• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2015년도 추계학술대회
• /
• pp.65-67
• /
• 2015

본 논문에서는 소형 WLAN 안테나에 적용 가능한 안테나 설계를 설계하고 적용 가능성을 검토하였다. 제안된 안테나는 $45mm{\times}45mm$ 크기의 RF4 기판(비유전율 4.4, 두께 1.6 mm, 손실탄젠트 0.025) 위에 $29mm{\times}29mm$ 크기의 마이크로스트립 패치 안테나를 인쇄하여 MoM법으로 계산하였다. 광대역 특성을 얻기 위하여 기판 상부에 위치한 패치 안테나의 대각 모서리를 3.2mm 커팅 처리하고 급전부는 50ohm 임피던스 정합을 위해 안테나 중심축에서 수평 방향으로 5.1mm 위치로 결정하였다. 계산 결과로서 WLAN 사용대역 2.4-2.48GHz을 고려할 때 정재파비가 2 이하인 주파수 대역은 2.365-2.45GHz(85MHz, 3.53%)로 나타났다.

• 대한기계학회논문집A
• /
• 제39권2호
• /
• pp.157-162
• /
• 2015

대형 5축 문형공작기계는 Gantry가 bed를 따라 절삭, 급송 이송하면서 가공을 수행 한다. 가공을 수행하는 중에 발생하는 오차(Zig-Zag)원인으로써 1) 양쪽 X축 이송모터의 위치오차 제어차이 2) 양쪽 Column의 무게차이에 의해 발생하는 마찰력에 대한 오차 3) spindle 회전력에 따른 오차 3가지의 원인이 있다. 3가지 오차원인을 분석하여 문형공작기계성능을 향상시키기 위해 연구를 진행 하였다. 연구결과로는 첫 번째로 양쪽 Column이 동일한 무게를 갖는 Gantry 구조에서 한쪽 축의 무게를 변경함으로써 마찰력이 미치는 영향을 확인하였다. 두 번째로 우리는 스핀들 회전이 미치는 영향을 해석 및 실험하였다. 그리고 우리는 스핀들 회전이 Gantry이송에 미치는 영향을 확인하였다.

• 한국기계가공학회지
• /
• 제11권5호
• /
• pp.60-67
• /
• 2012

In the study, the effect grinding condition on the workpiece arithmetical average roughness(Ra) to 10 steps leading to cutting each section with the spindle rotational speed 8000rpm and feed rate 150mm/min of grinding in GC(green silicon carbide) grinding processing after heat treatment and non heat treatment of SCM415 material. Also the following conclusions were obtained analysis of stress distribution displacement and finite elements method(FEM) on assemble parts with 3+2 axis simultaneous control through grinding and gave a load 11kg on ATC arm both sides gave a load of 11kg. For the centerline average roughness(Ra) in the heat and non-heat treatment work pieces, which were appeared the most favorable in the fifth section were $0.511{\mu}m$ and $0.514{\mu}m$, that were shown in the near the straight line section was the smallest deformation of curve. In addition, the bad surface roughness appeared on the path is too long by changing angle, the more inclined depth of cut, because the chip discharging is not smoothly.

• 대한치과기공학회지
• /
• 제39권1호
• /
• pp.35-42
• /
• 2017

Purpose: The purpose of this paper was to evaluate the occurrence of errors regarding adaptation by conducting a three-dimensional assessment comparing the bridge type dental restoration after the cutting process, which has multiple abutments, with a single type dental restoration. Methods: By using ten identical files obtained by scanning the master model, thirty designs were created consisting of ten maxillary right first premolars and ten maxillary right first molars with single crown abutments, along with ten bridge designs with the identical abutment. A 5-axis milling machine was used to produce the design file. The produced denture prostheses were scanned using a silicone replica for a STL file. An evaluation was conducted using 3D analysis software on the master model and each of the thirty data files. Results: The RMS value of the pre-molar (14) was $38.4{\pm}4{\mu}m$ for single and $54.7{\pm}6{\mu}m$ for bridge abutment; therefore, a statistically significant difference was observed for single and bridge designs although both shared the same abutment form (P<.05). Also, the RMS value of the molar (16) was $47.6{\pm}2{\mu}m$ and $56.6{\pm}5{\mu}m$ for the single and bridge designs, respectively, thereby presenting a statistically significant difference (P<.05). Conclusion: As a result, dental prosthesis fabricated using the single method presented better internal adaptation outcomes.

• 대한지리학회지
• /
• 제42권3호
• /
• pp.388-404
• /
• 2007

강원도의 내린천, 연곡천, 골지천, 오십천을 대상으로 영동 및 영서 하천의 하안단구 발달 과정을 지구조적인 측면에서 분석하였다. 하안단구 분포 패턴과 하천 하각 속도를 분석, 검토한 결과, 4개 하천 중 오십천 상류의 하안단구 4면, 5면, 6면에서는 태백산맥을 축으로 한 지반 융기의 영향이 뚜렷이 확인되었다. 태백산맥 분수계가 융기축이라면 영서하천 상류부 폭 $30\sim40km$ 구간이 융기대에 해당된다. 융기대 내부에 위치하는 내린천의 중 상류와 골지천 유역 전체는 하천 전 구간에서 융기작용이 활발하여, 상 하류 간의 융기량에 따른 하상비고 차이는 나타나지 않는다. 하안단구 2면$\sim$1면 사이와 1면$\sim$현재까지의 하각 속도는 두 시기의 기후 조건 차이로, 각각 $0.13\sim0.22m/ka,\;0.17\sim0.27m/ka$로 다르게 나타났다. 하안단구 1면 형성 이후부터 현재까지 영서 하천에 비해 영동 하천의 하각 속도가 다소 높다. 이는 하천 대부분 구간이 융기대에 포함되는 영서 하천에 비하여, 영동 하천은 하구가 최종적인 침식기준면인 해수면이므로 하각작용이 보다 활발했기 때문이다.

• Design & Manufacturing
• /
• 제12권2호
• /
• pp.40-45
• /
• 2018

Recently, in construction equipment machinery production, development has focused on environmentally-friendly functions to improve existing production capacity. For excavators as well, emphasis has been placed on response to environmental regulations, miniaturization, and noise reduction, while technology is being developed considering cost reduction and safety.Accordingly, the front support, an inner reinforcement part of the excavator, as well as high-strength steel plates to improve safety and reduce weight, are being applied.However, in the case of high-strength materials, Springback occurs in the final formed part due to high residual stress during product forming. Derivation of a forming or product shaping process to reduce springback is needed. Accordingly, regarding the front support, an inner reinforcement part of the excavator, this study derived a method to improve springback and secure shape stiffness through analysis of the springback occurrence rate and springback causes through a forming analysis.As for the results of analyzing the springback occurrence rate of existing products through forming analysis, springback of -22.6 mm < z < 27.35 mm occurred on the z-axis, and it was confirmed that springback occurred due to the stiffness reinforcing bead of the upper and middle parts of the product.To control product residual stress and springback, we confirmed a tendency of springback reduction through local pre-cutting and stiffness reinforcement bead relocation.In the local pre-cutting model, springback was slightly reduced by 5.3% compared with the existing model, an insignificant reduction effect. In the stiffness reinforcement bead relocation model, when an X-shaped stiffness reinforcement bead was added to each corner portion of the product, springback was reduced by at least 80%.The X-shaped bead addition model was selected as the springback reduction model, and the level of stiffness compared to the existing model was confirmed through a structural analysis.The X-shaped bead additional model showed a stress springback of 90% and springback reduction of 7.4% compared with the existing model, indicating that springback and stiffness will be reinforced.

• Restorative Dentistry and Endodontics
• /
• 제24권3호
• /
• pp.465-472
• /
• 1999

The aim of this study was to determine the shear bond properties of four dentin bonding systems to internal cervical dentin, and to investigate the effect of the pretreatment for removing smear layer and position of dentin on shear bond strength of dentin bonding agents. The materials tested in this study were consisted of four commercially available dentin bonding systems[Allbond 2(AB), Clearfil Linerbond 2(CL), Optibond FL(OP), Scotchbond Multi-purpose(SB)], a restorative light-cured composite resin[Z100]J and a chelating agent[RC-prep(RC)]. Fifty-six freshly extracted human molars were used in this study. Dentin specimens were prepared by first cutting the root of the tooth 1mm below the cementoenamel junction with a diamond bur in a high speed handpiece under air-water coolant, and then removing occlusal part at pulp horn level by means of a second parallel section, The root canal areas were exposed by means of cutting the dent in specimens perpendicular to the root axis. Dentin specimens were randomly assigned to two groups(pretreated group, not-pretreated group) based on the pretreatment method of dentin surface. In pretreated group, RC was applied to dentin surface for 1minute and then rinsed with NaOCl. In not-pretreated group, dentin surface was rinsed with saline Each groups were subdevided into four groups according to dentin bonding systems. Four dentin bonding systems and a restorative resin were applied according to the directions of manufacturer. The dentin-resin specimens were embedded in a cold cure acrylic resin, and were cut with a low speed diamond saw to the dimension of $1{\times}1mm$. The cut specimens were divided into three groups according to the position of internal cervical dentin. The shear bond properties of dentin-resin specimens were measured with Universal testing machine (Zwick, 020, Germany) with the cross head speed of 0.5mm/min. From this experiment. the following results were obtained : 1. In case of shear bond strength, there was no significant difference among dentin bonding systems in not-pretreated groups, whereas in pretreated groups, the shear bond strengths of AB and of SB were statistically significantly higher than those of CL and of OP. 2. The shear bond strengths of AB and of SB in pretreated groups were significantly higher than those in not-pretreated groups. 3. The shear bond strengths of radicular layer of OP were higher than those of occlusal layer of OP in not-pretreated groups, and of AB in pretreated groups. The shear bond strengths of radicular layer of AB and of CL in not-pretreated groups were higher than those in pretreated group.

• 한국추진공학회지
• /
• 제5권2호
• /
• pp.51-58
• /
• 2001

본 연구에서는 이중동축노즐로부터 대기로 방출되는 초음속 자유제트유동을 실험하였다. 출구마하 수가 2.0이고 충돌각이 다른 축소확대노즐 및 출구마하수가 1.0이고 충돌각이 다른 축소노즐을 사용하고, 주제트 압력비와 보조제트 압력비를 각자 4.0∼10.0, 1.0∼4.0으로 변화시켜 가면서 자유제트 유동장 특성을 조사하였다. 본 연구의 결과로부터 보조제트 압력비가 동축자유제트유동 특성에 영향을 미치며, 주제트 및 보조제트 압력비가 증가할수록 동축제트의 초음속 길이도 증가한다는 것을 알았다.

• Journal of Mechanical Science and Technology
• /
• 제19권5호
• /
• pp.1158-1168
• /
• 2005

A shunt from the left ventricle to the left anterior descending artery is being developed for coronary artery occlusive disease, in which the shunt or conduit connects the the left ventricle (LV) with the diseased artery directly at a point distal to the obstruction. To aid in assessing and optimizing its benefit, a computational model of the cardiovascular system was developed and used to explore various design conditions. Computational fluid dynamic analysis for the shunt hemodynamics was also done using a commercial finite element package. Simulation results indicate that in complete left anterior descending artery (LAD) occlusion, flow can be returned to approximately 65% of normal, if the conduit resistance is equal for forward and reverse flow. The net coronary flow can increase to 80% when the backflow resistance is infinite. The increases in flow rate produced by asymmetric flow resistance are enhanced considerably for a partial LAD obstruction, since the primary effect of resistance asymmetry is to prevent leakage back into the ventricle during diastole. Increased arterial compliance has little effect on net flow with a symmetric shunt, but considerably augments it when the resistance is asymmetric. The computational results suggest that an LV-LAD conduit will be beneficial when the resistance due to artery stenosis exceeds 27 PRU, if the resistance is symmetric. Fluid dynamic simulations for the shunt flow show that a recirculating region generated near the junction of the coronary artery with the bypass shunt. The secondary flow is induced at the cutting plane perpendicular to the axis direction and it is in the attenuated of coronary artery.

• 구강회복응용과학지
• /
• 제38권3호
• /
• pp.127-137
• /
• 2022

지르코니아는 다양한 공정과정을 거쳐서 제작되며, 각각의 요소는 최종 보철물의 물성에 영향을 줄 수 있다. 특히 밀링과정과 소결과정이 모두 지르코니아 보철물의 최종 완성도(integrity)에 영향을 미칠 수 있다. 밀링머신은 대부분 초정밀 5축 가공방식을 채택하고 있으며 어떤 방식을 사용하고 밀링기구를 어떻게 관리하는가에 따라서도 결과가 달라진다. 밀링블록은 절삭의 효율성과 심미재현성에 따라 선택하는데 물성의 변화를 야기할 수 있음은 주의해야 한다. 소결방식은 입자성장과 광학적 특성에 영향을 미칠 수 있는데 속도를 조절하는 최근의 방식에 대해서는 추가적인 연구가 동반되어야 정확한 평가가 이루어질 수 있다. 소결온도 뿐 아니라 온도 유지시간도 최종결과물에 영향을 줄 수 있다.