The Transactions of the Korean Institute of Electrical Engineers P
/
v.51
no.3
/
pp.120-125
/
2002
The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. In the switching-mode power converter, the output voltage is generally controlled by varying the duty ratio of main switch. When a converter operates in steady state, duty ratio of the converter is kept constant. So the power of switching noise is concentrated in specific frequencies. Generally, to reduce the EMI and improve the immunity of converter system, the switching frequency of converter needs to be properly modulated during a rectified line period instead of being kept constant. Random Pulse Width Modulation (RPWM) is performed by adding a random perturbation to switching instant while output-voltage regulation of converter is performed. RPWM method for reducing conducted EMI in single switch three phase discontinuous conduction mode boost converter is presented. The more white noise is injected, the more conducted EMI is reduced. But output-voltage is not sufficiently regulated. This is the reason why carrier frequency selection topology is proposed. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300V/1kW with 5%~30% white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with LISN, which are connected to the spectrum analyzer respectively.
Journal of the Institute of Electronics Engineers of Korea CI
/
v.47
no.4
/
pp.63-70
/
2010
In IEEE 802.11e system providing differentiated services, there exist some problems as follows; collision probability increase due to the increase in the number of nodes by employing CSMA/CA transmission mode, transmission speed declining tendency towards the worst of it, which is caused by different transmission mode and decrease of TCP transmission rate as the result of the link occupancy by UDP when TCP shares the link with UDP by the TCP’s flow control characteristic. In this thesis, the initial minimum and maximum CW are set differently according to the number of connected nodes in the network to avoid collisions and TXOP is adjusted according to the channel state, in which ACs with low priority but better channel state will get gradually more chances to transmit leading to optimal channel capacity. Also, by allowing higher priority for ACK frames which control the TCP transmission, the flow control becomes better because that reduces the channel occupancy by UDP flow, and by this, fair transmission is obtained from the result of the more fair transmission and active resource allocation.
Journal of the Korea Fashion and Costume Design Association
/
v.22
no.1
/
pp.33-44
/
2020
The purpose of this study is to guide the research direction for securing the competitiveness of the textile industry by analyzing the trends of patent technology development for flexible materials and platform technologies of domestic and overseas textiles used for wearable devices. The study is based on patents from Korea (KIPO), USA (USPTO), Japan (JPO), Europe (EPO), PCT (WO), and China (SIPO), which were registered as of December 31, 2017. The analysis utilized 3,643 patents acquired from the WINTELIPS search DB. The technology classification system for patent analysis was divided into evangelist-based textile technology developments: human body (AA), fiber attachment patch development (AB), and service platform development (AC). The analysis findings are as follows: 1. The development of flexible materials and platform technologies for textile-based wearable devices has increased since 2000. In particular, China (SIPO) had the most patents. 2. In China, Japan, and Korea, most patent applicants are applied for by natives, but the US has a high proportion of foreigners applying for patents. 3. As for the amount of development of the evangelist-based textile technology (AA) was the most common with 1,203 (33%) cases. As a result of the above IP historical analysis, it can be seen that as a result of the global competition, domestic companies need to acquire IRP and standard technology, and promote commercialization by applying their products to smart wearables devices and other products.
The recent Fukushima nuclear power plant accidents shows that the core make up at high RCS pressure condition is very important to prevent core melting. The core make up flow at high pressure condition should be driven by gravity force or passive forces because the AC-powered safety features are not available during a Station Black Out (SBO) accident. The reactor Coolant System (RCS) mass inventory is continuously decreased by releasing steam through the pressurizer safety valves after reactor trip during a SBO accident. The core will be melted down within 2~3 hours without core make up action by active or passive mode. In the new design concept of a Hybrid Safety Injection Tank (Hybrid SIT) both for low and high RCS pressure conditions, the low pressure nitrogen gas serves as a charging pressure for a LBLOCA injection mode, while the PZR high pressure steam provides an equalizing pressure for a high pressure injection mode such as a SBO accident. After the pressure equalizing process by battery driven initiation valve at a high pressure SBO condition, the Hybrid SIT injection water will be passively injected into the reactor downcomer by gravity head. The SBO simulation by MARS code show that the core makeup injection flow through the Hybrid SIT continued up to the SIT empty condition, and the core heatup is delayed as much.
Kim, Young Jin;Park, Tae Il;Kim, Hyun Soon;Suh, Sug Kee;Kim, Hag Sin;Yun, Song Joong
Journal of Plant Biotechnology
/
v.6
no.2
/
pp.91-96
/
2004
The use of liquid-medium-based procedure relative to the solid media led to a 4.5-fold increase in the number of cotyledon-stage embryos. The most efficient system for multiplication and regeneration of somatic embryos was CP6 procedure with the media MSD40/MSD20/MSM6AC/FNL0S3S3GM. However, the rate of regeneration was lower. About 71% of the embryos with dicotyledon were continued to develop the roots after desiccation treatment and 92% of the germinated embryos produced shoots in 10 days. Of the four morphologically different types of embryos, dicotyledonous ones showed a high frequency of conversion, while only a few with fused and horn type cotyledon developed shoots. Mature somatic embryos were desiccated in empty petri dishes for 12-72 h. Embryo survival rate was the highest after 12 h of desiccation, but maximal germination was observed at 24 h. After desiccation, they were placed on MS medium without growth regulators for germination. Germinating embryos were transferred to small pots with vermiculite for plant regeneration. The etiolating the plants during the growth was resolved to add 1% activated charcoal on hormone-free MS medium.
Notch signaling plays a crucial role in development of the nervous system. Neurodevelopmental hypothesis on etiology of schizophrenia has been implicated. The aim of this study is to determine whether single nucleotide polymorphisms (SNPs) of Notch homolog 4 (Drosophila) (NOTCH4) gene are associated with schizophrenia. This study included 283 schizophrenia patients diagnosed according to DSM-IV and 301 normal control subjects. Control subjects without history of psychiatric disorders were recruited. Four missense SNPs [rs915894 (exon 3, Lys117Gln), rs2071282 (exon 4, Pro204Leu), rs422951 (exon 6, Thr320Ala), and rs17604492 (exon 18, Gly942Arg)] of NOTCH4 gene were genotyped by the direct sequencing method. Multiple logistic regression models (codominant, dominant, and recessive models) were employed to evaluate odds ratio, 95% confidence interval, and p value. For analysis of genetic data, SNPStats, Haploview, HapAnalyzer, SNPAnalyzer, and Helixtree programs were also used. Of 4 SNPs, rs2071282 was weekly associated with schizophrenia in two alternative models (codominant model, P=0.049; dominant, P=0.041). However, these associations were not significant after Bonferroni correction. At 4 SNPs, one linkage disequilibrium (LD) block was made. This block consisted of rs915894 and rs2071282. In haplotype analysis, AC haplotype was weakly associated with schizophrenia (dominant, P=0.04). This association was disappeared after Bonferroni correction. Our result shows possibility that some SNPs of NOTCH4 gene may be weekly associated with development of schizophrenia in Korean population. However, replication result by other population will be needed.
Journal of Advanced Marine Engineering and Technology
/
v.10
no.2
/
pp.156-164
/
1986
In the case of boiling on high temperature wall, vapor film covers fully or parcially the surface. This phenomenon, film boiling or transition boiling, is very important in the surface heat treatment of metal, design of cryogenic heat exchanger and emergency cooling of nuclear reactor. Mainly supposed hydraulic-thermal accidents in nuclear reactor are LCCA (Loss of Coolant Accident) and PCM (Power-Cooling Mismatch). Recently, world-wide studies on reflooding of high temperature rod bundles after the occurrence of the above accidents focus attention on wall temperature history and required time in transient cooling process, wall superheat at rewet point, heat flux-wall superheat relationship beyond the transition boiling region, and two-phase flow state near the surface. It is considered that the further systematical study in this field will be in need in spite of the previous results in ref. (2), (3), (4). The paper is the study about the fast transient cooling process following the wall temperature excursion under the CHF (Critical Heat Flux) condition in a forced convective subcooled boiling system. The test section is a vertically arranged concentric annulus of 800 mm long and 10 mm hydraulic diameter. The inner tube, SUS 304 of 400 mm long, 8 mm I.D, and 7 mm O.D., is heated uniformly by the low voltage AC power. The wall temperature measurements were performed at the axial distance from the inlet of the heating tube, z=390 mm. 6 chromel- alumel thermocouples of 76 .mu.m were press fitted to the inner surface of the heating tube periphery. To investigate the heat transfer characteristics during the fast transient cooling process, the outer surface (fluid side) temperature and the surface heat flux are computed from the measured inner surface temperature history by means of a numerical method for inverse problems of transient heat conduction. Present cooling (boiling) curve is sufficiently compared with the previous results.
This study was planned to see whether the Panax Ginseng root has any influence upon the emotionality in rats exposed to a novel open-field and induced by a grid shock. Sixty four male albino rats whose body weight ranged from 130 to 180 gm were used. They were divided into four groups, i.e., placebo control group, 5mg/kg Ginseng ext. group, 10mg/kg Ginseng ext. group, and 20mg/kg Ginseng ext. group. Sixteen rats were subjected in each group. Open-field activity was measured in a $2.20m\;{\times}\;2.20m$ open-field that was divided into 15cm squares. Four novel objects and food pellets were put with an equal distance in the open-field. Locomotion was recorded by entering the number of squares traversed for 4 min. and behaviors which were shown at the 10-sec. period were checked by a modified Jarrad and Bunnel's observation procedure. Sensitivity to the grid shock was measured in a compartment of shuttle box. 10, 20, 30, 40, 50, 60 and 70 volt ac. 2 sec., electric shock were delivered in each subject by the grid to animal's feet. Flinch, vocalization and jumping responses were rated in each shock level. The results obtained were as follows: 1.) 5mg/kg and 10mg/kg Ginseng ext. groups were tended to increase the ambulation and exploration compared with placebo control. 2.) All Ginseng extract groups were defecated significantly less often than placebo control in the open-field and shock situation. 3.) Thresholds to the electric shock were tended to elevate in all Ginseng groups. 4.) These results suggest that Ginseng extract has a stimulant action in open-field and a tranqulizing action in feared situation.
$Potato$$virus$$X$ (PVX) replication is precisely regulated by regulatory viral sequences and by viral and/or host proteins. In a previous study, we identified a 54-kDa cellular tobacco protein that bound to a region within the first 46 nucleotides (nt) of the 5' non-translated region (NTR) of the viral genome. Optimal binding was dependent upon the presence of an ACCA sequence at nt 10-13. To identify host factors that bind to 5' NTR elements including AC-rich sequences as well as stemloop 1 (SL1), we used northwestern blotting and matrixassisted laser desorption/ionization time-of-flight mass spectrometry for peptide mass fingerprinting. We screened several host factors that might affect PVX replication and selected a candidate protein, $Nicotiana$$tabacum$ WRKY transcription factor 1 (NtWRKY1). We used a $Tobacco$$rattle$$virus$ (TRV)-based virus-induced gene silencing (VIGS) system to investigate the role of NtWRKY1 in PVX replication. Silencing of $WRKY1$ in $Nicotiana$$benthamiana$ caused lethal apical necrosis and allowed an increase in PVX RNA accumulation. This result could reflect the balancing of PVX accumulation in a systemic $N.$$benthamiana$ host to maintain PVX survival and still produce a suitable appearance of mosaic and mottle symptoms. Our results suggest that PVX may recruit the WRKY transcription factor, which binds to the 5' NTR of viral genomic RNA and acts as a key regulator of viral infection.
Journal of the Korean Society for Precision Engineering
/
v.19
no.4
/
pp.93-100
/
2002
The current from the feed motor of a machine tool contains substantial information about the machining state. There have been many researches that investigated the current as a measure for the cutting farces. However it has been reported that this indirect measurement of the cutting farces from the feed motor current is only feasible in low frequency. In this research, it was presented that the bandwidth of the current monitoring can be expanded to 130 Hz. And the unusual behavior of the current was examined in this bandwidth. The cross-feed directional cutting force influences the machined surface of the workpiece, which makes it necessary to estimate this force to control the roughness of the machined sulfate. The current exists in the stationary feed motor, and it can give the useful information on the quality of the machined surface. But the unpredictable behavior of the current prevents applying the current to prediction of the cutting state. Empirical approach was conducted to resolve the problem. As a result, the current was shown to be related to the accumulation of the accumulation of the infinitesimal rotation of the motor. rotation of the motor. Subsequently the relationship between the current and the cutting force was identified.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.