• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.227-228
• /
• 2006

In this paper, we introduce the design and fabrication of 60 GHz low noise amplifier MMIC for IEEE802.15.3c WPAN system. The 60 GHz LNA was designed using ETRI's $0.12{\mu}m$ PHEMT process. The PHEMT shows a peak transconductance ($G_{m,peak}$) of 500 mS/mm, a threshold voltage of -1.2 V, and a drain saturation current of 49 mA for 2 fingers and $100{\mu}m$ total gate width (2f100) at $V_{ds}$=2 V. The RF characteristics of the PHEMT show a cutoff frequency, $f_T$, of 97 GHz, and a maximum oscillation frequency, $f_{max}$, of 166 GHz. The performances of the fabricated 60 GHz LNA MMIC are operating frequency of $60.5{\sim}62.0\;GHz$, small signal gain ($S_{21}$) of $17.4{\sim}18.1\;dB$, gain flatness of 0.7 dB, an input reflection coefficient ($S_{11}$) of $-14{\sim}-3\;dB$, output reflection coefficient ($S_{22}$) of $-11{\sim}-5\;dB$ and noise figure (NF) of 4.5 dB at 60.75 GHz. The chip size of the amplifier MMIC was $3.8{\times}1.4\;mm^2$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.12
• /
• pp.2413-2418
• /
• 2007

IN wireless sensor networks (WSNs), one challenging issue is to In wireless sensor networks (WSNs), one challenging issue is to construct a virtual backbone in a distributed and localized way while considering energy limitation. Dominating set has been used extensively as core or virtual backbone in WSNs for the purposes like routing and message broadcast. To ensure network performance, a good dominating set construction protocols should be simple and avoid introducing extra message. In addition, the resulting dominating set should be small, connected, and take into account the energy level at each node. This paper studies efficient and simple virtual backbone construction protocol using defer time in IEEE 802.15.4- based WSNs (e.g. Zigbee). The efficiency of our proposed protocol is confirmed through simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.3
• /
• pp.277-283
• /
• 2016

In this paper, a system of self-interference signal cancelation for in-band full duplex has been implemented and tested in RF/analog region. The system performance has been evaluated with NI5791 platform and NI Flex RIO. Due to the low power level of the NI5791, the RF signal is amplified by SKYWORKS SE2565T power amplifier. A circulator is used to feed the antenna both the transmitter and receiver. The RF FIR filter is designed by twelve delay taps in two different groups, and the interval between each delay tap is designed to have 100 ps. The amplified signal is distributed to antenna and the FIR filter by use of a 10 dB directional coupler. The tap coefficients of the RF FIR filter are tuned to estimate the self-interference signal coming from antenna reflection and the leakage of the circulator, and the self-interference signal is subtracted. The system is test with 802.11a/g 20 MHz OFMD at 2.56 GHz, and the output power of the amplifier of 0 dBm. The self-interference signal is canceled out by 53 dB.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.309-317
• /
• 2011

This paper describes a baseband analog (BBA) chain for wireless local area network (WLAN) applications. For the given specifications of the receiver BBA chain, the optimum allocation of the gain and filter rejection of each block in a BBA chain is achieved to maximize the SFDR. The fully integrated BBA chain is fabricated in 0.13 ${\mu}m$ CMOS technology. An input-referred third-order intercept point (IIP3) of 22.9 dBm at a gain of 0.5 dB and an input-referred noise voltage (IRN) of 32.2 nV/${\surd}$Hz at a gain of 63.3 dB are obtained. By optimizing the allocation of the gain and filter rejection using the proposed design methodology, an excellent SFDR performance of 63.9 dB is achieved with a power consumption of 12 mW.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.408-415
• /
• 2006

This paper suggests an improved system-level model of RF power amplifiers(PAs) including memory effects, and validates the suggested model by analyzing the power spectral density of the output signal with a predistortion linearizer. The original three-box(Wiener-Hammerstein) model uses input and output filters to capture RF frequency response of PAs. The adjacent spectral regrowth that occurs in three-box model can be perfectly removed by Hammerstein structure predistorter. However, the predistorter based on Hammerstein structure achieves limited performance in real PA applications due to other memory effects except RF frequency response. The spectrum of the output signal can be predicted accurately using the suggested model that changes a memoryless block in a three-box model with a memory polynomial. The proposed model accurately predicts the output spectrum density of PA with Hammerstein structure predistorter with less than 2 dB errors over ${\pm}30$ MHz adjacent channel ranges for IEEE 802.11 g WLAN signal.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2010.11a
• /
• pp.863-866
• /
• 2010

무선 센서 네트워크의 규모가 커짐에 따라 대규모의 센서 네트워크의 활용에 대한 기대가 커지고 있다. 기존 IEEE 802.15.4 를 이용한 네트워크의 규모에 따른 한계를 극복하기 위해 듀얼 라디오 센서 네트워크에 대한 많은 연구가 진행되고 있다. 듀얼 라디오 센서 네트워크는 단일 라디오를 내장한 전통적인 센서 노드(싱글 라디오 노드)에 듀얼 라디오 인터페이스(IEEE 802.11g, IEEE 802.15.4)를 내장한 센서(듀얼 라디오 노드)를 포함하여 클러스터를 구성한다. 본 논문에서는 이러한 듀얼 라디오 환경에서 효과적으로 동작하는 라우팅 프로토콜을 제안한다. 듀얼 라디오 노드는 네트워크 상에서 클러스터 헤드 역할을 하고 상위 계층을 이루며, 일반 노드는 클러스터 멤버 역할을 하는 하위 계층을 이룬다. 본 논문에서는 각 계층의 네트워크가 나타내는 특징을 이동성이 적거나 높은 네트워크의 특징으로 대입하여, 상위 계층에는 Pro-Active 프로토콜, 하위 계층에는 Re-active 프로토콜이 효과적임을 설명한다. 이를 바탕으로 듀얼 라디오 센서 네트워크에 적합한 라우팅 프로토콜로써 Pro-Active 프로토콜을 대표하는 DSDV 와 Re-Active 프로토콜을 대표하는 AODV 를 조합한 하이브리드 라우팅 프로토콜을 제안한다. 제안한 프로토콜의 성능을 확인하기 위해 센서네트워크 테스트베드를 구성하여 라우팅 복구 시간과 패킷 전송 안정성에 대한 성능을 입증한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.7
• /
• pp.413-423
• /
• 2014

With the increasing demands on high data rate, there has been growing interests in multi-input multi-output (MIMO) technology based on spatial multiplexing (SM) since it can transmit independent information in each spatial stream. Recent standards such as 3GPP LTE-advanced and IEEE 802.11ac support up to eight spatial streams, and massive MIMO and mm-wave systems that are expected to be included in beyond 4G systems are considering employment of tens to hundreds of antennas. Since the complexity of the optimum maximum likelihood based detection method increases exponentially with the number of antennas, low-complexity SM MIMO detection becomes more critical as the number of antenna increases. In this paper, we first review the results on the detection schemes for SM MIMO systems. In addition, massive MIMO reception schemes based on simple linear filtering which does not require exponential increment of complexity will be explained, followed by brief description on receiver design for future high dimensional SM MIMO systems.

• Journal of Communications and Networks
• /
• v.4 no.3
• /
• pp.161-169
• /
• 2002

Ad hoc wireless networks involving large populations of scattered communication nodes will play a key role in the development of low power, high capacity, interactive, multimedia communication networks. Such networks must support arbitrary network connections and provide coverage anywhere and anytime. This paper partitions such arbitrarily connected network architectures into three distinct groups, identifies the associated dual network architectures and counts the number of network architectures assuming there exist N network nodes. Connectivity between network nodes is characterized as a random event. Defining the link availability P as the probability that two arbitrary network nodes in an ad hoc network are directly connected, the network connection probability $ \integral_n$(p) that any two network nodes will be directly or indirectly connected is derived. The network connection probability $ \integral_n$(p) is evaluated and graphically demonstrated as a function of p and N. It is shown that ad hoc wireless networks containing a large number of network nodes possesses the same network connectivity performance as does a fixed network, i.e., for p>0, $lim_{N\to\infty} Integral_n(p)$ = 1. Furthermore, by cooperating with fixed networks, the ad hoc network connection probability is used to derive the global network connection probability for hybrid networks. These probabilities serve to characterize network connectivity performance for users of wireless ad hoc and hybrid networks, e.g., IEEE 802.11, IEEE 802.15, IEEE 1394-95, ETSI BRAN HIPERLAN, Bluetooth, wireless ATM and the world wide web (WWW).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.11
• /
• pp.1-8
• /
• 2011

In this paper, we study receiver design issue to apply the OFDM based WLAN specification, such as 802.11p, to the communications in high speed mobile environment, e.g., for the ICT based railroad control on a train having its speed up to 300 km/hr. To successfully apply the existing WLAN specifications without modifying its transmission format, the performance at the receiver will solely depends on the channel estimation performance if we ignore the affect of frequency offset With a speed of multiple hundred km/hr, the channel estimation using only the preamble will not provide enough precision since the channel changes so fast. Therefore, in this paper, taking the high mobility into account, we focus on the design of decision directed channel estimation and equalization techniques and perform simulations to evaluate and compare their performances and to finally confirm the applicability of the existing WLAN specification to the systems with very high mobility.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.257-264
• /
• 2007

In this paper, we have designed and fabricated a wide-band and high gain antenna which can integrate a standard of IEEE 802.1la$(5.15\sim5.25\;GHz,\;5.25\sim5.35\;GHz,\;5.725\sim5.825\;GHz)$. We inserted a parallel dual slot into a rectangular patch to have wide-band, and we offset an element of capacitance from the slot by using coaxial probe feeding method. We also designed a converter of $\lambda_g/4$ impedance with taper type line so that wide-band impedance can be matched easily. We finally designed structure with $2\times2$ array in order to improve the antenna gain, and the final fabricated antenna could have a good return loss(Return loss$\leq$-10 dB) and a high gain(over 13 dBi) at the range of $5.01\sim5.95\;GHz(B/W\doteqdot940\;MHz)$.