• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.11
• /
• pp.501-509
• /
• 2019

The construction of foundation piles for buildings and bridges is changing from pile driving to an injected precast pile method. The goal is to minimize environmental damage, noise pollution, and complaints from neighboring residents. However, it is necessary to develop economic piles that are optimized for precasting by a centrifugal method in terms of both the material and structural system. A reinforced joint method is proposed for reinforced concrete piles (RC piles) manufactured by centrifugal casting. A previous study concluded that the structural performance of the current joint system for RC piles could be improved by using a reinforced joint composed of extended circular band plates and studs. In this study, the structural performance of such a joint was validated experimentally by bending and shear strength measurements. The proposed joint reinforcement method showed adequate structural performance in terms of bending and shear strength. The overall load-deflection behavior is close to that of a structure without joints, so it is expected that the behavior and performance of the design can be reliably reflected in site structures.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.12
• /
• pp.3546-3552
• /
• 2009

In this study, an analysis code was created for a 190*650*25-mm (W*H*D) parallel-flow evaporator, and research was done on how to increase the heat transfer rate of aluminum PF heat exchanger for application in IDU. After varying the R410A refrigerant up-down flow to two and three passes and the distribution ratio to 1:1:1 and 1:2:2, it was determined that the two-pass flow has a 30% higher partial heat transfer rate and a 25% lower heat transfer coefficient compared to the three-pass flow. As for the distribution ratios of the three-pass flow, 1:1:1 was found to have a lower refrigerant pressure loss than 1:2:2 distribution. It was assumed, though, that the refrigerant distribution had a uniform flow and that its value was thus overestimated in the actual case of maldistribution in each pass.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.153-159
• /
• 2018

In recent years, the development of weapons systems in the field of defense research and development has become increasingly large, complex, and long-term, and so have budgets and the time spans involved. In order to improve this, the Weapon Systems Requirement Verification Committee, which benchmarked the preliminary feasibility of the private sector, was established to verify the appropriateness of requirements, and the necessity and priority of the projects. This research proposes a methodology for analyzing and prioritizing proposed weapons systems for effective and strategic allocation of defense budget funding. First, the evaluation factors that can be used in the defense sector were assessed by analyzing the related fields. We set the weighting of items by using the analytical hierarchy process for technical risk assessment and technical profitability evaluation. After that, we applied the methodology to 32 weapons systems and analyzed the results. In conclusion, through this study, it was possible to analyze profitability dimensions overlooked in the existing methodology.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.4
• /
• pp.747-752
• /
• 2009

In this paper, the MIMO(Multi-Input Multi-Output) channel characteristics for Rx antenna spacing are described in the real environment, which has LOS(Ling of Sight) and NLOS (Won-Line of Sight). We developed $2\times2$ MIMO channel measurement system at 2.3GHz Wibro Band. MIMO antenna evaluation parameters such as received power, channel capacity and spatial correlation are evaluated for standard dipole antenna with 0.25, 0.5, 0.75 and 1.0 wavelength spacing at 2-position for LOS and 4-position for NLOS. The spatial correlation is distributed more than 0.9 in most LOS case which might be intricate to operate MIMO communication. MIMO antenna design need to be focused on getting spatial diversity and reducing spatial correlation in LOS case.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.9
• /
• pp.5502-5512
• /
• 2014

Until recently, Integrated Logistics Support (ILS) focused mainly on the development and acquisition of supportability factors (maintenance planning, maintenance tools, support equipment, supply support, maintenance training, etc.). In the long term, supportability strategies and policies are needed in terms of LEAN-like cost reduction, efficiency in the field of weapon systems. This study first introduces the concept of Lean, theory of Lean Maintenance and suggests Lean maintenance framework, maintenance strategy for ILS. The case studies were analyzed in terms of the maintenance time, maintenance man-hours, maintenance cost for Lean PM in a radar system. The direction of LEAN on supportability in a weapon system is suggested.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.130-139
• /
• 2020

The defense industry is a future-oriented industry, in which high-tech technologies are concentrated. In addition, it is a key industry for maintaining national security, and the R&D of the defense industry is very important. With the introduction of a competitive system by defense industry companies, the necessity of improving the efficiency and productivity of defense industry companies is emerging. In this study, the efficiency of the defense industry was measured using the CCR and BCC model. In addition, super efficiency was derived using the Super-SBM model. For this study, the 2019 defense industry management analysis data of the Korea Defense Industry Association (KDIA) was used, and the analysis was performed by setting the number of researchers and investments of domestic defense industry companies as the input variables and sales as the output variables. Through this study, it is expected that the defense industry's R&D efficiency will be grasped, which will help establish a policy for fostering the defense industry in the future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1972-1980
• /
• 2015

This study's purpose was to analyze the effect of the SmartCare obesity management pilot project, which was conducted between 09 March 2011 and 03 April 2013 in Korea (South). Of 212 subjects who were enrolled in the study, the final analysis was conducted with 147 subjects who completed their weight self-measurements and SmartCare services until the end of a 6-month service period. The self-measurement group for evaluation was classified into 3 groups (Low, Middle, and High) by evenly dividing the monthly average frequency of measurement for 6 months and the evaluation indices were weight, and BMI (Body Mass Index) transmitted from the SmartCare System. The monthly average weight and BMI were decreased more in the High Group than the Middle Group and Low Group (M5: High>Middle>Low), and they are showing statistically significant differences between groups (p< 0.05). In conclusion, analysis of the weight and BMI improvement effect showed a greater improvement effect when the self-measurement frequency level was higher.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.628-633
• /
• 2020

This paper presents an analysis of the shelf-life management program of the long-term storage one-shot system. The one-shot system is mainly maintained with long-term storage or non-operating status and is operated once at execution of the mission. The function corresponding to one-shot is mainly operated through a shelf-life item such as an explosive. The performance and characteristics of shelf-life item are subject to change as the storage period passes. Therefore, shelf-life management for maintaining good condition is very important during long-term storage, and criteria for management is necessary. We present a method for optimizing shelf-life extension by comparing criteria for management with current reliability. Next, the shelf-life evaluation schedule was decided by utilizing the reliability function of exponential distribution and Weibull distribution. Continuously accumulated test data from the shelf-life evaluation were analyzed, and the parameter of distribution was updated. The extension or expiration of shelf-life was selected by monitoring changes in reliability. In addition, we confirmed the applicability of the presented shelf-life management program by applying ASRP test data of the one-shot system K000 fuse.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.1
• /
• pp.287-294
• /
• 2010

The focus of this paper falls on assessing how well rule of crafting government R&D institution spin-off companies(GRSCs), legitimatized to boost up technology commercialization of government research institutions(GRIs) at Daedeok Innopolis in 2006, affect the better business performance of GRSCs, but also delivering alternatives of driving up their better business. First of all, this paper evaluate a management performance of GRSCs at the financial aspect by taking 5 different GRSCs cases among 16 to measure the overall performance of GRSCS's Technology commercialization. Second, this paper assess the effectiveness of GRSCs to bring the better performance of technology commercialization. Third, this paper suggest soft program-centered technology commercialization model, rather institution and ceremonial-oriented one, for GRIs. Overall, the outcomes of this paper will contribute to accommodate the rule of GRSCs attaining goals set in the initial policy domain.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.3
• /
• pp.1294-1298
• /
• 2014

Comparative analysis study of the flow characteristics and the experiment was done to try to present the orientation of the solenoid structure to be produced in the future. The comparative analysis of the analysis and experimental values was performed using the experiments and ANSYS CFD. 3D modeling of the structure are designed by the CATIA V5R18, meshing process of the flow section was used by ICEM CFD program. Flow rate was indicated by using the experimental values appear in $0-10{\ell}/min$, the result of the flow analysis, was $0.18{\ell}/min$ Max. It was possible to suggest a solenoid structure more efficient through comparative analysis of experimental values and flow analysis.