• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.41-41
• /
• 2009

To evaluate the applicability of dissimilar joining between Mg and Al alloys in automobile manufacturing process, solid state joining processes such as magnetic pulse welding(MPW), friction stir welding(FSW) and friction spot joining(FSJ) were attempted successfully. MPW process has been concentrated mainly on round section tube to tube and tube to bar welds. AZ31 Mg alloy has been successfully welded to pure Al A1070 as well as to Al alloy A3003. While, for friction stir welding of dissimilar sheet joints, AZ31B/A6061 with the thickness of 2mm were used and a square butt joint with a good quality was obtained at the conditions of 0.8mm/sec of travel speed and tool rotation speed of 850rpm. The maximum tensile strength of 179 MPa, which was about 80 % of the Mg base metal tensile strength, has been obtained. Finally, friction spot joining was attempted to make a dissimilar lap joint between AZ31(0.8mm) and A6061(1mm), while the joint exhibited the same level of tensile shear strength as that of similar Mg joint.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.5
• /
• pp.34-39
• /
• 2010

The characteristic evaluation of an aluminium filler tube for automotive is presented in this paper. The material of filler tube was used AL3003 aluminium. In characteristic evaluation of an aluminium filler, we measured the corrosion, chemical resistance, weight, leak, welding strength, exciting endurance, and the solt spray test etc.. It has been shown that the weight decreased approximately 61% in aluminum filler tube developed comparing with steel filler tube. As the characteristic evaluation on the manufactured aluminium filler it was enough satisfied to use at the automotive filler tube.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.8
• /
• pp.87-92
• /
• 2022

The Al3003 aluminum plate was cut by grinding, milling, sawing, and shearing, and the hard-anodizing surface of the material was investigated. Large burrs were formed during grinding and milling. The brittle anodized film split and migrated along the deformed aluminum surface. During shearing, the hard-anodized film on the blade entry surface cracks and slides along the deforming aluminum. The cutting heat increased the ductility of the aluminum and further promoted burr formation. The oil-based coolant suppressed burrs and prevented chips from sticking to the endmill. It is better to avoid the high cutting speed and slow material feed rate conditions, which increase the cutting temperature and burr in the band saw.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.3_4
• /
• pp.364-372
• /
• 2003

In this study, the characteristics of catechol tannin and pyrogallol tannin contained in Pteridium aquilinum were analysed by It spectrum. Silk fabrics were dyed with Pteridium aquilinum extracts using various mordants, and their dyeing properties were discussed. Additionally the fastness the water digestion, perspiration liquid digestion and light irradiation were investigated. IR spectrum of catechol tannin showed bands of O-H at $3417cm^{-1}$, C-H at $2930cm^{-1}$, C=0 at $1722cm^{-1}$, C=C at $1644cm^{-1},\;CH_2\;at\;1402cm^{-1}$. And IR spectrum of pyrogallol tannin showed bands of O-H at $3409cm^{-1}$, C-H at $3003cm^{-1}\;and\;2933cm^{-11}$, C=0 at $1701cm^{-1}$, C=C at $1582cm^{-11},\;CH_2\;at\;1410cm^{-1}$, CO at carboxylic acid and carboxylic acid ester at $1287cm^{-1}\;and\;1135cm^{-1}$. The maximum absorption wavelength of the extracts appeared at 270.0nm and 311.5nm. The optimum conditions for dyeing silk fabric with Pteridium aquilinum extracts were $80^{\circ}C$, 60min. Surface color of the silk fabric dyed with Pteridium aquilinum extracts was 2.7Y Surface color of the pre-mordanted fabrics with Al, Cu and Fe were 4.3Y, 2.5Y and 4.7Y, respectively. And Surface color of the post-mordanted fabrics with Al, Cu and Fe were 3.7Y, 2.8Y and 0.2GY. The water fastness and the alkaline perspiration fastness were improved in the Al-mordanted silk fabrics. By acidic and alkaline perspiration treatment, ${\Delta}E of the unmordanted fabrics was lower than hat of pre- and post- mordanted fabrics. Also after 40hour irradiation, ${\Delta}E of the unmordanted fabrics was lower than that of pre- and post- mordanted fabrics.

• The Journal of the Petrological Society of Korea
• /
• v.4 no.1
• /
• pp.31-48
• /
• 1995

The Jurassic Kwanaksan stock, so far known to be composed of biotite granite only, has the mineral assemblage of quartz+K-feldspar+plagioclase+biotite${\pm}$gernet. The lithology of the stock is classified as alkali feldspar granite by their mode and plagioclase compositions (An<5). Subsolvus feldspars, rather early crystallization of biotite, and shallow emplacement depth estimated from Q-Ab-Or diagram suggest hydrous nature of the magma, which contrasts with anhydrous A-type like geochemistry described below. Major and trace element compositions of the Kwanaksan stock are distinct from those of the adjacent Seoul batholith, suggesting a genetic difference between the two, The Kwanaksan stock shows geochemical characteristics similar to A-type granite in contrast to most other Mesozoic granites in Korea, in that it has high $SiO_2$(73~78wt%), $Na_2O+K_2O$, Ga(27~47 ppm). Nb(22~40 ppm), Y(48~95 ppm), Fe/Mg and Ga/Al, and low CaO(<0.51 wt%). Ba (8~75 ppm) and Sr(2~23 ppm). However, it has lower Zr and LREE and higher Rb(384~796 ppm) than typical A-type granite. LREE-depleted rare earth element pattern with strong negative Eu anomaly of previous studies is reinterpreted as representing source magma characteristics. The residual material during partial melting is not compatible with pyroxenes, amphibole or garnet, while significant amount of plagioclase is required. Similarity of geochemistry of the Kwanaksan stock to A-type granite suggests the origin of the stock has a chose relationship with that of A-type granite. These observations lead us to propose that the Kwanaksan stock was formed by partial melting of felsic source rock.