• Proceedings of the KIPE Conference
• /
• 2010.07a
• /
• pp.552-553
• /
• 2010

Dual Buck Inverter 구조를 갖는 35W 세라믹 MHL용 전자식 안정기의 제어회로를 설계하였다. 제어회로는 크게 2가지로 나눌 수 있는데 PFC IC를 이용하여 Inverter의 전압과 전류를 센싱하여 80kHz로 Inverter를 구동하기 위한 제어부분과 시간의 경과에 따른 PFC의 출력 전압 제어, Ignition Pulse 제어 및 무부하 보호, 램프의 점등 상태에 따른 Inverter 구동 주파수 제어부분으로 구성되어 있다. 본 논문은 마이크로 컨트롤러(ATmega8)를 이용하여 시간의 경과에 따른 안정기의 제어부분에 대해 설명하고 이를 실험을 통해 검증하였다.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.1016-1023
• /
• 2013

Predictive current control offers the potential for achieving more precise current control with a minimum of distortion and harmonic noise. However, the predictive method is difficult to implement and has a greater computational burden. This paper introduces a theoretical analysis and experimental verification for an improved predictive current control technique applied to single phase grid connected voltage source inverters (VSI). The proposed technique has simple calculations. An ATmega1280 microcontroller board is used to implement the proposed technique for a simpler and cheaper control system. To enhance the current performance and to obtain a minimum of current THD, an improved tri-level PWM switching strategy is proposed. The proposed switching strategy uses six operation modes instead of four as in the traditional strategy. Simulation results are presented to demonstrate the system performance with the improved switching strategy and its effect on current performance. The presented experimental results verify that the proposed technique can be implemented using fixed point 8-bit microcontroller to obtain excellent results.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2009.11a
• /
• pp.51-52
• /
• 2009

본 논문에서는 차량 내의 네트워크 가운데에서 대용량의 멀티미디어 데이터를 전송할 수 있는 MOST(Media Oriented Systems Transport) 네트워크 기반의 오디오 인포테인먼트 인터페이스 개발에 관한 연구를 수행하였다. 구현한 오디오 인포테인먼트 인터페이스는 MOST 네트워크 인터페이스 컨트롤러로 OS81050A INIC 칩을 사용하였으며, EHC 부분은 ATmega128L 8bit 마이크로컨트롤러를 사용하였다. 오디오 동작과 관련된 기능 블록(FBlock) 및 애플리케이션 작성에는 NetServices API를 활용하였다. 구현된 인터페이스는 MOST 네트워크 분석 도구인 OptoLyzer G2를 이용하여 정확한 동작여부를 확인하였다.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.172-174
• /
• 2020

기존의 절대위치 감지 방식은 초기위치를 알기 위하여 이동자의 위치를 초기화해야 하고 생산 단가가 높다는 단점을 보완하기 위해 MR 센서를 이용하여 비접촉 방식으로 선형모터 이동자 절대위치를 판별하는 시스템을 제안하였다. 센서값을 이용하여 절대위치를 판별해야 하기 때문에 ADC 기능과 실시간 연산 기능이 필요하다. 때문에 8bit MCU(Atmega324PA)를 이용했다. 본 논문에서 이용한 MR 센서의 출력 변동폭이 작기 때문에 Instrumentation Amplifier를 이용하여 증폭된 출력을 MCU로 읽어 사용했다. 제안 시스템의 회로 및 알고리즘을 구현하였고 이를 이론적, 실험적 분석을 통해 동작 및 타당성을 검증하였다.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.5
• /
• pp.436-442
• /
• 2020

ESS(energy storage system) has recently become an important power source in various areas due to increased renewable energy resources. The more ESS is used, the less the effective capacity of the ESS. Therefore, it is important to manage the remaining useful lifetime(RUL). RUL can be checked regularly by inspectors, but it is common to be monitored and estimated by an automated monitoring system. The accurate state estimation is important to ESS operator for economical and efficient operation. RUL estimation model usually requires complex mathematical calculations consisting of cycle aging and calendar aging that are caused by the operation frequency and over time, respectively. A lightweight RUL estimation model is required to be embedded in low-performance processors that are installed on ESS. In this paper, a lightweight ESS RUL estimation model is proposed to operate on low-performance micro-processors. The simulation results show less than 1% errors compared to the original RUL model case. In addition, a performance analysis is conducted based on ATmega 328. The results show 76.8 to 78.3 % of computational time reduction.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1826-1829
• /
• 2005

Recent advancement in wireless communications and electronics has enabled the development of low power sensor network. Wireless sensor network are often used in remote monitoring control applications, health care, security and environmental monitoring. Wireless sensor networks are an emerging technology consisting of small, low-power, and low-cost devices that integrate limited computation, sensing, and radio communication capabilities. Sensor network platform for health care has been designed, fabricated and tested. This system consists of an embedded micro-controller, Radio Frequency (RF) transceiver, power management, I/O expansion, and serial communication (RS-232). The hardware platform uses Atmel ATmega128L 8-bit ultra low power RISC processor with 128KB flash memory as the program memory and 4KB SRAM as the data memory. The radio transceiver (Chipcon CC1000) operates in the ISM band at 433MHz or 916MHz with a maximum data rate of 76.8kbps. Also, the indoor radio range is approximately 20-30m. When many sensors have to communicate with the controller, standard communication interfaces such as Serial Peripheral Interface (SPI) or Integrated Circuit ($I^{2}C$) allow sharing a single communication bus. With its low power, the smallest and low cost design, the wireless sensor network system and wireless sensing electronics to collect health-related information of human vitality and main physiological parameters (ECG, Temperature, Perspiration, Blood Pressure and some more vitality parameters, etc.)

• Journal of Navigation and Port Research
• /
• v.47 no.2
• /
• pp.85-92
• /
• 2023

The hardware of an LED lighting control system for coastal lighting at coastal pier entrance consists of a power supply unit, an AVR control unit, a CLCD output unit, an LED control unit, a scenario selection switch unit, and an operation speed display unit. It is made of an 8-channel. The CPU used ATmega128 and the FET was used to control the current signal. To operate the CPU, DC 12V was converted to DC 5V using a regulator 7805. A heat sink was used to remove heat generated in the FET. By connecting the load LED module to the manufactured 8-channel LED lighting control system, the operation was confirmed through various production scenarios. In addition, a control system was designed to show the most suitable color for the atmosphere of the coastal pier according to the input value of temperature and illumination using a fuzzy control system. Computer simulation was then conducted. Results confirmed that fuzzy control did not need to store many data inputs due to characteristics of artificial intelligence and that it could efficiently represent many output values with simple fuzzy rules.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.21 no.5
• /
• pp.35-45
• /
• 2011

The Salsa20/12 stream cipher selected for the final eSTREAM portfolio has a better performance than software implementation of AES using an 8-bit microprocessor with restricted memory space, In the theoretical approach, the evaluation of exploitable timing vulnerability was 'none' and the complexity of side-channel analysis was 'low', but there is no literature of the practical result of power analysis attack. Thus we propose the correlation power analysis attack method and prove the feasibility of our proposed method by practical experiments, We used an 8-bit RISC AVR microprocessor (ATmegal128L chip) to implement Salsa20/12 stream cipher without any countermeasures, and performed the experiments of power analysis based on Hamming weight model.

• Journal of the Institute of Convergence Signal Processing
• /
• v.8 no.1
• /
• pp.58-62
• /
• 2007

Digital communication is important for reliability and mobilization of the multi-channel communication systems. Transmitting and receiving data for the mobilization should be possible in anywhere and in anytime. And this system must be designed light weight small size and low power. One are essential technology for implementing the mobile wireless communication system on the age of ubiquotos. Requirements in constructing such communication field are followings. At first data transmitting and receiving should be carried out by a simple command. Second, the device should be designed as hand-hold type and low power consumption. Third, data communication should be reliable. As one of examples, car to car system which is popular in the market is introduced here, All traffic information in highway is transmitted from one car to another by using this system which can prevent possible traffic accident. This paper shows the design of a digital data communication system with CC1020 chip. This CC1020 makes easy frequency selection and easy switch from the transmit mode to the receive mode by simple setting of a memory register in the chip. The transmit power of this system is designed 10dBm and its communication range is about 100m. The power supplied this system is 3V considered as low power. The sleep mode can be easily entered during transmit mode or receive mode. We shows the program algorithm of CC1020 and interface circuit between MCU and CC1020. We shows the Photo of the CC1020 Module and Atmega128 Module.. We analysed the receiver rate with this system.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.193-193
• /
• 2009

Thin-type 초음파모터의 구조는 크로스형태의 앓은 스테이터에 윗면과 아랫면에 각각 8개의 압전세라믹이 부착된 형태이고, 압전세라믹의 분극방향은 로터와 접촉하는 스테이터의 중심부인 네 개의 타점에서 순차적인 타원변위가 생성되도록 결정된다. 유한요소해석프로그램인 ATILA 5.2.4를 사용하여 형태, 길이, 두께, 스테이터 재질, 클램프특성이 최적 설계된 모델을 제작하였고, 푸쉬풀 게이지, x-y 스테이지, rpm 메터, 토크 게이지, 맨코더, AD컨버터를 이용하여 피드백 제어 구동시스템을 구성하였다. 그림 I은 마이크로컨트롤러 (ATmega)와 피드백회로를 이용한 구동 드라이버를 보여준다. 한 주기에서 1/4분주의 순차적인 네 개의 구형파를 생성하고, 이를 push-pull회로를 통하여 90도의 위상차가 나는 정현파를 생성하여 초음파 모터의 구동전원으로 사용한다. 피드백 회로인 엔코더와 AD 컨버터는 초음파모터의 속도를 피드백하여 정속도 운전을 위한 전압제어에 사용되었다. 특성 측정 결과, 제품화된 드라이버와 비교하여 큰 차이를 보이지 않았고 피드백 회로를 통하여 부하변화에 따른 속도의 극심한 변화를 0.2~0.4[N]의 범위에서 정속도 운전이 가능하였으며, 장시간의 운전에도 온도 및 속도특성이 안정적임을 확인하였다.