• Journal of Welding and Joining
• /
• 제10권4호
• /
• pp.222-229
• /
• 1992

A prediction of penetration and heat affected zone by using Finite Element Method in CO$_{2}$ Arc Welding has been discussed this paper. The temperature distribution of a base metal produced by the CO$_{2}$ arc welding processing is analyzed by using a three dimensional finite element model. The common finite element program ANSYS 4.4A was employed to obtain the numerical results. Temperature dependent material properties, effect of latent heat, and the convective boundary conditions are included in the model. Numerically predicted sizes of the penetration and the heat affected zone are compared with the experimentally observed values. As a result, there was a slight difference between numerical analysis values and experimentally observed values. For in the case of heat affected zone, it was not considered a precise forced convective coefficient value, and in the case of penetration, it was not, considered a arc force.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.393-397
• /
• 2001

A linear ultrasonic motor was designed by a combination of the first longitudinal and fourth bending mode, the motor consisted of a straight aluminum alloys bar bonded with a piezoelectric ceramics element as a driving element. That is, L$_1$-B$_4$ linear ultrasonic motor can be constructed using a multi-mode vibrator of longitudinal and bending modes. The simulation with variation of material characteristics of piezoceramic were performed as use of finite element analysis ANSYS 5.5, such as elastic compliance, piezoelectric constant, electro-mechanical coupling coefficient, poisson's ratio and density. The results of simulation, elastic compliance constant s$_{11}$ and piezoelectric constant d$_{31}$ had the most of influence on the elliptic-motion. This results consist with using transverse effect of material. The used motor were piezoceramics of 4 layers, and the dimensions were 65$\times$5$\times$3.5mm(LxWxt).).

• Structural Engineering and Mechanics
• /
• 제22권4호
• /
• pp.433-447
• /
• 2006

The problem of very large deflection of a circular cantilever arc device subjected to inward or outward polar force is studied. An exact elliptic integral solution is derived for the two cases and the results are checked using large displacement finite element analysis via the ANSYS package by performing a new novel modeling simulation technique for this problem. Excellent agreements have been obtained between the exact analytical solution and the numerical approach. From this study, a design chart for engineers is developed to predict the required value for the inward polar force for the device to switch on for a given angle forming the circular arc (${\theta}_o$). This study has several interesting applications in mechanical engineering, integrated circuit technology, nanotechnology and especially in microelectromechanical systems (MEMs) such as a MEM circular device switch subjected to attractive or repulsive magnetic forces due to the attachments of two magnetic poles at the fixed and at the free end of the circular cantilever arc switch device.

• Steel and Composite Structures
• /
• 제24권4호
• /
• pp.383-390
• /
• 2017

This paper highlights the experimental and numerical investigations performed on a tubular T-joint fabricated from circular hollow sections under axial compressive loads applied at the brace. Tests were performed on a reference joint and the joint wrapped with Carbon Fiber Reinforced Polymer (CFRP). The Nitowrap EP carbon fiber with Nitowrap 410 resin serve as a composite material is used for wrapping the T-joint. Schematic diagram of the fabricated tubular joint for the experimental test setup, along with the experimental and numerical results are presented. After performing these experiments, it has been demonstrated that the joint wrapped with CFRP has a better strength and lesser deflection than a reference joint. Finite element analysis carried out in Ansys reveals that the results were in good correlation with the experimental values.

• 한국가시화정보학회지
• /
• 제9권4호
• /
• pp.22-27
• /
• 2011

In this study, we present methods of coupling a commercial code, ANSYS CFX, and the user Fortran codes for solving an unsteady electro-osmotic flow around a pair of electrodes, receiving DC, attached to the top and the bottom walls of a two-dimensional cavity. We developed a module of Fortran programs for solving the ion-transport equations as well as the Poisson equations for the potential to be used in coupling with the CFX. We present how the developed codes are applied to solving the transient DC electro-osmotic flow problem within a simple cavity. We also address various problems encountered during the development process and explain why such problems are raised.

• Structural Monitoring and Maintenance
• /
• 제3권4호
• /
• pp.335-347
• /
• 2016

One of major errors in flow rate measurement for two-phase flow using an Electrical Capacitance Sensor (ECS) concerns sensor sensitivity under temperature raise. The thermal effect on electrical capacitance sensor (ECS) system for air-water two-phase flow monitoring include sensor sensitivity, capacitance measurements, capacitance change and node potential distribution is reported in this paper. The rules of 12-electrode sensor parameters such as capacitance, capacitance change, and change rate of capacitance and sensitivity map the basis of Air-water two-phase flow permittivity distribution and temperature raise are discussed by ANSYS and MATLAB, which are combined to simulate sensor characteristic. The cross-sectional void fraction as a function of temperature is determined from the scripting capabilities in ANSYS simulation. The results show that the temperature raise had a detrimental effect on the electrodes sensitivity and sensitive domain of electrodes. The FE results are in excellent agreement with an experimental result available in the literature, thus validating the accuracy and reliability of the proposed flow rate measurement system.

• 스마트미디어저널
• /
• 제4권4호
• /
• pp.64-69
• /
• 2015

본 논문에서는 UWB 통신 시스템의 테이퍼드 슬롯 안테나를 제안하였다. 테이퍼드 슬롯 안테나는 넓은 대역폭 특성과 진행파 안테나의 지향성 방사를 갖는다. 제안된 테이퍼드 슬롯 안테나는 Ansys사의 HFSS를 사용하여 설계하였으며, 반사손실 및 정재파비, 방사패턴 등을 분석하였다. 안테나의 동작 대역은 2.7 ~ 4.8 GHz 대역에서 -10 dB S11 및 $VSWR{\leq}2$(2.1 GHz)를 만족하였다. 안테나의 방사패턴은 E-평면(YZ plane)과 H-평면(XZ plane)에서 특정한 방향으로 신호를 전송하는 지향성 방사패턴을 보였으며, 이득은 4.5 GHz 대역에서 7.3 dBi의 높은 이득을 보였다. 따라서 제안된 테이퍼드 슬롯 안테나는 넓은 대역폭 특성과 위치인식에 적합한 지향성의 특성을 보인다.

• 한국강구조학회 논문집
• /
• 제25권4호
• /
• pp.359-368
• /
• 2013

본 논문은 중공튜브 및 샌드위구조 형식을 주로 갖는 GFRP 복합소재 바닥판의 기본설계에서 전체 유한요소 모델링을 이용하지 않고 탄성등가 모델링을 이용한 간편 해석 방법을 제시하였다. 제시된 간편 해석 방법의 타당성 검증을 위해서 ANSYS 프로그램이 사용되었으며, 전체 유한요소 모델링과 탄성등가모델링을 이용한 해석값을 각각 비교하였다. 또한 본 논문에서 제안된 GFRP 복합소재 바닥판 간편 해석법에 의한 해석 결과를 비교하기 위해 각형 튜브를 갖는 샌드위치 구조형식 GFRP 복합소재 바닥판의 4점 휨시험인 실내실험결과를 수행하였다. 해석 결과와 실험 결과 내용을 비교분석하였다. 제시된 간편해석 방법은 GFRP 복합소재 바닥판의 기본설계시 사용하기에 적용성이 있음을 확인되었다.

• 한국산업융합학회 논문집
• /
• 제7권4호
• /
• pp.355-361
• /
• 2004

The finite element method were used to determine the stress intensity factor of cracked plate. The stress method, displacement method and J Integral are most popular finte element method. ANSYS proposed another a kind of displacement method. In this paper, it was examined that the accuracy and utility of the ANSYS method could believable to determine the stress intensity factors of centered inclined crack. Generally, inclined crack has two portion of stress intensity factors, tensile mode F1 and shear mode F2. For the purpose of increasing the accuracy of stress intensity factors, examined the effect of the numbers of nodes and elements, crack tip element size and number of partition of the crack tip vicinity. It was found that the method proposed by ANSYS is useful and has high accuracy. Accuracy of calculated stress intensity factors was increased by increase of the number of nodes and elements, and at the small size of crack tip elements can get more highly accuracy.

• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.28-37
• /
• 2000

In this paper the LNG vessel of the Moss type which is capable of lifting 15,261 tons is investigated in the view point of the pressure vessel preliminary design using the finite element method. The Pressure vessel design is based on the equivalent stress levels due to the internal pressure. The finite element model of the spherical pressure vessel is configured using 4 noded quadrilateral shell element. The finite element analysis program NASTRAN and ANSYS 5.5are implemented. The design is compared with the three kinds of the boundary condition : first, where the equator of the pressure vessel is fixed, and where the top and is fixed, and, the bottom end is fixed, respectively. A comparison is presented between the results obtained by the finite element model and by the prototype production model. Additionally just below position(case 1 & case 2) of equator ring was carried out by using ANSYS 5.5. The results show that the vessel design based on the stress is acceptable at the preliminary design.