• 대한기계학회논문집A
• /
• 제37권6호
• /
• pp.775-782
• /
• 2013

본 연구에서는 마찰교반용접재의 피로균열전파 거동의 공간적 불규칙성을 고찰하기 위한 연구의 일환으로써, 최적의 조건에서 마찰교반용접된 7075-T651 알루미늄 합금 용접부의 LT-방향의 각각 5개의 피로균열전파 시험편에 대하여 일정 응력확대계수범위 제어하의 피로균열전파 실험을 수행하여 마찰교반용접부의 교반용접부재(WM)와 열영향부재(HAZ) 그리고 모재(BM)에 대한 피로균열전파 거동을 실험적으로 고찰하였다. WM재의 피로균열전파율이 가장 빠르게 나타났으며, 그 다음 HAZ재와 WM재 순으로 나타났다. 게다가 시험편간 피로균열전파율의 변동성은 WM시험편에서 가장 높았고, 반면 BM재에서 가장 낮게 나타났다.

• 동력기계공학회지
• /
• 제18권2호
• /
• pp.62-69
• /
• 2014

In this paper, in order to investigate the effects of marco and microscopic observations of fatigue crack growth in friction stir welded (FSWed) 7075-T651 aluminum alloy plates, fatigue crack growth tests were performed under constant amplitude loading condition at room temperature with three different pre-cack locations, namely base metal (BM-CL) and two kinds of pre-crack locations in welded joints, weld metal (WM-CL) and heat affected zone (HAZ-CL) specimens. The fatigue crack growth behavior of FSWed 7075-T651 aluminum alloy plates were discussed based on the marco and microscopic fractographic observations. The marcoscopic aspects of surface crack growth path for BM-CL and HAZ-CL specimens indicate relatively straight lines, however, the crack growth paths of WM-CL specimens grow first straight and by followed toward the TMAZ and HAZ. The microscopic aspects of fatigue fracture for BM-CL and HAZ-CL specimens indicate typical fatigue striation, but WM-CL showed intergranular fracture pattern by micro structural changes of FSW process.

• 대한기계학회논문집A
• /
• 제37권9호
• /
• pp.1109-1116
• /
• 2013

본 연구의 목적은 마찰교반용접된 7075-T651 알루미늄 합금 용접부에 대한 피로균열전파율의 공간적 불규칙성을 고찰하기 위한 것이다. 본 연구에서는 이전의 피로균열전파 실험 데이터를 활용하였다. 피로균열전파율의 공간적 불규칙성을 명확히 이해하기 위하여, 피로균열전파 실험은 일정 응력확대 계수범위 제어하에서 수행되었다. 재질, 즉 마찰교반용접된 7075-T651 알루미늄 합금 용접부의 용접재와 모재에 대하여 피로균열전파율의 공간적 불규칙성을 조사하기 위하여 실험 데이터가 해석되었다. 결론적으로 용접재의 변동성이 모재의 변동성보다 높게 나타났으며, Weibull 통계 해석에 의하여 변동성을 평가할 수 있음을 알았다.

• 동력기계공학회지
• /
• 제15권2호
• /
• pp.61-68
• /
• 2011

This paper investigates the tensile properties of the friction stir welded joints of Al 7075-T651 aluminum plate according to the welding conditions. A 7075-T651 aluminum alloy plate with a thickness of 6.0 mm was used in this investigation. For the friction stir welding (FSW) process, a tool with shoulder diameter of 20 mm and probe diameter of 9 mm was used. The rotation speed and traverse speed conditions were changed in this study, the other welding conditions are constant. The welding direction was aligned with the material rolling direction, and dimension of the FSW plate were $250{\times}100{\times}6\;mm$. As far as this work is concerned, the optimal FSW conditions are determined as the rotation speed, 600 rpm and traverse speed 0.8 mm/sec or the rotation speed, 800 rpm and traverse speed 0.5 mm/sec.

• 대한기계학회논문집
• /
• 제10권1호
• /
• pp.62-69
• /
• 1986

본 연구에서는 표면균열의 전파거동에 관한 연구의 일환으로 경량화재료 로서 항공기 구조용으로 널리 사용되고 있는 7075-T651 알루미늄합금을 준비하고 제하탄성 compliance법을 이용하여 표면 및 깊이 방향의 균열진전거동의 특성을 밝히고져 한다.

• 한국안전학회지
• /
• 제13권4호
• /
• pp.113-120
• /
• 1998

Fatigue crack growth rates(i.e. crack initiation and crack growth of short and long crack) are investigated using commercial plates of high strength Al alloy 7075-T651 for the transverse-longitudinal(T-L) direction in air, water and sea water. Also, the evaluation direct current potential drop(D.C.P.D) method and the fractographical analysis by SEM are carried out. Near threshold region, short crack growth rates were much faster than those of comparable long cracks, and these short crack growth rates actually decrease with increasing crack growth and eventually merge with long crack data. Fatigue crack propagation rates in aggressive media(i.e. sea water) increase noticeably over three times those in air. One of the most significant characters in this phenomenon as a corrosion-fatigue causes an acceleration in crack growth rates. Sea water environment, particularly Cl$^{[-10]}$ solution brings the most detrimental effects to aluminum alloy. The result of fractographical morphology in air, water and sea water by SEM shows obvious dimpled rupture and typical striation in air, but transgranular fracture surface in water and sea water.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.834-842
• /
• 1998

This paper examines the crack growth behavior of 7075-T651 and 5052-H32 aluminum alloy under high-low block loading condition. The cantilever beam type specimen with a chevron notch is used in this study. The crack growth and closure ae investigated by compliance method. The applied stress ratios are R=0.15, 0.0, -0.15 and R=-0.15, 0.0, 0.15. The crack growth rate was found to increase as the load amplitude increases. However,${\bigtriangleup}K_eff$ was almost independent on the stress ratio. The experimental constants of 7075-T651 and 5052-H32 in Paris law were c`=1-1.3${\times}{10^-7},m`=3~3.2 and c`=4~6{\times}{10^-9}, m`=4.3-4.8$, respectively. $K_op$ of 7075-T651 and 5052-H32 becomes smaller as the stress ratio decreases. It seems that the crack closure affects $K_op$.

• 동력기계공학회지
• /
• 제18권1호
• /
• pp.91-98
• /
• 2014

In this investigation, the effect of crack orientation on spatial randomness of fatigue crack growth rate (FCGR) in friction stir welded (FSWed) 7075-T651 aluminum alloy joints has been statistically analyzed by Weibull distribution. The fatigue crack growth tests are conducted under three different constant stress intensity factor range (SIFR) control at room temperature with R = 0.1 and frequency 10Hz on compact tension (CT) specimen machined at base metal (BM) and weld metal (WM). The experimental fatigue crack growth rate data were obtained for two types of specimens having LT and TL orientations. LT specimens both base metal and weld metal showed higher fatigue crack growth rate as compared to TL specimens. In the lower SIFR region, FCGR were found to be almost 3 times higher in higher SIFR region. The shape parameter of Weibull both LT and TL orientation for FCGR was increased with increasing SIFR, the scale parameter was also increased with increasing SIFR. The smallest value of the shape parameter was shown in weld metal specimens having LT orientation at lower SIFR region.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 전기학술대회논문집
• /
• pp.331-338
• /
• 2005

The grain structure, dislocation density and second phase particles in various regions including the stir zone(SZ), thermo-mechanically affected zone(TMAZ), and heat affected zone(HAZ) of a friction stir weld 6.35mm thick aluminum 7075-T651 alloy were investigated and compared with the base metal. The microstruectures of nugget zone were compared according to tool rotation speeds and tool transition speeds. The hardness profiles of nugget zone were increased, while decreasing rotation speed and increasing welding speed. The optimal microstructure was gained at the low rotation speed 800rpm and th high welding speed 124mm/min. The nugget microstructures of fracture surface, transgranular dimple and quasicleavage type were showed different fracture type with the HAZ, shear fracture type.

• 한국생산제조학회지
• /
• 제25권3호
• /
• pp.211-216
• /
• 2016

Al alloys are useful materials having high specific strength and are used in machining of parts having thin-walled structures for weight reduction in aircraft, automobiles, and portable devices. In machining of thin-walled structures, it is difficult to maintain dimensional accuracy because machining deformation occurs because of cutting forces and heat in the cutting zone. Thus, cutting conditions and methods need to be investigated and cutting signals need to be analyzed to diagnose and minimize machining deformation and thereby enhance machining quality. In this study, an investigation on cutting conditions to minimize machining deformation and an analysis on characteristics of cutting signals when machining deformation occurs are conducted. Cutting signals for the process are acquired by using an accelerometer and acoustic emission (AE) sensor. Signal characteristics according to the cutting conditions and the relation between machining deformation and cutting signals are analyzed.