• Wind and Structures
• /
• v.27 no.4
• /
• pp.223-234
• /
• 2018

In this study, a simplified three-dimensional calculation model is developed for the dynamic analysis of soil-pile group-supertall building systems excited by wind loads using the substructure method. Wind loads acting on a 300-m building in different wind directions and terrain conditions are obtained from synchronous pressure measurements conducted in a wind tunnel. The effects of soil-structure interaction (SSI) on the first natural frequency, wind-induced static displacement, root mean square (RMS) of displacement, and RMS of acceleration at the top of supertall buildings are analyzed. The findings demonstrate that with decreasing soil shear wave velocity, the first natural frequency decreases and the static displacement, RMS of displacement and RMS of acceleration increase. In addition, as soil material damping decreases, the RMS of displacement and the RMS of acceleration increase.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.9
• /
• pp.731-740
• /
• 2014

Occupants induced floor vertical vibrations may cause other occupant's annoyance and lead to social loss. To help control such floor vibrations, several criteria have been developed mostly based on human perception tests and floor vibration tests. Floor vibration is evaluated by comparison with criteria and vibration parameters of subject floor, such as frequency, damping ratio, acceleration value, vibration duration time and occurrence frequency. Three acceleration value parameters are used in criteria; peak acceleration, rms acceleration and VDV, when a floor vibration serviceability is evaluated. Meanwhile rms acceleration and peak acceleration are adopted as vibration limit value in criteria and researches of human perception for vibration. Occupants induced floor vibration is transient rather than steady state. However, rms acceleration is not reliable parameter for evaluating transient vibration. The objective of this study is to investigate the characters of human perception level according to acceleration value parameters for vibration induced by heel impacts and walking activities.

• Korean Journal of Applied Biomechanics
• /
• v.20 no.2
• /
• pp.191-196
• /
• 2010

The purpose of this study was to investigate the effect of gait speed and walkway slope on the body acceleration, for the future validation of using an accelerometer in the estimation of energy consumption. Ten young healthy subjects with accelerometers on the upper thigh and ankle walked on a treadmill at 9 conditions(three speeds ${\times}$ three slopes) for 5 minutes. Acceleration signals of four directions, i.e. anterior-posterior(AP), medio-lateral(ML), superior-inferior(SI) and vector sum(VS) directions, of each sensor were measured, and root means squared(RMS) values of them were used as analysis variables. As statistical analysis, repeated measure two-way ANOVA was performed for RMS accelerations at each attachment sites, with slope and velocity as independent factors. At both the upper thigh and ankle, RMS acceleration of all directions were affected by gait velocities(p<.001) showing greater accelerations for higher velocities. Contrary to expectations, no slope effect existed in RMS accelerations at hip. Moreover, RMS acceleraion at ankle decreased with slope in SI and VS directions(p<.01). These results suggests that RMS acceleration cannot reflect the change in physical activity due to the change in walkway slope.

• International Journal of Railway
• /
• v.2 no.4
• /
• pp.152-163
• /
• 2009

In this paper, the correlation between the accelerations measured at the track components and the parameters affecting the acceleration is analyzed. To do it, the accelerations of each track component such as rails, sleepers and ballast are measured in Kyong-Bu high-speed Line. The RMS values of the measured accelerations are calculated and the pad stiffness, the longitudinal irregularity, running velocity and the corrugation, are considered as the parameters affecting the acceleration. By using the linear regression, the correlation coefficients are calculated to analyze the relationship between the acceleration characteristics and the parameters. Also, the 1/3 Octave analysis is calculated to analyze the dominant frequency band of the accelerations of the track components.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.03a
• /
• pp.238-246
• /
• 2003

By using simulated ground motions, which is sum of earthquake signals and noise, we measured the distortion of response spectra due to noise. We found that the distortion is more closely related to the signal-to-noise (S/N) ratio of root-mean-square (RMS) measurement than that of conventional peak measurement. Given a S/M ratio, the distortion of absolute acceleration response spectra is independent on the earthquake magnitude, while that of relative displacement response spectra has a strong dependence on the earthquake magnitude. This means that, when we calculate response spectra from time histories, we can efficiently predict the distortion of acceleration response spectra simply by measuring the RMS SJN ratios, or the distortion of displacement response spectra by combining the RMS S/N ratios and the earthquake magnitudes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1315-1321
• /
• 2013

This study presents a prognostic technique for the damage state of a ball bearing. A stochastic bearing fatigue defect-propagation model is applied to estimate the damage progression rate. The damage state and the time to failure are computed by using RMS data from noisy acceleration signals. The parameters of the stochastic defect-propagation model are identified by conducting a series of run-to-failure tests for ball bearings. A regularized particle filter is applied to predict the damage progression rate and update the degradation state based on the acceleration RMS data. The future damage state is predicted based on the most recently measured data and the previously predicted damage state. The developed method was validated by comparing the prognostic results and the test data.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.11 no.1
• /
• pp.17-24
• /
• 2005

During handling unitized products, they are subjected to a variety environmental hazards. Shock and vibration hazards are generally considered the most damaging of the environmental hazards on a product, and it may encounter while passing through the distribution environment. A major cause of shock damage to products is drops during manual handling. The increasing use of unitization on pallets has been resulted in a reduction in the manual handling of products and with it a reduction in the shock hazards. This has caused and increasing interest in research focused on vibration caused damage. the use of pallets as a base for unitizing loads, aids in the mechanical handling, transportation and storage of products. Besides aiding in the handling, transportation and storage of products, a pallet also acts on and interface between the packaged goods and the distribution environment. The determination of the impact deformation of the cushioning materials such as tray cup (polymeric foam) and corrugated fiberboard pad must be carried out to design the proper packaging system providing adequate protection for the fruit, and to understand the complex interaction between the components of fruit when they relate to expected transportation vibration inputs. In this study, the theoretical analysis of impact deformation for cushioning materials by dynamic vibration. The impact deformations of SW and DW corrugated fiberboard pad in acceleration amplitudes of 0.25 G-rms and 0.5 G-rms that were usually generated in transport vehicles during distribution environments were very small compare with the thickness of corrugated fiberboard pad. The maximum of vibration acceleration level of tray cup by vibration impact was about 3.2 G-rms. The theoretical allowable acceleration (G-factor) of the pear was 0.7102 G-rms, and the maximum dynamic deformation estimated within G-factor was about 1 mm.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.10
• /
• pp.60-67
• /
• 2019

Recently, lightweight materials such as Ti alloys have been used increasingly in the aerospace and high-tech industries for weight loss and fuel efficiency. Because of built-up edges and workpiece deflection due to low stiffness, the Ti alloys have poor machinability. In our study, systematic experiments were conducted to investigate the milling characteristics of the Ti alloy (Ti-6A1-4V) with endmills. The independent variables in the experiment were spindle speed, feed per tooth, and axial depth. Cutting force, acceleration RMS, and surface roughness were measured. Using the response surface method, the optimal cutting conditions were analyzed to improve machining quality and productivity.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.7
• /
• pp.549-555
• /
• 2008

Analytical method to analyze the tolerance effect on the vehicle ride comfort is suggested in this paper. Ride comfort is one of the most important performance indices which decide the vehicle design quality. In general, the ride comfort is affected by the variations of parameters of a vehicle model. Therefore, the effects of the parameters on the ride comfort need to be evaluated statistically based on the whole-body vibration of the vehicle. In this paper, weighted RMS values of the acceleration PSD of a seat position are used to define the ride comfort. The equations of motion and the sensitivity equations are derived based on a 5-DOF vehicle model. By employing the sensitivity information of the acceleration at the seat position, the tolerance effect on the vehicle ride comfort could be effectively analyzed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.466-471
• /
• 2003

In order to analyze linear motor driven feed system, preliminary studies have been conducted focusing on the performance evaluation of the system based on the various combination of control gain along with acceleration. Tentative simulation revealed that due to the complexity of control system reduced number of control condition is recommended. Actual machining process with conventional feed system using endmill tool was employed as a preliminary study. Several sensing methods including AE, acceleration sensors and tool dynamometer were used. Results revealed the consistency in AE and cutting resistance. There were inconsistent empirical results in accelerometer probably due to the insensitivity of the sensor signal with respect to the experimental system