• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.1
• /
• pp.7-14
• /
• 2023

We investigated the effect of multiple tempering on the microstructure and mechanical properties of AISI 4340 steel. The austenitized and quenched AISI 4340 steels were tempered at 550, 600, and 650℃ for 1, 2, and 4 h by single-tempering (ST). The multiple tempering was conducted for 4 h by double-tempering (DT, 2 h + 2 h), and quadruple-tempering (QT, 1 h + 1 h + 1 h + 1 h). As tempering temperature increases, yield strength and ultimate tensile strength decrease and elongation increases due to recovery and recrystallization of martensite and coarsening of carbides. At 550℃, as the number of tempering cycles increases, the yield strength and tensile strength decrease at the expense of fracture elongation. At 600 and 650℃, the yield strength and tensile strength increase with increasing the number of tempering cycles while fracture elongation maintains similar values. The multiple tempering at the same tempering time of 4 h improves the modulus of toughness at all tempering temperatures, which is presumed to be due to the change in carbide precipitation behavior by multiple tempering.

• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.4
• /
• pp.22-28
• /
• 1991

The crevice corrosion behavior on austenitic AISI 304 and 316L stainless steel welded by TIG, MIG, $CO_2$ and SMA was studied. The results are as follows : In 10% $FeCl_3$ solution and natural sea water sampled near Mokpo port, the base metal of 304 stainless steel showed small amount corrosion, whereas 316L stainless steel did not showed any corrosion in the test periods. The weight loss caused by crevice corrosion increased with increasing weld heat input and residual .delta. ferrite formed in welded part. The corrosion resistance of the welded part was in the order of TIG, MIG, $CO_2$ and SMA. From this tendency, it is proved that the smaller heat input gives the better corrosion resistance.

• Journal of Welding and Joining
• /
• v.5 no.1
• /
• pp.34-41
• /
• 1987

To explore the possible application of thermal analysis technique as a probe for finding weld defects, Hydrogen trapping phenomena in Heat Affected Zone (HAZ) of the AISI 5160 spring steel were investigated. HAZ was divided into five parts, which were used as thermal analysis specimens. Two types of trap sites were found in HAZ, ferrite/cementin interface and microvoid. The thermal analysis peak due to the ferrite/cementite interface increased its height toward the weld deposit. The thermal analysis peak due to the microvoid was the highest where the grain size was the smallest. The correspondence between the cold cracking and hydrogen trap nature is also discussed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.05a
• /
• pp.143-146
• /
• 2001

The evolution of dynamic recrystallization (DRX) was studied with torsion test for AISI 304 stainless steel in the temperature range of $900-1000^{\circ}C$ and strain rate range of 0.05-5/sec. The evolution of DRX was investigated with microstructural analysis and change of flow stress curve slope. The investigation of serrated grain boundaries using electron back scattered diffraction (EBSD) analysis indicated that the nucleated new DRX grain size was similar to the size of bulging part. Before the steady state, the dynamically recrystallizing grains do not remain a constant size and gradually grow to the size of fully DRX grain at steady state. The calculation of grain size was based on $X_{DRX}$ and the assumption, which the nucleated DRX grains are growing to the steady state, continuously. It was found that the calculated results agreed with the microstructure of the alloy.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.40-45
• /
• 2008

This study describes tensile test results under room and elevated temperatures for AISI 304 stainless steel which is widely used for a airframe structural material. Tensile tests were conducted according to ASTM standards. Reliability analysis was conducted by using normal probability paper to evaluate A and B basis tensile strengths applicable to airframe structural design.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.1
• /
• pp.137-146
• /
• 2008

Nd:YAG pulse laser welding of stainless steel plate was simulated to find welding condition by using commercial finite element code MARC. Due to geometric symmetry, a half model of AISI 304 stainless steel plate was considered and user subroutines were applied to boundary condition for the heat transfer. Material properties such as conductivity, specific heat, mass density and latent heat were given as a function of temperature. As results, Three dimensional heat source model for pulse laser beam conditions of butt welding has been designed by the comparison between the finite element analysis results and experimental data on AISI 304 stainless steel plate. Nd:YAG laser welding for AISI 304 stainless steel was successfully simulated and it should be useful to determine optimal welding condition.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.802-806
• /
• 2001

Chrome-molybden steel or chrome steel for machine structural use been shown to excellent hardenability adding boron of a small amount at low carbon steel. In the country boron steel has been used widely high strength volt and wear resistant components of construction equipment. SEM results showed classical fatigue fractures, consistent with surface crack initiation. The speciments were cycled using under load controlled rotary bending fatigue tests. In this study, the fatigue crack initiation as well as the fatigue crack growth behavior and the fracture mechanism were investigated through observations of fracture surface boron steel(AISI 51B20).

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.7
• /
• pp.872-878
• /
• 2003

As the results of recent industrial development, many industrial plants and marine structures are exposed to severe corrosion environment than before. Especially, under the wet environment, crevice corrosion damage problems necessarily occur and encourage many interests to prevent them. In this study, the electrochemical polarization test was carried out to study characteristics of crevice corrosion for AISI 304 stainless steel in various solution temperatures. The results are as follows ; 1) as the solution temperature increased in IN $\textrm{H}_2\textrm{SO}_4$, the passive current density and critical current density were increased, whereas corrosion potential and break down potential were nearly constant, 2) as the solution temperature increased. the induced time for initiation of crevice corrosion was shortened. 3) The potential range in the crevice was -220mV/SCE to -380mV/SCE according to the distance from the crevice opening, which is lower than that of external surface of -200mV/SCE.

• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.45-47
• /
• 2004

We have investigated the microstructures and the mechanical properties of TiA1/Cerameti1721 (Ag-Cu-Ti insert metal)/AISI4140 joints at 800$^{\circ}C$ for 60 to 300s using induction brazing method. Two continuous reaction layers of AICuTi and AICu$_2$Ti were formed at the interface between the braze and TiAl, whose thickness increased with the brazing time. The braze consisted of Ag-rich, Ti-rich, CuTi and CuTi$_2$ phases. The maximum tensile strength achieved 296MPa, which was 71% of that of TiAl base metal, for the specimen bonded at 800$^{\circ}C$. Further increase of the brazing temperature and time resulted in constant deterioration of its bonding strength due to large amount of brittle IMC.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.8
• /
• pp.839-846
• /
• 2007

Nd:YAG pulse laser fillet welding of stainless steel plate was simulated to find welding condition by using commercial finite element code MARC. Full model of AISI 304 stainless steel plate was considered and user subroutines were applied to boundary condition for the heat transfer. Material properties such as conductivity, specific heat, mass density and latent heat were given as a function of temperature. As results, Three dimensional heat source model for pulse laser beam conditions of fillet welding has been designed by the comparison between the finite element analysis results and experimental data on AISI 304 stainless steel plate. Nd:YAG laser welding for AISI 304 stainless steel was successfully simulated and it should be useful to determine optimal welding condition.