• Journal of Ocean Engineering and Technology
• /
• v.29 no.1
• /
• pp.85-93
• /
• 2015

In this study, tensile tests were performed on aluminum alloys (AA6061 and AA6082) to investigate their mechanical behaviors at cryogenic temperatures. The temperature was varied from 110 K up to 293 K, and quasi-static strain rates of 10⁻⁴ s⁻¹ −10⁻² s⁻¹ were taken into account for the tests. The experimental results were analyzed to find the dependence on the temperature, strain rate, and fractured surfaces. As a result, it was found that the strength and elongation of the aluminum alloys were improved when the temperature was decreased. In addition, it was confirmed that the mechanical behaviors of the aluminum alloys were not dependant on the strain rate. Under a tensile load, two types of fractures were seen in the aluminum alloys: cup-cone (AA6061) and shear (AA6082).

• Journal of the Korean institute of surface engineering
• /
• v.55 no.1
• /
• pp.9-17
• /
• 2022

This work is concerned with the formation behavior of PEO (Plasma Electrolytic Oxidation) films on Al6082 alloy under the application of direct current (DC) and alternating current (AC) in an alkaline solution. Arc initiation voltage became much lower by the application of AC than DC, and arc initiation time became shorter under DC than AC. The number of pores present in the PEO films was much larger than that on the surface, irrespective of DC and AC. It was also found that the number of pores in the PEO films formed under AC was more than that under DC and the size of pores is smaller under AC than DC. During the formation of PEO films, a lot of heat was generated and solution temperature increased more rapidly under DC than under AC which is attributed to high PEO film formation voltage under DC than AC.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.141-143
• /
• 2007

Increasing demand of using low weight materials in recent automotive trends has been the challenge to develop a sound welding of aluminum alloys. A heat treatable AA6082-T6 and a non-heat treatable AA5083-0 aluminum alloys were joined in this study. Investigations revealed that about 60 UTS will be reduced due to welding process. Fracture happened in the interface between fusion zone and base metal of top specimen where penetration is shallow. Therefore, lower welding torch angle produced the better strength which allows deeper penetration to the top specimen. PWHT at $560^{\circ}C$ for 2 hours can be used to return the original UTS of the specimens.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.247-250
• /
• 2005

The need for improved fuel efficiency, weight reduction has motivated the automotive industry to focus on aluminum alloys as a replacement for steel-based alloy. To cope with the needs for high structural rigidity with low weight, it is forecasted that substantial amount of cast components will be replaced by tubular parts which are mainly manufactured by the extruded aluminum tubes. The extrusion process is utilized to produce tubes and hollow sections. Because there is no weld seam, the circumferential mechanical properties may be uniform and advantageous for hydroforming. However the possibility of the occurrence of a surface defect is very high, especially due to the temperature increase from forming at high pressure when it comes out of the bearing and the roughness of the bearing, which cause the surface defects such as the dies line and pick-up. And when forming a extruded aluminum tube, the free surface of the tube becomes rough with increasing plastic strain. This is well known as orange peel phenomena and has a great effect not only on the surface quality of a product but also on the forming limit. In an attempt to increase the forming limit of the tubular specimen, in the present paper, surface asperities generated during the hydroforming process are polished to eliminate the weak positions of the tube which lead to a localized necking. It is shown that the forming limit of the tube can be considerably improved by simple method of polishing the surface roughness during hydroforming. And also the extent of the crack propagation caused by dies lines generated during the extrusion process is evaluated according to the deformed shape of the tube.

• Transactions of Materials Processing
• /
• v.32 no.4
• /
• pp.221-227
• /
• 2023

While tube bending is a conventional forming technique, it is still used to make curved products for load-bearing members or aesthetically pleasing parts in various manufacturing industries such as automotive, aerospace, and others. Whole or local deformation of the final product such as springback, distortion, or local buckling are of interest in metal forming or precision manufacturing. In this paper, the factors affecting the cross-sectional deformation are explored. A 5-axis stretch bending machine was used for two-dimensional bending with extruded AA6082-T4 rectangular tubes. Three different bending sequences were employed: stretch before bending, stretch after bending, simultaneous bending and stretch. Furthermore, by considering both the stretch and bending angle, cross-sectional deformation was also analyzed. It was observed that employing stretch bending techniques can effectively reduce cross-sectional deformation and contribute to overall quality enhancement. Through this study, it was revealed that these factors have an impact on the cross-sectional deformation of the tubes.