• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.282-285
• /
• 1999

The (1-x)MgTiO$_3$-xSrTiO$_3$(x=0,0.1) ceramics were prepared by the conventional mixed oxide method. The structural properties were investigated with sintering temperature and composition ratio by XRD, SEM and DT-TGA. Increasing the sintering temperature from 130$0^{\circ}C$ to 1$600^{\circ}C$, second phase was decreased and grain size was increased. In the case of 0.9 MgTiO$_3$-0.1SrTiO$_3$ ceramics sintered at 130$0^{\circ}C$, dielectric constant, quality factor and temperature coefficient of resonant frequency were 22.61, 10,928(at 1GHz), +50.26ppm/$^{\circ}C$ , respectively.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.1
• /
• pp.16-16
• /
• 1991

Generally brittle eta phase produced during TiC deposition has a effect on the TRS (transverse rupture strength ; thoughness). Therefore it is necessary to reduce eta(η), phase for the improvement of tool life. At this experiment some properties (TRS, bonding strength, tool life, eta phase)have been investigated by inserting TiN or TiCN underlayer between TiC layer and substrate. The results obtained were as follows; 1. by inserting underlayer eta phase were decreased and TRS was increased, but the bonding strength was decreased. 2. the diffusion of W, Co from the substrate was hindered by the underlayer. 3. TiC layer with TiCN underlayer had the finsest grain size. 4. by inserting underlayer (TiCN or TiN) the tool life was improved and especially notch and crater wear resistance was greatly improved.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.1
• /
• pp.16-23
• /
• 1992

Generally brittle eta phase produced during TiC deposition has a bad effect on the TRS (transverse rupture strength ; thoughness). Therefore it is necessary to reduce eta(η) phase for the improvement of tool life. At this experiment some properties (TRS, bonding strength, tool life, eta phase) have been investigated by inserting TiN or TiCN underlayer between TiC layer and substrate. The results obtained were as fellows; 1. by inserting underlayer eta phase was decreased and TRS was increased, but the bonding strength was decreased. 2. the diffusion of W, Co from the substrate was hindered by the underlayer. 3. TiC layer with TiCN underlayer had the finsest gain size. 4. by inserting underlayer (TiCN or TiN) the tool life was improved and especially notch and crater wear resistance was greatly improved.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.10a
• /
• pp.87-89
• /
• 1997

The BaTiO$_3$ fine powder was prepared by hydrthermal method using titanium tetrahydoxide (Ti(OH)$_4$) and barium dihydroxide (Ba(OH)$_2$.8$H_2O$) as raw materials. The fine powder was obtained at temperatures as low as 160 to 185$^{\circ}C$. The properties of the BaTiO$_3$ powder were studied as a function of various parameters (reaction temperature, reaction time, Ba/Ti=ratio, etc). The average particle size of the BaTiO$_3$ increased with increasing reaction temperature. After hydrothermal treatment at 17$0^{\circ}C$ for 8 h, the average particle size of the BaTiO$_3$ powder was about 30 nm and the particle size distribution was narrow.

• Journal of the Korean Ceramic Society
• /
• v.33 no.4
• /
• pp.399-404
• /
• 1996

Hydrothemal synthesis of PbTiO3 has been investigated. A comprehensive thermodynamic model for heteroge-nous reacting solid-aquous system has been used to predict the optimum condition for the synthesis. Synthesis were performed using lead acetate trihydrate as Pb source crystalline TiO2 as Ti source and KOH as minerali-zer. The synthesis has been examined at low temperature (16$0^{\circ}C$) Phase pure perovskite PbTiO3 has been obtained at high pH(above 0.5 mol KOH). The morphology of PbTiO3 was acicular shape. It has been found sible for a distortion in the c direction. The water is gradully released on annealing the powder to 40$0^{\circ}C$ and the normal crystallographic properties are restored.

• Journal of Powder Materials
• /
• v.19 no.5
• /
• pp.356-361
• /
• 2012

The ultra-fine and less agglomerated titanium carbonitride particles were successfully synthesized by magnesiothermic reduction with low feeding rate of $TiCl_4+1/4C_2Cl_4$ solution. The sub-stoichiometric titanium carbide ($TiC_{0.5{\sim}0.6}$) particles were produced by reduction of chlorine component by liquid magnesium at $800^{\circ}C$ of gaseous $TiCl_4+1/4C_2Cl_4$ and the heat treatments in vacuum were performed for 5 hours to remove the residual magnesium and magnesium chloride mixed with produced $TiC_{{\sim}0.5}$. The final $TiC_{{\sim}0.5}N_{0{\sim}0.5}$ particle with near 100 nm in mean size and high specific surface area of $65m^2/g$ was obtained by nitrification under nitrogen gas at $1,150^{\circ}C$ for 2 hrs.

• 연구논문집
• /
• s.29
• /
• pp.163-171
• /
• 1999

A new titanium alloy system. Ti-xFe-ySi (x,y=0-4 wt%). was designed and characterized with the point at low cost and high strength for casting applications. Fe improved room and elevated temperature mechanical properties owing to solid solution hardening and beta phase stabilization. Si yielded titanium silicides and Si addition over 1 wt% resulted in poor ductility due to coarse silicide chains at prior beta boundaries. The optimum composition was found to be Ti-4Fe-(0.5-1)Si in the viewpoint of tensile strength and ductility which are comparable to the Ti-6Al-4V. The metal-mould reaction was also examined for Ti-xFe and Ti-xSi binary alloy system. The thickness of surface reaction layer w as not affected significantly with Fe content, while it was decreased with Si content. In the Ti-4Si alloy, no reaction layer was found. The depth of surface hardening layer was about $200\mum$ regardless of the mould materials.

• Journal of Hydrogen and New Energy
• /
• v.14 no.4
• /
• pp.291-297
• /
• 2003

As an alternative bipolar plate material for polymer electrolyte membrane fuel cell (PEMFC), TiN-coated 316 stainless was evaluated in terms of electrical contact resistance and water contact angle. Performance and lifetime of the TiN-coated 316 bipolar plates were measured in comparison with those of graphite and bare 316 bipolar plates. At a cell voltage of 0.6 V, current density of the single cells using graphite, AISI 316, and TiN/316 bipolar plates was 996, 796, and $896mA/cm^2$, respectively. By coating 316 stainless steel with TiN layer, performance degradation rate determined to be the voltage degradation rate at a cell voltage of 0.6 V was reduced from 2.3 to 0.43 mV/h.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.5 s.176
• /
• pp.1124-1132
• /
• 2000

Viscoplastic response and densification behaviors of Ti-6AI-4V powder compacts under uniaxial compression are studied at room and high temperatures with various initial relative densities and strain rates. The yield function and strain-hardening law proposed by Kim and co-workers were implemented into a finite element program (ABAQUS) to compare experimental data with finite element calculations for porous Ti6A14V powder compacts. Displacement-relative density, displacement-load relations and deformed geometry of Ti-A14V powder compacts were compared with finite element results. Density distributions in Ti-6AI-4V powder compacts were also measured and compared with finite element results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.05a
• /
• pp.277-279
• /
• 1996

A.C. and D.C. characteristic of TiO$_2$ added SnO$_2$ are investigated to study the electrical properties. The electrical inductivity increases as TiO$_2$content increase. The doer effect of TiO$_2$ is crucial role for the increase of electrical conductivity. The frequency-dependent ac inductivity increases with the increase of TiO$_2$ contents at low frequency region. However, at high frequency region, the difference of ac conductivity is very small. Impedance spectrums are consist of the one semicircle. Therefore, the sizes of semicircle decreases with increasing the TiO$_2$ contents.