• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.458-458
• /
• 2013

We investigated a study on the thermal degradation of boron doped zinc-oxide (BZO) layer which used as a transparent conducting layer on the Cu (In1-xGax) Se2 (CIGS) based thin film solar cells. Devices were annealed under the temperature of $100^{\circ}C$ or 100 hours and then Hall measurement was carried out to characterize the parameters of mobility (${\mu}Hall$), resistivity (${\rho}$), conductivity (${\sigma}$) and sheet resistance (Rsh). The initial values of ${\mu}Hall$, ${\rho}$, ${\sigma}$ and Rsh were $29.3cm^2$/$V{\cdot}s$, $2.1{\times}10^{-3}{\Omega}{\cdot}cm$, $476.4{\Omega}^{-1}{\cdot}cm^{-1}$ and $19.1{\Omega}$/${\Box}$ respectively. After the annealing process, the values were $4.5cm^2$/$V{\cdot}s$, $12.8{\times}10^{-3}{\Omega}{\cdot}cm$, $77.9{\Omega}^{-1}{\cdot}cm^{-1}$ and $116.6{\Omega}$/${\Box}$ respectively. We observed that ${\mu}Hall$ and ${\sigma}$ were decreased, and ${\rho}$ and Rsh were increased. In this study, BZO layer plays an important role of conducting path for electrons generated by incident light onthe CIGS absorption layer. Therefore, the degradation of BZO layer characterized by the parameters of ${\mu}Hall$, ${\rho}$, ${\sigma}$ and Rsh, affect to the cell efficiency.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.12
• /
• pp.75-82
• /
• 2010

This paper presents a wideband ${\Delta}{\Sigma}$ fractional-N frequency synthesizer for a multi-band single chip CMOS RFIC transceivers. A wideband VCO utilizes a 6-bit switched capacitor array bank for 2340~3940 MHz frequency range. VCO frequency calibration circuit is designed for optimal capacitor bank code selection before phase locking process. It finishes the calibration process in $2{\mu}s$ over the whole frequency band. The LO generation block has selectable multiple division ratios of ${\div}2$, ${\div}16$, and ${\div}32$ to generate LO I/Q signals for T-DMB/DAB/FM Radio systems in L-Band (1173~1973 MHz), VHF-III (147~246 MHz), VFH-II (74~123 MHz), respectively. The measured integrated phase noise is quite low as it is lower than 0.8 degree RMS over the whole frequency band. Total locking time of the ${\Delta}{\Sigma}$ frequency synthesizer including VCO frequency calibration time is less than $50{\mu}s$. The wideband ${\Delta}{\Sigma}$ fractional-N frequency synthesizer is fabricated in $0.13{\mu}m$ CMOS technology, and it consumes 15.8 mA from 1.2 V DC supply.

• Nuclear Engineering and Technology
• /
• v.17 no.3
• /
• pp.211-215
• /
• 1985

The effects of temperature and strain rate on the I-SCC behaviors of Zircaloy-4 were investigated by constant load test at 30$0^{\circ}C$ and constant elongation rate test at 300, 350 and 40$0^{\circ}C$ in 3.34mg $I_2$/㎤. The results showed that I-SCC susceptibility increased as the strain rate decreased or the temperature increased. The empirical relation between the stress and the time to failure at 30$0^{\circ}C$ was given by 1/ $t_{f}$∝exp (0.3$\sigma$/$\sigma$$_{UTS}$-31.5) When the I-SCC susceptibility was expressed by the ratio of fracture energy in iodine atmosphere to that in the inert atmosphere, severe I-SCC susceptibility was found near 7.6$\times$10$^{-6}$ sec at 30$0^{\circ}C$ and the maximum point of I-SCC susceptibility tended to shift to the higher strain rate with increasing the temperature. The quasi-cleavage fracture was observed in I-SCC fracture surface. From these results, it was certain that the film repture step was involved as an important process in the I-SCC mechanism of Zircaloy-4.4.

• Journal of the Korean Chemical Society
• /
• v.57 no.3
• /
• pp.335-340
• /
• 2013

A chemical reaction of PBDEs was implemented using the polyethylene glycols (PEGs) and KOH, along with different reaction conditions such as temperatures and times. Removal efficiencies of PBDEs before and after chemical reaction were examined by difference of concentration. PBDEs was not removed at lower temperatures of 25 and $50^{\circ}C$. However, under the increased temperature, removal efficiency of PBDEs in ${\sigma}$-xylene was gradually increased, showing completely removal of PBDEs containing 5-6 bromines on biphenyl frame. When increasing the reaction conditions to 4 hours and $150^{\circ}C$, removal efficiency of PBDEs reached almost 100%. In studying the reaction of PEGs with PBDEs, it confirmed that the PBDEs led to less brominated by PEGs through a stepwise process with the successive elimination of bromines.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.6
• /
• pp.651-657
• /
• 2018

A novel PLL with a delta-sigma modulator and a spur reduction circuit is proposed. delta-sigma modulator makes the LF remove noise easily by moving the spur noise to a higher frequency band. Therefore, the magnitude of spur can be reduced the reasonable bandwidth. The spur reduction circuit reduces the spur size by reducing the LF voltage change generated during the period of reference signal. The spur reduction circuit is designed as simple as possible not to increase the size of PLL. The proposed PLL with the previous two techniques is designed with a supply voltage of 1.8V in a 0.18um CMOS process. Simulation results show an almost 20dB reduction in the magnitude of spur. The spur reduced PLL can be used in narrow bandwidth communication system.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.1
• /
• pp.22-31
• /
• 2008

The operating window method is a novel approach in quality improvement. But it has not received deserved attention in academic research. If a critical factor for competing failure modes can be identified, the probability of failure can be reduced by widening the operating window of this factor. Traditional SN ratio for the operating window advocated by Taguchi has a critical shortcoming, which has been derived under the assumption that failure rates are determined by the operating window factor only. A new metric for robustness is given for the operating window method, which has relaxed the restrictive assumption of Taguchi's SN ratio. And procedures for determining optimal conditions based on the new metric is presented. The effectiveness of the proposed approach over the traditional practice is tested with the aid of a wave soldering process.

• Proceedings of the Korean Society for Quality Management Conference
• /
• 2007.04a
• /
• pp.3-8
• /
• 2007

본 논문에서는 사무 간접부서의 효율성 문제를 해결하고자 한다. 먼저 도요다 경쟁력의 원천인 유연생산 시스템의 아이디어를 응용하고자 하였다. 도요타의 유연생산시스템을 살펴보고, 프로세스 분석을 위해서 SIPOC 분석 기법을 살펴보았다. 도요타의 유연생산 방식을 사무 부서에 적용을 시도하였다. 실제 현장에 적용하여 효과를 보았다. 본 개선 기법은 인적 물적 제약이 많은 중소기업 및 공공부문의 경영혁신 방안으로 효과가 있을 것으로 제안한다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.7
• /
• pp.39-46
• /
• 2016

This paper describes the third order feedforward delta-sigma modulator with inverter-based integrators and a 1.5bit comparator for the application of audio signal processing. The proposed 3rd-order delta-sigma modulator is multi-bit structure using 1.5 bit comparator instead of operational amplifier. This delta-sigma modulator has high SNR compared with single-bit 4th-order delta-sigma modulator in a low OSR. And it minimizes power consumes and simplified circuit structure using inverter-based integrator and using inverter-based integrator as analogue adder. The modulator was designed with 0.18um CMOS standard process and total chip area is $0.36mm^2$. The measured power cosumption is 28.8uW in a 0.8V analog supply and 66.6uW in a 1.8V digital supply. The measurement result shows that the peak SNDR of 80.7 dB, the ENOB of 13.1bit and the dynamic range of 86.1 dB with an input signal frequency of 2.5kHz, a sampling frequency of 2.56MHz and an oversampling rate of 64. The FOM (Walden) from the measurement result is 269 fJ/step, FOM (Schreier) was calculated as 169.3 dB.

• Journal of the Korean Chemical Society
• /
• v.33 no.3
• /
• pp.326-331
• /
• 1989

Superconducting fiber of high Tc $YBa_2Cu_3O_{7-{\sigma}}$ was successfully prepared by the sol-gel method. The stoichiometric mixture of Y, Ba and Cu nitrates was dissolved in water, to which citric acid solution was added. Then ammonium hydroxide was added to the mixture in order to increase the pH to a value between 5.8 and 6.2. The mixture was heated carefully to form a homogeneous colloid sol at 358 K. The solution was viscous enough to draw a long gel fiber, which was then heated at 1223K for 8 hrs. under oxygen partial pressure of $Po_2$ = 1 atm., cooled slowly and annealed at 723K for 13 hrs.. The reacted superconducting sample maintained a fiber form with some shrinkage of its volume. The superconducting transition temperatures (Tc, onset and Tc, offset) of $YBa_2Cu_3O_{7-{\sigma}}$ have been determined to be approximately 95K and 82K, respectively. The superconducting phase was also confirmed by Meissner effect at liquid nitrogen boiling temperature.

• Journal of the Korean Society of Systems Engineering
• /
• v.6 no.2
• /
• pp.47-57
• /
• 2010

Taylor and Ford in the 1910s led to the "scientific management" for the entire industry from the manufacturing spread of TQM Total Quality Management has been structured as a management efficiency, such as 6-Sigma techniques were developed. SW development also introduces the idea, such as CMMI and SPICE-based process management, management practices have evolved. However, in recent years to increase the knowledge of workers in the manufacturing process oriented management approach is under serious challenge. Business performance or productivity will be varied depending all motivation, human relationship, job involvement rather than simply putting a lot of time. Especially in the SW industry which is depending on human resource, Creativity should be limited in traditional management methods. Recently, Google and Apple, Cisco and global advanced companies adopt a human relationship management. Their productivity and creativity in product development has been successful by giving autonomy and motivation, enthusiasm and vision to tile employees. Human relationship management since the mid-1990s, appears as a new paradigm so called Agile process in the field of SW development. Agile processes emphasis on light, flexible and responding to changes immediately in the business environment step away from traditional management approach which is the heavy and complicated process. In this paper, agile project management concepts and practices which is applied to industry will be examined.