• Nuclear Engineering and Technology
• /
• 제55권12호
• /
• pp.4664-4670
• /
• 2023

Radiation is the main safety issue for almost all nuclear applications, which must be controlled to protect living organisms and the surrounding materials. In this context, radiation shielding materials have been investigated and used in nuclear technologies. The choice of materials depends on the radiation usage area, type, and energy. Polymer materials are preferred in radiation shielding applications due to their superior characteristics such as chemical inertness, resistivity, low weight, flexibility, strength, and low cost. In the presented work, ABS polymer material, which is possibly the most commonly used material in 3D printers, is mixed with Gd₂O₃ and Er₂O₃ nanoparticles. ABS filaments containing these rare-earth elements are then produced using a filament extruder. These produced filaments are used in a 3D printer to create shielding samples. Following the production of shielding samples, SEM, EDS, and gamma-ray shielding analyses (including experiments, WinXCOM, GEANT4, and FLUKA) are performed. The results show that 3D printing technology offers significant enhancements in creating homogeneous and well-structured materials that can be effectively used in gamma-ray shielding applications.

• Journal of Welding and Joining
• /
• 제32권4호
• /
• pp.20-25
• /
• 2014

Laser heat source was applied on 3D poly urethane model built by 3D printer and cellulous acetate for joining. A diode laser with 808nm wavelength was transmitted through the 3D model and applied on the boundary of ABS/Acetate and 3D poly urethane model. Based on the experimental result, the ABS and 3D built poly-urethane polymers was successfully joined, but the mechanical strength was not enough at the joining boundaries in the range of 6watt to 8watt of laser heat source. However, biodegradable acetate was successfully joined without damaging the 3D built model and mechanical strength was properly achieved. The optimum laser power was found between 5watt and 8watt with scanning speed of 500mm/min, 700mm/min and 1,000mm/min. Based on the SEM analysis the filling mechanism was that the applied pressure on 3D built model squeezed the fluidic thermoplastics, ABS and acetate, into the structure of 3D model. Therefore soundness of joining was strongly depending on the viscosity of thermoplastics in polymers. The developed laser process is expected to increase productivity and minimize the cost for the final products.

• 한국자동차공학회논문집
• /
• 제25권2호
• /
• pp.190-200
• /
• 2017

In general, an assessment of the benefits and costs with regard to vehicle safety standards are validated before regulations are implemented. This paper performs this validation for the mandatory automobile safety devices requirement for new micro-mobility. The reviewed car safety standards involved the installation of seat belts, airbags, ABS, crash speed standards, and pedestrian warning system. The benefit was estimated as the cost of accident reduction due to the installation of vehicle safety standards. As a result, the safety belt showed a B / C of 4.0 or higher, and it was found that the seat belt should be installed from 2017. After the seatbelt regulation in 2017, the results of the scenarios with the airbag, ABS, crash speed of 40 km/h, and the pedestrian warning system showed B / C of 1.0 or more according to the year of regulation. This study can be useful as a tool in the decision-making process with regard to the timing and type of vehicle safety standards requirement of micro-mobility in the future.

• 한국농공학회논문집
• /
• 제46권5호
• /
• pp.131-139
• /
• 2004

In this study, on-site sewage treatment tests were conducted using the Absorbent Biofilter System (ABS) under different hydraulic loading rates to examine its treatment characteristics and efficiencies and to determine its feasibility as a small on-site sewage treatment system in a rural area. Results showed that the removal rates of BOD and SS were satisfactory at hydraulic loading rates of 100~150 cm/day, meeting the Korean effluent water quality standards for the riparian zone (10 mg/L). In the case of nutrients (N, P), however, the system did not perform well, necessitating further improvement for nutrient removal. A comparative analysis indicated that as a small on-site sewage treatment system, the ABS would be more suitable than other treatment systems in terms of performance stability, maintenance requirement, and cost-effectiveness and could be applied as an alternative treatment system in Korean rural areas.

• 동력기계공학회지
• /
• 제10권2호
• /
• pp.62-67
• /
• 2006

The maintenance of continuity on food processing has created a need for the rapid reinstatement of many types of frozen fish to an ambient temperature and good condition. A number of thawing methods are in current use have also several disadvantages in thawing time. discoloration mass loss caused by drying, capital and running cost. These damages are, it is claimed, either eliminated or improves by the vacuum system. An experimental study on the thawing for hair tail and Yellow croaker by the vacuum system were carried out. The Yellow croaker thawing time with this vacuum system took out 170 minutes to reach from $-10.3^{\circ}C\;to\;-0.8^{\circ}C$ at 20mmHg abs. and hair tail thawing time 220 minutes to reach from $-12.2^{\circ}C\;to\;0^{\circ}C$ at 20mmHg abs.

• 한국농공학회논문집
• /
• 제47권6호
• /
• pp.73-82
• /
• 2005

This study was performed to evaluate the need for heating wastewater to enhance treatment efficiency of organic matter (BOD, SS) during cold winter in newly developed Absorbent Biofilter System (ABS) which was established in the Suwon Campus of the Seoul National University. Treatments consisted of non-heating (2000 year) and heating(2001, 2002 year), and sampled data were analyzed during cold winter period as well as post winter period to investigate the influence of heating after winter season. Even the average air temperature showed only $0.4^{\circ}C$ difference between two experimental years, the difference in the average effluent temperature during cold winter period between heating and non-heating experiment was approximately $11^{\circ}C$. The average effluent concentration of organic matter in non-heating treatment exceeded the Korean standards for water quality of discharged effluent in riparian area (BOD and SS 10 mg/L); however, the standards were met in case of heating treatment during both winter and post winter period. Therefore, the need fur heating wastewater during cold winter season in ABS was justified. On the other hand, there was no improvement of treatment efficiency in T-N and T-p, but we observed the more activated nitrification as increasing the wastewater temperature. Because the average underground temperature was $5^{\circ}C$ higher than the average air temperature during cold winter period, we recommend that the ABS can be established in the underground rather than on-ground for saving the heating cost.

• 한국기계가공학회지
• /
• 제21권4호
• /
• pp.1-13
• /
• 2022

Household refrigerator cabinets must undergo cyclic testing at -20 ℃ and 65 ℃ for quality control (QC) after their production is complete. These cabinets were assembled from different materials, including acrylonitrile butadiene styrene (ABS), polyurethane (PU) foam, and steel plates. However, different thermal expansion values could be observed owing to differences in the mechanical properties of the materials. In this study, a technique to predict delamination on a refrigerator wall caused by thermal deformation was developed. The mechanical properties of ABS and PU foams were tested, theload factors causing delamination were analyzed, delamination was observed using a high-speed camera, and comparison and verification in terms of stress and strain were performed using a finite element model (FEM). The results indicated that the delamination phenomenon of a refrigerator wall can be defined in two cases. A method for predicting and evaluating delamination was established and applied in an actual refrigerator. To determine the effect of temperature changes on the refrigerator, strain measurements were performed at the weak point and the stress was calculated. The results showed that the proposed FEM prediction technique can be used as a basis for virtual testing to replace future QC testing, thus saving time and cost.

• Pediatric Infection and Vaccine
• /
• 제30권1호
• /
• pp.1-11
• /
• 2023

Respiratory syncytial virus (RSV)는 전 세계적으로 영유아에게 질병 부담과 사회적 비용이 매우 높은 병원체이지만 그 백신 개발은 상당히 지연되고 있다. 현재로선 단기-지속형 단클론항체인 palivizumab이 유일한 예방법이다. 그러나 최근 RSV 감염의 병태생리학에 대한 이해, 유전학의 발전, 모체 예방접종의 성공적인 시행 등으로 RSV 예방을 위한 단일클론 항체 및 백신의 개발이 급속히 추진되고 있다. 현재 2개의 장기-지속형 단클론항체 제제(nirsevimab 및 clesrovimab)와 2개의 모체 RSV pre-F 백신이 임상 3상 시험을 진행 중이거나 막 완료하였으며, 지금까지의 결과는 효과와 안전성 측면에서 매우 긍정적이다. 가까운 장래에 장기-지속형 단클론항체와 모체 예방접종을 통해 고위험군은 물론이고 기저질환이 없는 신생아 및 영유아들을 RSV로부터 효과적으로 보호할 수 있을 것으로 기대한다. RSV 예방의 새로운 시대에 빠르고 적절히 대비하기 위해서는 이러한 새로운 전략들에 익숙해지고 국내 RSV에 대한 역학 자료들을 계속 수집해 나갈 필요가 있다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제27권2호
• /
• pp.280-288
• /
• 2003

We need refrigeration system which can maintain the freshness of agricultural products, because of being distance from a tiller to a consumer. Vacuum Pre-cooling system has an advantage in quality maintenance through vapid cooling down by using latent heat of evaporation of stored products. A number or thawing methods in current use have also several disadvantages in thawing time. discoloration mass loss caused by drying, capital costs and running cost. These damages are, it is claimed, either eliminated or improved by the vacuum thawing system. An experimental study on the pre-cooling for the bean sprouts and cabbage, and thawing for hairtail and croaker by the low temperature vacuum system were carried out. The cabbage cooling time with this Pre-cooling vacuum system took about 60 minutes to reach from $23.2^{circ}C to 4.5^{\circ}C$ at 5 mmHg abs. ($6.66\times10^{-4}$ MPa). The croaker thawing time with this low temperature vacuum thawing system took about 170 minutes to reach from $-10.3^{circ}C to -0.8^{\circ}C$ at 20 mmHg abs ($2.67\tiems10^{-3}$MPa). The vacuum Pre-cooling and thawing system have merits compared with present systems in their short intervals to cool down and to thaw without any quality losses.

• 한국산업융합학회 논문집
• /
• 제23권6_1호
• /
• pp.907-915
• /
• 2020

Specification selection, Layout, specifications and combinations of Power Drives, and Ship motions were studied for FGPP(Floating Gas-fired Power Plants), which are still needed in areas such as the Caribbean, Latin America, and Southeast Asia where electricity is not sufficiently supplied. From this study, the optimal equipment layout in ships was derived. In addition, the difference between engine and turbine was verified through LCOE(Levelized Cost of Energy) comparison according to the type and combination of Power Drives. Analysis of Hs(Significant Height of wave) and Tp(spectrum Peak Period of wave) for places where this FGPP will be tested or applied enables design according to wave characteristics in Brazil and Indonesia. Normalized Sloshing Pressures of FGPP and LNG Carrier are verified using a sloshing analysis program, which is CFD(Computational Fluid Dynamics) software developed by ABS(American Bureau of Shipping). Power Transmission System is studied with Double bus with one Circuit Breaker Topology. A nd the CFD analysis allowed us to calculate linear roll damping coefficients for more accurate full load conditions and ballast conditions. Through RAO(Response Amplitude Operator) analysis, we secured data that could minimize the movement of ships according to the direction of waves and ship placement by identifying the characteristics of large movements in the beam sea conditions. The FGPP has been granted an AIP(Approval in Principle) from a classification society, the ABS.