• Structural Engineering and Mechanics
• /
• v.49 no.6
• /
• pp.673-685
• /
• 2014

The topic of this study is to strengthen cracked beams with prefabricated RC U cross-sectional plates. The damaged beams were repaired by epoxy based glue. The repaired beams were strengthened using prefabricated plates. The strengthening plates were bonded to the bottom and side faces of the beams by anchorage rods and epoxy. The strengthened beams were incrementally loaded up to maximum load capacities. The experimental results were satisfactory since the load carrying capacities of damaged beams were increased approximately 76% due to strengthening. It was observed that strengthening plates had a dominant effect on the performance of beams in terms of both the post-elastic strength enhancement and the ductility. The experimental program was supported by a three-dimensional nonlinear finite element analysis. The experimental results were compared with the results obtained from the beam modeled with ANSYS finite element program.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.699-703
• /
• 2017

Numerical simulations of closed-type and open-type single injectors were conducted to investigate the flow characteristics of a swirl-coaxial injector used in a liquid rocket engine. Numerical analysis was conducted using a commercial program ANSYS FLUENT. The injectors has three models with different recess length. Numerical analysis was conducted to investigate the variation of the flow characteristics of the injector when the flow condition were changed. It was also compare and analyzed with experimental results. The results obtained from the numerical simulation show that the difference between the inlet pressure and the discharge coefficient is not significant.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.3
• /
• pp.198-204
• /
• 2022

In this paper, the 5kW and 50kW vertical axis wind turbines were studied using the ANSYS flow analysis simulation program. The 5 kW vertical shaft wind turbine has 30 units of the number of main blades and sub-blades and the electrical characteristics were analyzed by changing the tip speed ratio (TSR) from 0.2 to 06. A 50kW vertical axis wind turbine was designed based on the electrical characteristics of a 5kW vertical axis wind turbine. When the tip speed ratio was 0.5, the 5 kW wind power generation showed the maximum output of 9.5 kW and the efficiency of 0.28. The calculation of the power current(Ip) and the power voltage(Ep) show that, as the tip speed ratio increases, the power current(Ip) decreases and the power voltage(Ep) increases. And even if the tip speed ratio was changed, 5kW wind power generation was measured for output of 5 kW or higher. When the tip speed ratio was changed from 0.3 to 0.6, 50 kW wind power generation was output more than 50 kW. When the tip speed ratio of 50kW wind power generation was 0.4, the output was 58.37 [kW] and the efficiency was 0.318, and it was confirmed that the proposed 50kW wind power generation satisfies the design conditions.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.4
• /
• pp.431-437
• /
• 2003

In this paper, an approximate optimization program based on GUI(graphic user interface) environment is developed. This program is coded by using Fortran and Visual basic. Fortran is used to Progress approximate optimization process. Visual basic is used to make user environment for user to use conveniently. Inside of this program, it uses two independent programs. One is commercial program, ANSYS, and the other is optimization program, PLBA(Pshenichny-Lim-Belegundu Arora). The former is used to obtain approximate equation of stress and displacement of a structure. The latter is used to solve approximate optimization. This algorithm uses second-order information of a function and active set strategy. This program is connecting ANSYS and PLBA. And it progress the process repeatedly until it obtain optimum value. As a method of approximate optimization, sequential design domain(SDD) is introduced. SDD starts with a certain range which is offseted from midpoint of an initial design domain and then SDD of the next step is determined by optimal point of a prior step.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.1
• /
• pp.1-7
• /
• 2015

A gutter is generally a fixed beneath the edge of a roof to carry off rainwater, or a narrow trough that collects rainwater from the roof of a building to diverts it from the structure, typically into a drain. Reasonable designs reduce the mass of the gutters (~ 16.9%), make it faster and easier to assemble, and gives it consistent strength and integrity (about 10%). New gutter systems are presented according to the results of structural analyses performed by ANSYS and ADAMS/Durability Hot Spots. In addition, the CATIA program can improve the precision of the 3D system simulations. The design of a gutter system installations also needs to comply with the specific rainfall intensities and adequate overflow provisions needs to be provided to prevent water from sides of the roofs during heavy rainfall periods. The principle outcome of this work is a computational design tool that can be used to improve the gutter performance considering a variety of factors (gutter geometry, drainage and rainfall intensity). A good gutter design must satisfy many criteria, including durability, low cost, and ease of repair and cleaning.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.337-341
• /
• 1997

The purpare of this research is to develope a FEM program for analyzing solidification processes of axisymmetic casting, considering phase changes and the contact between the metal and mold. Temperture recovery method is employed for considering the phase changes releasing the latent heat. A gap element is employed for modeling the interface between the model and metal in finding deformed shapes. In order to verify the developed program, an axisymmetric aluminum casting processes is simulated. Temperature distribution, phase front position, and shrinkaga and porosity creation are compared with measurement, FIDAP results, and ANSYS results, and good agreements are examined.

• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.2
• /
• pp.350-355
• /
• 2016

This research aims to evaluated the structure improvement and new product development of valve tester. A valve tester was redesigned for structure improvement and new product development using 3-D design program CATIA. In addition, behavior analysis was conducted on the modeled valve tester using the ANSYS program. The total deformation, stress and strain were obtained by the internal pressure change. This result was applied to the new product development of valve tester.

• Journal of Welding and Joining
• /
• v.9 no.3
• /
• pp.41-51
• /
• 1991

The thermomechanical coupling phenomena in the resistance welding process is complicated due to interactions of mechanical, thermal and electrical factors. Although experimental investigations of resistance spot welding have been carried out, but there are a few by computer simulation. so the purpose of this research is to decrease the time and cost much required in experimental investigation by carrying out the analysis of the resistance spot welding process through computer simulation based on the finite element method. The tool used in the computer simulation is the commercial ANSYS program package. A two dimensional axisymetric model is used to simulate the resistance spot welding for two stainless steel sheets of equal thickness and parametric study is carried out for variable welding current, workpieces of unequal thickness and dissimilar materials. The results from the computer simulation are in good agreement with the experimental one. Through these results, such items as stress distribution, temperature profiles, thermal expansion and weld nugget formation are predicted. Reliability and applicability of finite element models have been demonstrated to simulate and to analyze the resistance spot welding process.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2881-2892
• /
• 2024

Annular flow refers to a special type of two-phase flow pattern in which liquid flows as a thin film at the periphery of a pipe, tube, or conduit, and gas with relatively high velocity flows at the center of the flow section. This gas also includes dispersed liquid droplets. The liquid film flow rate continuously changes inside the tube due to two processes-entrainment and deposition. To determine the liquid holdup, pressure drop, the onset of dryout, and heat transfer characteristics in annular flow, it is important to have proper knowledge of flow characteristics. Especially a better understanding of entrainment fraction is important for the heat transfer and safe operation of two-phase flow systems operating in an annular two-phase flow regime. Therefore, the objective of this work is to develop a computational model for the simulation of the annular two-phase flow regime and assess the various existing models for the entrainment rate. In this work, Computational Fluid Dynamics (CFD) in ANSYS FLUENT has been applied to determine annular flow characteristics such as liquid film thickness, film velocity, entrainment rate, deposition rate, and entrainment fraction for various gas-liquid flow conditions in a vertical upward tube. The gas core with droplets was simulated using the Discrete Phase Model (DPM) which is based on the Eulerian-Lagrangian approach. The Eulerian Wall Film (EWF) model was utilized to simulate liquid film on the tube wall. Three different models of Entrainment rate were implemented and assessed through user-defined functions (UDF) in ANSYS. Finally, entrainment for fully developed flow was determined and compared with the experimental data available in the literature. From the simulations, it was obtained that the Bertodano correlation performed best in predicting entrainment fraction and the results were within the ±30 % limit when compared to experimental data.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.266-268
• /
• 2015

In this paper, we write about EDISON program. We study about where to use this program. We can use this program for FEA naturally. But we study that using this program in class. Many students can't understand many mechanics of materials' problem. They want to see image such as change of beam. It can help students to understand many problem. We can use ANSYS or Abaqus. But EDISON program is better for students because of it is freeware. In this paper, I write two problem. One is peak stress of basic beam, another is shearing stress flow of I-beam. On the basis of this, EDISON program will be widely used.