• 공업화학
• /
• 제29권4호
• /
• pp.405-412
• /
• 2018

알칸디올로부터 유래된 주사슬의 탄소수가 6, 9, 11인 bis[3-(dialkyloxylphosphorothionyl)thio-2-methylpropanyloxy]alkane (BAPA)를 합성하였으며, 이를 zinc dialkyl dithiophosphates (ZDDP)와 비교하여 마모억제성능을 살펴보았다. 탄소 주사슬의 길이에 따른 BAPA의 내마모성능을 확인하기 위하여 4-ball 시험을 하였다. 기유무게의 1% 농도로 첨가제를 넣고 WSD (wear scar diameter)를 측정하였고, 각 0.472, 0.459, 0.480 mm로 나타났다. 또한 BAPA 화합물 중 bis[methacryloyloxy]nonane (BMOO9)의 곁사슬인 dialkyl dithiophosphoric acid (DDP)의 탄소수를 4, 8, 12로 변화시켜 합성하여, 4-ball 시험을 하였다. 그 결과로 WSD의 값은 각각 0.537, 0.459, 0.531 mm로 측정되었다. 곁사슬이 짧으면 필름이 얇게 형성되고, 길면 필름형성을 방해하여 탄소수가 8개일 때의 값이 제일 좋게 나타났다. ZDDP의 경우 동일한 조건에서 WSD의 값이 0.563 mm로 측정되었고, 합성한 BAPA의 화합물이 마모억제용 첨가제로 더 우수한 성능을 갖는다는 것을 확인하였다.

• 한국결정성장학회지
• /
• 제16권3호
• /
• pp.121-126
• /
• 2006

HVOF thermal spray coating of Co-alloy T800 is progressively replacing the classical hard coatings such as chrome plating because of the very toxic $Cr^{6+}$ ion known as carcinogen causing lung cancer. For the study of the possibility of replacing of chrome plating, the wear properties of HVOF Co-alloy T800 coatings are investigated using the reciprocating sliding tester both at room and at an elevated temperature of $1000^{\circ}F\;(538^{\circ}C)$. The possibility as durability improvement coating is studied for the application to the high speed spindles vulnerable to frictional heat and wear. Wear mechanisms at the reciprocating sliding wear test are studied for the application to the systems similar to the sliding test such as high speed spindles. Wear debris and frictional coefficients of T800 coatings both at room and at an elevated temperature of $1000^{\circ}F\;(538^{\circ}C)$ are drastically reduced compared to those of non-coated surface of parent substrate Inconel 718. This study shows that the coating is recommendable for the durability improvement coatings on the surfaces vulnerable to frictional heat. The sliding surfaces are weared by the mixed mechanisms such as oxidative wear, abrasion by the sliding ball slurry erosion by the mixture of solid particles and small drops of the melts and semi-melts of the attrited particles cavitation by the relative motions among the coating, sliding ball, the melts and semi-melts. and corrosive wear. The oxide particles and the melts and semi-melts play roles as solid and liquid lubricant reducing the wear and friction coefficient.

• Tribology and Lubricants
• /
• 제34권6호
• /
• pp.209-216
• /
• 2018

Sapphire is a substrate material that is widely used in optical and electronic devices. However, the processing of sapphire into a substrate takes a long time owing to its high hardness and chemical inertness. In order to process the sapphire ingot into a substrate, ingot growth, multiwire sawing, lapping, and polishing are required. The lap grinding process using pellets is known as one of the ways to improve the efficiency of sapphire substrate processing. The lap grinding process ensures high processing efficiency while utilizing two-body abrasion, unlike the lapping process which utilizes three-body abrasion by particles. However, the lap grinding process has a high material removal rate (MRR), while its weakness is in obtaining the required surface roughness for the final polishing process. In this study, we examine the effects of free abrasives in lap grinding on the material removal characteristics of sapphire substrate. Before conducting the lap grinding experiments, it was confirmed that the addition of free abrasives changed the friction force through the pin-on-disk wear test. The MRR and roughness reduction rate are experimentally studied to verify the effects of free abrasive concentration on deionized water. The addition of free abrasives (colloidal silica) in the lap grinding process can improve surface roughness by three-body abrasion along with two-body abrasion by diamond grits.

• 대한기계학회논문집A
• /
• 제24권9호
• /
• pp.2387-2396
• /
• 2000

Wear and operation characteristics of Nylon and Acetal pinion against steel gear were studied to gain a better understanding of their tribological and mechanical behavior. Tests were conducted with power circulating gear test rig under unlubricated conditions. Specific wear rates were measured as a function of applied load and total revolution. The worn tooth surfaces were examined with a profile projector and camera. Nylon pinion showed lower specific wear rates than Acetal pinion, but it revealed breakage at high load. Principal wear depths were developed at tooth tip and below the pitch line of pinion. Life estimation for the Nylon pinion was made by taking into account steel gear equivalent Hertz stress and average sliding velocity. The dominant wear mechanisms were adhesion and abrasion.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.585-588
• /
• 2004

In this study, Curve dependent wheel flange lubricator with grease spray type is investigated and estimated a point of view reducing wheel flange wear and noise in the curve through field test on korean rail. Advantage of curve dependent wheel flange lubricator with grease spray type is found on the basis of the result of field test in comparison with oil spray type lubricator and wheel without wheel flange lubricator on railroad in Korea.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.633-637
• /
• 2003

In this study, Curve dependent wheel flange lubricator with grease spray type is investigated and estimated a point of view reducing wheel flange wear and noise in the curve through field test. Advantage of curve dependent wheel flange lubricators with grease spray type is found on the basis of the result of field test in comparison with flange lubricator of oil spray type and bogie without wheel flange lubricator on railroad in korea.

• 한국주조공학회지
• /
• 제38권1호
• /
• pp.16-26
• /
• 2018

In this study, the effects of the pouring temperature, preheating temperature, surface condition and fraction of the wear resistant part on the production of duo-castings were investigated using a high Cr white cast iron with excellent abrasion resistance and a low Cr alloy steel with good toughness. The constituent materials of the duo-castings were designed to have high hardness, fracture toughness and abrasive wear resistance for the replacement of high Mn alloy steels with low abrasive wear resistance. In particular, the amount of abrasive wear of 17% Cr white cast iron was about 1/20 of that of high Mn alloy steel. There was an intermediate area of about 3mm due to local melting at the bonding interface of the duo-castings. These intermediate regions were different from those of the constituent materials in chemical composition and microstructure. This region led to fracture within the wear resistant part rather than at the bonding interface in the bending strength test. The bending fracture strengths were 516-824 MPa, which were equivalent to the bending proof strength of high Mn steel. The effects of various casting conditions on the duo-cast behavior were studied by simple pouring of low Cr alloy steel melt, but the results proved practically impossible to manufacture duo-castings with a sound bonding interface. However, the external heating method was suitable for the production of duo-castings with a sound bonding interface.

• Tribology and Lubricants
• /
• 제27권6호
• /
• pp.321-325
• /
• 2011

Nanodiamond was dispersed in paraffin liquid oil to investigate the effects of nanodiamond at the marginally lubricated condition. Scuffing test and immediate loading sliding wear test were conducted using the fabricated nanodiamond oil. As a result, dispersion of nanodiamond in oil leads to increase in scuffing life, and nanodiamond contents affects the scuffing life. In case of immediate loading sliding wear test, the result was different according to hardness of specimen. If hardness of specimen was low, abrasion of nanodiamond occurred actively. If hardness of specimen was increased, however, nanodiamond can act as a spacer or rolling between contacting surfaces.

• 구강회복응용과학지
• /
• 제21권1호
• /
• pp.69-81
• /
• 2005

The objective of this study was to evaluate the toothbrush abrasion characteristics of class V restorations. Thirty extracted human premolars, which were collected from oral surgery clinics were used. We mounted five teeth in a metal ring mold of 50 mm in diameter and 15 mm in height using chemically cured acrylic resin. Class V cavities were prepared in lingual cervical root surfaces and restored using one of following restorative materials : Dentin Conditioner/Fuji II LC (Group FL), All Bond II/Z-250 (Group ZT), One-up Bond F/Palfigue Estelite (Group PE), F2000 Primer/Adhesive (Group FT), and Prime & Bond 2.1/Dyract AP (Group DR). They were stored under distilled water at $37^{\circ}C$ for seven days. The toothbrush abrasion test was conducted using a wear testing machine of pin-on disk type under a load of 1.5 N for 100,000 cycles. We have examined the bonded interfaces, the changes of surface roughness and color of abraded surfaces. From this experiment, the following results were obtained. 1. The change of surface roughness showed high degree: RMGIC>compomer>composite resin (p<0.05). 2. Because of the protrusion and missing of filler particles, SEM observation of abraded surfaces of RMGIC and compomers revealed the increase of surface roughness due to the selective removal of matrix resin. 3. The color change by toothbrush abrasion was affected in large part by the change of $L^*$ and $b^*$ of resin composites (p<0.05). 4. The color change by toothbrush abrasion was so small to detect by human eyes. 5. SEM observation of abraded surfaces revealed the interface bonding was the best in the FT group.

• 대한의용생체공학회:의공학회지
• /
• 제22권6호
• /
• pp.519-526
• /
• 2001

At present. about 0.3 million and more THRs (Total Hip Replacement) in a rear are being done worldwide. The increase in mechanical failure with the increase in THR, required more revisions. Revisions compensate mainly the wear of the artificial joint frictional surface and the loosening of the cup and stem. According to recent researches, loosening is mainly due to wear debris UHMWPE (Ultra High Molecular Weight Polyethylene) from frictional surfaces . To overcome the wear problems associated with artificial joint materials , new surface structures with regular Patterns were designed and fabricated The lubrication Properties were examined to evaluate the wear of the frictional surfaces. The surface structure manifested a Pattern of "dents" with a 0.2-1.0 mm of diameter and 0.6-2.0 mm of Pitch. From the friction test of the SUS316L vs UHMWPE using the frictional tester, we found that the lubrication Performance was improved due to of drastically reduced amount of abrasion. There were optimum sizes for the diameter and the pitch of the Pattern. The results demonstrated that the lubrication properties could be improved by Patterning of the frictional surfaces. The surface Patterning was effective in preventing wear of the frictional surfaces, and the life of an artificial joint could be extended with such Patterning.