nearby galaxies with high probabilities of hosting supernovae (SNe). IMSNG aims to constrain the SN explosion mechanism by inferring sizes of SN progenitor systems through the detection of the shock-heated emission that lasts less than a few days after the SN explosion. To catch the signal, IMSNG utilizes a network of 0.5-m to 1-m class telescopes around the world and monitors the images of 60 nearby galaxies at distances D < 50 Mpc to a cadence as short as a few hours. The target galaxies are bright in near-ultraviolet (NUV) with $M_{NUV}$ < -18.4 AB mag and have high probabilities of hosting SNe ($0.06SN\;yr^{-1}$ per galaxy). With this strategy, we expect to detect the early light curves of 3.4 SNe per year to a depth of R ~ 19.5 mag, enabling us to detect the shock-heated emission from a progenitor star with a radius as small as $0.1R_{\odot}$. The accumulated data will be also useful for studying faint features around the target galaxies and other science projects. So far, 18 SNe have occurred in our target fields (16 in IMSNG galaxies) over 5 years, confirming our SN rate estimate of $0.06SN\;yr^{-1}$ per galaxy.

• Korean Journal of Heritage: History & Science
• /
• v.42 no.1
• /
• pp.144-157
• /
• 2009

Nondestructive methods to check the vitality of trees and to find out internal decay of old-giant trees include the use of electrical resistance, ultrasound transmission time, microdrilling, and infrared thermography etc. Among these, ultrasound transmission offers some advantages compared to others such as it is an entirely nondestructive detection method and it can be applied to very big trees. However, the ultrasound equipment is comparatively expensive and not broadly spread yet. On the other hand, Shigometer is versatile to be applied to check vitality of the tree and find out internal decay. Electrical conductivity of plant tissues is a very useful characteristics to determine the vitality and internal decay of trees. Electrical resistance of cambial area tells about the vitality of a tree and electrical resistance of heartwood reveals discoloration or decay of it. For determination of the vitality of the tree, the standard equation for calibration of measured electrical resistances should be developed by measuring and analyzing electrical resistance from at least 30-40 trees of the same species with that tree. All the factors, especially tree species, diameter of the stem, and temperature, which can altered the electrical resistance of trees, should be taken into consideration in the development of the equation. If the standard equation is developed for old-giant trees that we should conserve, it will be very useful. In addition, periodical and continued measuring of a certain tree will help to determine the condition of the tree by comparing the measurement with accumulated data of the tree. Measuring electrical resistance of wood might not require the standard equation. But it also needs to check electrical resistance of sound wood of the same tree species. If the stems that should be examined is thicker than 40cm, it is better to use the ultrasound measurement combined to Shigometer.

• The Journal of Engineering Geology
• /
• v.29 no.2
• /
• pp.85-97
• /
• 2019

It can be observed that steep slopes ($65^{\circ}$ to $80^{\circ}$) consist of rock masses were kept stable for a long time. In rock-mass slopes with similar ground condition, steeper slopes than 1 : 0.5 ($63^{\circ}$) may be applied if the discontinuities of rock-mass slope are distributed in a direction favorable to the stability of the slope. In making a decision the angle of the slope, if the preliminary rock mass conditions applicable to steep slope are quantitatively setup, they may be used as guidance in design practice. In this study, the above rock mass was defined as a good continuum rock mass and the quantitative setup criterion range was proposed using RMR, SMR and GSI classifications for the purpose of providing engineering standard for good continuum rock mass conditions. The methods of study are as follows. The stable slope at steep slopes ($65^{\circ}$ to $80^{\circ}$) for each rock type was selected as the study area, and RMR, SMR and GSI were classified to reflect the face mapping results. The results were reviewed by applying the calculated shear strength to the stable analysis of the current state of rock mass slope using the Hoek-Brown failure criterion. It is intended to verify the validity of the preliminary criterion as a rock mass condition that remains stable on a steep slope. Based on the analysis and review by the above research method, it was analyzed that a good continuum rock mass slope can be set to Basic RMR ${\geq}50$ (45 in sedimentary rock), GSI and SMR ${\geq}45$. The safety factor of the LEM is between Fs = 14.08 and 67.50 (average 32.9), and the displacement of the FEM is 0.13 to 0.64 mm (average 0.27 mm). This can be seen as a result of quantitative representation and verification of the stability of a good continuum rock mass slope that has been maintained stable for a long period of time with steep slopes ($65^{\circ}$ to $80^{\circ}$). The setup guideline for a good continuum rock mass slope will be able to establish a more detailed setup standard when the data are accumulated, and it is also a further study project. If stable even on steep slopes of 1 : 0.1 to 0.3, the upper limit of steep slopes is 1 : 0.3 with reference to the overseas design standards and report, thus giving the benefit of ensuring economic and eco-friendlyness. Also, the development of excavation technology and plantation technology and various eco-friendly slope design techniques will help overcome psychological anxiety and rapid weathering and relaxation due to steep slope construction.

• Korean Journal of Breeding Science
• /
• v.50 no.4
• /
• pp.442-452
• /
• 2018

In this study, we analyzed the growth characteristics and isoflavone content of 43 soybean varieties highly adaptable to highland areas. The flowering period of each cultivation zone was from July 15 to August 12 at Daewallyeong, from July 18 to August 11 at Jinbu, and from July 23 to August 13 at Gangneung. The accumulated temperature from flowering to maturity was $1,297^{\circ}C$ for Daegwallyeong, $1,391^{\circ}C$ for Jinbu, and $1,685^{\circ}C$ for Gangneung. Forty-three varieties were classified into four utilities; soy sauce and tofu, bean sprouts, cooking with rice, and vegetable and early maturity. The content of isoflavone was highest at $2,579{\mu}g/g$ in varieties for soy sauce and tofu usage. Five varieties ("Paldalkong," "Sinpaldal2," "Ilmikong," "Sinpaldalkong," and "Daepung") cultivated in Daegwallyeong had over $4,000{\mu}g/g$ of isoflavone. The isoflavone content of the region Daegwallyeong was different at the significance level of 0.1 (p=0.061) compared to Gangneung. There was no significant difference between Gangneung and Jinbu. It is thought that the low temperature of the maturation stage during the growing period affected isoflavone accumulation. The varieties with more than $3,000{\mu}g/g$ of isoflavone content in Daegwallyeong, Jindu, and Gangneung were "L29," "Williams82," "Ilmikong," and "Daepung." These were genetically and environmentally stable in isoflavone content. It is expected that this study will be used as basic data for the functional breeding and selection of soybean varieties highly adaptable to a specific region, and to help expand soybean cultivation areas in highlands.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.16 no.6
• /
• pp.131-144
• /
• 2021

The organizational ambidexterity is an organizational strategy designed to pursue exploration activities to seize new opportunities and exploitation activities to efficiently use resources. Most of these ambidextrous structures have been studied for large corporations with slack resources, and there are still not many studies on the necessity of an ambidextrous structure for startups with relatively low-level resources. However, recently, the startup ecosystem is being advanced globally, and the amount of VC investment is rapidly increasing. This is a time when a lot of venture fund is invested in startups and a startup-friendly environment for rapid growth is created. This is the time to discuss the necessity and applicability of an ambidextrous organizational structure for startups. Therefore, this study conducted a hypothesis test whether the importance and necessity of balance that startups solving market problems with new ideas and utilizing accumulated resources have. To conduct this study, we analyzed 140 startups data gathered from the survey and the moderation effect was also analyzed. As a result of the study, it was verified that the balance of startup exploration and exploitation had a significant effect on startup performance, and the moderating effect of environmental dynamics was found to have a significant effect on the relationship with non-financial performance. Therefore, for startups with insufficient resources, it was concluded that the surplus resources generated in the process of a firm's growth should be effectively utilized and the balance between exploration and exploitation should be balanced from the initial stage of searching for a new business. In other words, it was confirmed that it is important for continuous growth and survival to seek the structure of an ambidextrous organization in order to internalize a mechanism that enables startups to pursue both effectiveness and efficiency in the long term. This study suggests a strategic direction for the growth of startups from the perspective of organizational structure. We expect that this meaningful results on the relationship between the ambidextrous capabilities of startups and performance contribute to the growth of startups in the rapidly growing startup venture environment.

• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.334-346
• /
• 2022

There is a lack of knowledge and information on the understanding and application of the Process Safety Management (PSM) system, recognized as a major cause of industrial accidents in small-and medium-sized workplaces. Hence, it is necessary to prepare a protocol to secure the practical and continuous levels of implementation for PSM and eliminate human errors through tracking management. However, insufficient research has been conducted on this. Therefore, this study investigated and analyzed the various violations in the administrative measures, based on the regulations announced by the Ministry of Employment and Labor, in approximately 200 small-and medium-sized PSM workplaces with fewer than 300 employees across in korea. This study intended to contribute to the prevention of major industrial accidents by developing a facility maintenance web program that removed human errors in small-and medium-sized workplaces. The major results are summarized as follows. First, It accessed the web via a QR code on a smart device to check the equipment's specification search function, cause of failure, and photos for the convenience of accessing the program, which made it possible to make requests for the it inspection and maintenance in real time. Second, it linked the identification of the targets to be changed, risk assessment, worker training, and pre-operation inspection with the program, which allowed the administrator to track all the procedures from start to finish. Third, it made it possible to predict the life of the equipment and verify its reliability based on the data accumulated through the registration of the pictures for improvements, repairs, time required, cost, etc. after the work was completed. It is suggested that these research results will be helpful in the practical and systematic operation of small-and medium-sized PSM workplaces. In addition, it can be utilized in a useful manner for the development and dissemination of a facility maintenance web program when establishing future smart factories in small-and medium-sized PSM workplaces under the direction of the government.

• Journal of Korean Society of Forest Science
• /
• v.111 no.4
• /
• pp.473-481
• /
• 2022

Environment-friendly harvesting is practiced to maintain ecosystem, landscape, and forest protection functions. The present study was conducted at Simgok-ri, Sinbuk-myeon, Pocheon, Gyeonngi-do, where a 41-50-year-old Japanese larch forest was harvested in an environment-friendly manner from 2017 to 2019. The dynamics of organic matter in this forest were investigated at three years after the harvest. Specifically, organic matter content was measured on the forest floor and in overstory biomass, litterfall, and soil up to 30 cm in depth from June 2020 to January 2021. Owing to the harvest, the amount of overstory biomass of the Japanese larch stands decreased from 142.22 to 44.20 t ha^-1. On the forest floor, the amount of organic matter was 32.87 t ha^-1 in the control plots and 23.34 t ha^-1 in the harvest plots. Annual litterfall was 4.43 t ha^-1 yr^-1 in the control plots and 1.16 t ha^-1 yr^-1 in the harvest plots. Soil bulk density in the B horizon was 0.97 g cm^-3 in the control plots and 1.06 g cm^-3 i n the harvest plots. Soil organic matter content was 11.5% in the control plots and 12.8% in the harvest plots. The total amount of soil organic matter did not differ significantly between the control plots (245.21 t ha^-1) and harvest plots (263.92 t ha^-1), although the amount of soil organic matter tended to be higher in the harvest plots. The total amount of organic matter in the forest was estimated to be 406.48 t ha^-1 in the control plots and 338.21 t ha^-1 in the harvest plots. In the harvest plots, the ratio of aboveground organic matter decreased to 13.1% and soil organic matter increased to 78.0%, indicating that the distribution of organic matter changed significantly in these plots. Overall, the carbon accumulated in aboveground biomass was substantially reduced by environment-friendly harvesting, whereas the soil carbon level increased, which played a role in mitigating the reduction of system carbon in the forest. These results highlight one possible resolution for forest management in terms of coping with climate change. However, given that only three years of environment-friendly harvesting data were analyzed, further research on the dynamics of organic matter and tree growth is needed.