• 한국해양공학회지
• /
• 제6권1호
• /
• pp.105-112
• /
• 1992

The main purpose of this study is to derive a law of fatigue crack growth rate in the region of elastic or elasto-plastic fracture mechanics at elevated temperatures through the application of dimensional analysis. An equation of elasto-plastic fatigue crack growth rate at elevated temperatures appeared a new Arrhenius type equation containing J-integral range and absolute temperature. The elastic or elasto-plastic crack growth rate equation shows a fairly good agreement with the experimental results for Cr-Mo-V rotor steel and Hastelloy-X alloy in the comparatively wide temperature ranges.

• 한국환경과학회지
• /
• 제8권2호
• /
• pp.151-154
• /
• 1999

To verify the accuracy of the numerical experiment of Part I, measurements at the matured rice canopy located around Junam reservoir were performed at August 14, 1995. According to the measured data, the foliage temperature recorded the highest value, and the ground temperature was the lowest around noon, and these results coincided with those of the numerical experiment using the combined model of Part I. From the estimation using measured data, the maximum value of the latent heat flux was 380$Wm^2$, the highest value among energy balance terms, and the energy redistribution ratio of the latent heat flux was averaged as 0.5, the highest values among redistribution ratios. These results are the same as those of the numerical experiment in tendency, but they reveals a little lower in the absolute values than those from the numerical experiment.

• 한국안전학회지
• /
• 제21권4호
• /
• pp.66-72
• /
• 2006

An accurate knowledge of the AITs(autoignition temperatures) is important in developing appropriate prevention and control measures in industrial fire protection. The measurement of AITs are dependent upon many factors, namely initial temperature, pressure, vessel size, fuel/air stoichiometry, catalyst, concentration of vapor, ignition delay time. The values of the AITs used process safety are normally the lowest reported, to provide the greatest margin of sefety. This study measured the AITs of o-xylene+n-pentanol system from ignition delay time by using ASTM E659-78 apparatus. The experimental AITs of o-xylene and n-pentanol were $480^{\circ}C\;and\;285^{\circ}C$, respectively. The experiment AITs of o-xylene+n-pentanol system were a good agreement with the calculated AITs by the proposed equations with a few A.A.D.(average absolute deviation).

• 한국정밀공학회지
• /
• 제15권4호
• /
• pp.44-50
• /
• 1998

The creep life fraction can be evaluated by the degree of grain deformation since the grain of Cr-Mo base metal deforms in the direction of stress. The grain deformation method using image processing technique is developed for life assessment of in-service high-temperature components. The new assessment model of grain deformation method is presented to apply to in-service components and is verified by interrupted creep test for ex-serviced material of 1Cr-0.5Mo steel. The proposed model, which is irrespective of stress direction, is to evaluate mean of the absolute deviation for the measured ratios which are diametrical maximum to minimum dimensions for grains.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1139-1143
• /
• 1991

Using industrial robots and sensors, we developed an inline car body inspection system which proposes high flexibility and sufficient accuracy. Car Body Inspection(CBI) cell consists of two industrial robots, two corresponding carriages, camera vision system, a process computer with multi-tasking ability and several LDS's. As industrial robots guarantee sufficient repeatabilities, the CBI cell adopts the concept of relative measurement instead of that of absolute measurement. By comparing the actual measured data with reference data, the dimensional errors of the corresponding points can be calculated. The length of the robot arms changes according to ambient temperature and it affects the measuring accuracy. To compensate this error, a robot arm calibration process was realized. By measuring a reference jig, the differential changes of the robot arms due to temperature fluctuation can be calculated and compensated.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 제5회 압연심포지엄 신 시장 개척을 위한 압연기술
• /
• pp.349-358
• /
• 2004

The strip temperature history of finishing mill process is one of the most important factors to stabilize the facilities and to achieve the better product quality including a better prediction of roll force etc. The ultimate goal of this study is to improve scientific understanding of the finishing mill process in the view of heat transfer science. Finishing mill cooling facilities of KwangYang $\#3$ hot rolling are introduced and heat transfer analyses from FET to FDT are particularly focused in this study Three major tasks are successfully achieved as follows: 1) The temperature Prediction Models are developed. 2) The average absolute error is found to be less then 10 Celsius degree (about $8.5^{\circ}C$). 3) Prediction rate (less then $\bar{+}20$) are $10.2\%$ improved $(80.1\;\rightarrow\;90.3\%)$.

• 자원리싸이클링
• /
• 제27권2호
• /
• pp.63-67
• /
• 2018

자유에너지는 물질의 상대적인 안정도를 나타낸다. 수용액에 존재하는 이온의 종류는 다양하고 실험조건이 광범위하므로 열역학 자료가 부족하다. 이온의 표준생성엔탈피와 엔트로피로부터 표준수화엔탈피와 표준수화엔트로피의 절대값과 상대값을 구하는 방법을 설명하였다. 또한 대응원리를 이용하여 고온에서 열역학 자료를 추산하는 방법을 설명하였다.

• 한국연초학회지
• /
• 제6권1호
• /
• pp.33-37
• /
• 1984

The net enthalpy changes for the water desorption of sun-cured tobacco have been studied. In order to compare the values of net enthalpy changes for the samples at the same moisture contents, correlation analyses have been performed. The results are summarizing as followings : 1 . As temperature and water vapor pressure increased, equlibrium moisture content were approaching to the saturated vapor pressure of water. 2. The values of 1nP against the reciprocal of absolute temperature were linear for the water desorption of samples. 3. Multiple regression was analyzed to calculate the values of 1nP at the same moisture content. The significance of $x^2$-test for the multiple regression was 0.5%. 4. The values of net enthalpy changes for Basma were greater than those of Sohyang at the same moisture content.

• International Journal of Air-Conditioning and Refrigeration
• /
• 제9권4호
• /
• pp.1-9
• /
• 2001

The temperature and moisture distributions in a dry room with a heat and moisture source -i.e., workers- are studied numerically by using a standard $k-\varepsilon$ turbulence model. In order to evaluate the effectiveness of heat and moisture ventilation inside the room, the heat removal capacity and the moisture exhaust efficiency are introduced. The effectiveness of ventilation control is analyzed by evaluating the temperature and humidity distributions in the room quantitatively. It is found that the mean absolute humidity inside the room is almost constant regardless of the models and the heat generation rates in this study range. This results from the fact that the moisture generation by the workers was relatively small. Through the modification of the design, 40% improvement in critical decay time was achieved.

• 우주기술과 응용
• /
• 제1권3호
• /
• pp.356-363
• /
• 2021

중적외선을 이용하여 획득한 영상은 상온 부근의 온도 측정에는 적당하지 않다는 것이 교과서적 상식이었으나, 최근 중적외선 센서를 이용한 위성 영상을 살펴보면 중적외선 센서를 이용하여 측정한 결과물도 상온 부근의 온도를 측정할 수 있다는 가능성을 보여주고 있다. 본 논문에서는 중적외선 센서를 가지는 위성영상의 상온 온도 정보 추출 가능성 및 정확도에 대해 살펴보고자 한다. 논문에서 검토된 중적외선 위성영상은 상온 부분의 온도를 잘 표시하였으며, 측정된 온도의 절대값으로서의 신뢰성에 관해서는, 태양광의 지표면 직접 반사에 의한 열전달량 영향과 대기에서 흡수되는 적외선 대기 흡수량의 영향은 비교적 작거나 일정한 값으로 볼 수 있지만, 비접촉식 온도계의 한계인 물성치의 의한 복사 계수(emissivity)의 불확실성 문제는 여전히 해결해야할 문제로 남아 있게 되었다.