• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.405-409
• /
• 2009

In this paper, the effects of LLR (Log-Likelihood Ratio) approximation on LDPC (Low-Density Parity-Check) decoder performance are analyzed, and optimal design conditions of LDPC decoder are derived. The min-sum LDPC decoding algorithm which is based on an approximation of LLR sum-product algorithm is modeled and simulated by MATLAB, and it is analyzed that the effects of LLR approximation bit-width and maximum iteration cycles on the bit error rate (BER) performance of LDCP decoder. The parity check matrix for IEEE 802.11n standard which has block length of 1,944 bits and code rate of 1/2 is used, and AWGN channel with QPSK modulation is assumed. The simulation results show that optimal BER performance is achieved for 7 iteration cycles and LLR bit-width of (7,5).

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.6
• /
• pp.301-305
• /
• 2007

In this paper, we propose a simple algorithm for detecting underwater transient signals on the fact that the frequency range of underwater transient signals is similar to audio frequency. For this, we use a preprocessing module of EVRC speech codec that is the standard speech codec of the mobile communications. If a signal is entered into EVRC noise suppression module, we can get some parameters such as the update flag, the energy of each channel, the noise suppressed signal, the energy of input signal, the energy of background noise, and the energy of enhanced signal. Therefore the energy of the enhanced signal that is normalized with the energy of the background noise is compared with the pre-defined detection threshold, and then we can detect the transient signal. And the detection threshold is updated using the previous value in the noisy period. The experimental result shows that the proposed algorithm has $0{\sim}4% error rate in the AWGN or the colored noise environment.

• Journal of IKEEE
• /
• v.2 no.2 s.3
• /
• pp.212-224
• /
• 1998

There are two major factors of degrading the performance in the forward link of DS/CDMA systems. One is the multiple access interference (MAI) caused by using the same frequency bands simultaneously and the other is the multipath lading due to multipath propagation. PN codes which have minimum cross correlation properties among spread spectrum codes are necessary to reduce the MAI. In the conventional IS-95A system, the PN sequence has the period of $2^{15}$ and is of the length of 64 chips for spreading each data. In this case, since the length of PN code per bit is very short compared to the period of the PN code, the performance of the conventional system is not satisfied in view of suppressing the multipath interference. However, the correlation property of the PN codes at the demodulation can be improved by increasing the interval of Integration at the demodulation. This paper proposes a demodulation method to reduce the cross correlation among PN codes. The performance of the proposed demodulation method is investigated through computer simulations. We used multipath Ray lading channel and AWGN channel in the simulation. Our simulation results show the improved performance of $0.25{\sim}0.5dB$ SNR in a given BER compared to the conventional demodulation scheme.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.868-882
• /
• 2009

In this paper, channel model and wireless link performance analysis for the short-range wireless communication system applications in the terahertz frequency which is currently interested in many countries will be described. In order to realize high data rates above 10 Gbps, the more wide bandwidths will be required than the currently available bandwidths of millimeter-wave frequencies, therefore, the carrier frequencies will be pushed to THz range to obtain larger bandwidths. From the THz atmospheric propagation characteristics based on ITU-R P.676-7, the available bandwidths were calculated to be 68, 48 and 45 GHz at the center frequencies of 220, 300 and 350 GHz, respectively. With these larger bandwidths, it was shown from the simulation that higher data rate above 10 Gbps can be achieved using lower order modulation schemes which have spectral efficiency of below 1. The indoor propagation delay spread characteristics were analyzed using a simplified PDP model with respect to building materials. The RMS delay spread was calculated to be 9.23 ns in a room size of $6\;m(L){\times}5\;m(W){\times}2.5\;m(H)$ for the concrete plaster with TE polarization, which is a similar result of below 10 ns from the Ray-Tracing simulation in the reference paper. The indoor wireless link performance analysis results showed that receiver sensitivity was $-56{\sim}-46\;dBm$ over bandwidth of $5{\sim}50\;GHz$ and antenna gain was calculated to be $26.6{\sim}31.6\;dBi$ at link distance of 10m under the BPSK modulation scheme. The maximum achievable data rates were estimated to be 30, 16 and 12 Gbps at the carrier frequencies of 220, 300 and 350 GHz, respectively, under the A WGN and LOS conditions, where it was assumed that the output power of the transmitter is -15 dBm and link distance of 1 m with BER of $10^{-12}$. If the output power of transmitter is increased, the more higher data rate can be achieved than the above results.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.4
• /
• pp.195-205
• /
• 2014

The ultra-high definition television (UHDTV) has been considered as a next generation broadcsating service. However the conventional digital terrestrial transmission system cannot afford the required transmission data rate of UHDTV, and thus adopting ultra-high order constellation, such as 4096-QAM, into the conventional DTT systems has been studied. In particular, when the ultra-high order constellation is adopted into the digital video broadcasting-2nd generation terrestrial (DVB-T2) unequal-error protection (UEP) properties of a codeword of an error correction coding and ultra-high order constellations should be properly matched by bit mapper in order to enhance the decoding performance. Because long codeword results in a heavy computational complexity to design the bit mapper, the DVB-T2 divided it into cascaded blocks, the bit interleaver and the bit-to-cell DEMUX, and there have been many researches related to each block. However, there are few published study related to design methodology of bit interleaver. In this respect, this paper proposes a design methodology of the bit interleaver and presents bit interleavers of 1024-QAM and 4096-QAM according to the proposed design algorithm. The newly designed interleavers improved the decoding performance of the error correction coding by maximally 0.6 dB SNR over both of AWGN and random fading channel.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.46 no.4
• /
• pp.148-156
• /
• 2009

This paper presents a new image rejection algorithm based on the analysis of the distortion of a single-frequency continuous-wave (CW) signal due to the I/Q mismatch. Existing methods estimated the gain mismatch and phase mismatch on RF receivers and compensated them However, this paper shows that the circular trajectory of a single-frequency CW signal is distorted elliptic-type trajectory due to the I/Q mismatch. Utilizing the analysis, we propose a I/Q mismatch compensation method. It has two processing steps. In the first processing step, the generated signal is rotated to align the major axis of the elliptic-type trajectory diagram with the x-axis. In the second processing step, the Q-channel signal in the regenerated signal is scaled to align the regenerated signal with the transmitted single-frequency CW signal. Simulation results show that a receiver using the proposed image rejection algorithm can achieve an image rejection ratio of more than 70dB. And, simulation results show that the bit error rate performances of receivers using the proposed image rejection algorithm are almost the same as those of conventional coherent demodulators, even in fading channels.

• Journal of Broadcast Engineering
• /
• v.25 no.6
• /
• pp.870-881
• /
• 2020

This paper presents cell ID (cell identity) detection schemes using PSS/SSS (primary synchronization signal/secondary synchronization signal) for 5G NR (new radio) system and evaluates the detection performance. In this paper, we consider two cell ID detection schemes, i.e. two-stage detection and joint detection schemes. The two-stage detection scheme consists of two stages which estimate a channel gain between a transmitter and receiver and detect the PSS and SSS sequences. The joint detection scheme jointly detects the PSS and SSS sequences. In addition, this paper presents coherent and non-coherent combining schemes. The coherent scheme calculates the correlation value for the total length of the given PSS and SSS sequences, and the non-coherent combining scheme calculates the correlation within each group by dividing the total length of the sequence into several groups and then combines them non-coherently. For the detection schemes considered in this paper, the detection error rates of PSS, SSS and overall cell ID are evaluated and compared through computer simulations. The simulation results show that the joint detection scheme outperforms the two-stage detection scheme for both coherent and non-coherent combining schemes, but the two-stage detection scheme can greatly reduce the computational complexity compared to the joint detection scheme. In addition, the non-coherent combining detection scheme shows better performance under the additive white Gaussian noise (AWGN), fixed, and mobile environments.