• Journal of electromagnetic engineering and science
• /
• v.1 no.1
• /
• pp.73-77
• /
• 2001

We studied the fabrication of GaAs-based pseudomorphic high electron mobility transistors(PHEMT`s) for the purpose of millimeter- wave applications. To fabricate the high performance GaAs-based PHEMT`s, we performed the simulation to analyze the designed epitaxial-structures. Each unit processes, such as 0.1 m$\mu$$\Gamma$-gate lithography, silicon nitride passivation and air-bridge process were developed to achieve high performance device characteristics. The DC characteristics of the PHEMT`s were measured at a 70 $\mu$m unit gate width of 2 gate fingers, and showed a good pinch-off property ($V_p$= -1.75 V) and a drain-source saturation current density ($I_{dss}$) of 450 mA/mm. Maximum extrinsic transconductance $(g_m)$ was 363.6 mS/mm at $V_{gs}$ = -0.7 V, $V_{ds}$ = 1.5 V, and $I_{ds}$ =0.5 $I_{dss}$. The RF measurements were performed in the frequency range of 1.0~50 GHz. For this measurement, the drain and gate voltage were 1.5 V and -0.7 V, respectively. At 50 GHz, 9.2 dB of maximum stable gain (MSG) and 3.2 dB of $S_{21}$ gain were obtained, respectively. A current gain cut-off frequency $(f_T)$ of 106 GHz and a maximum frequency of oscillation $(f_{max})$ of 160 GHz were achieved from the fabricated PHEMT\\`s of 0.1 m$\mu$ gate length.h.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.34 no.2
• /
• pp.142-146
• /
• 1989

Anther and/or tissue culture of cross pollinated crops would be very important because it can result in the direct use of haploids or doubled haploids for developing superior hybrids or varieties. The objective of the study was to investigate the response frequencies in anther and/or tissue-cultured hybrids of corn. pearl millet and buckwheat to identify agronomically acceptable germplasm of the crops. 27 crosses of corn inbred lines were evaluated by plating their anthers on N6. MS and Yu-Pei media. Two genotypes of FR1l41/FR16 hybrid cultured on N6 medium and Fla 2BT73/S6013 hybrid cultured on N6 medium responded with one anther producing calli when plated after 5$^{\circ}C$ low temperature treatment for one week. Immature embryos of corn hybrid Suwon 19 responded producing calli that were regenerated to plants at a 8.6 percent success rate. Of the 20 corn hybrids. immature tessels of FR1l41/FR16. B68/A1l6N//KS15. KS16/KS17. GA209/DB578 and SDB126/GA209 crosses responded at a relatively higher success rate producing calli that were regenerated to plants. In tissue culture of elongating culms of pearl millet x Napier grass interspecific hybrid. 2.5-4.0mm long pieces of the culm were good for callus induction resulting in higher success rate. The epicotyl of buckwheat was very good for tissue culture. and the node produced the plants regenerated directly without callus induction on the B5 medium containing I ppm BA and 0.05 ppm IBA. There were great differences in response to anther and/or tissue culture of corn, pearl millet and buckwheat due to genotype x medium and environment interactions.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.2
• /
• pp.331-340
• /
• 2000

The existing two-phase biological fluidized bed has some problems such as limit of oxygen transfer and blockade of fluidized distributor. In this study, three-phase swirl flow biological fluidized bed has designed to solve the problems and to investigate its running characteristics. TOC of influent synthetic wastewater was approximately $70mg/{\ell}$. HRT of reactor was 1.6 hours. Mean particle size of sand, as packing media, was 0.397mm and packing volume was varied from $200m{\ell}/{\ell}$ to $600m{\ell}/{\ell}$ by stages in the bed. The amount of biomass and effluent water quality was throughly investigated in the bed. Showing experiment results from the above conditions, it was possible to solve the problems of existing fluidized bed and to keep DO of $3mg/{\ell}$ or more. And it was also TOC removal rate of 91 to 94 %, MLVSS of 2,360 to $3,860mg/{\ell}$, MLVSS per g-media of 8.4 to 17.3 mg/g, F/M ratio of 0.59 to $1.04kg-TOC/kg-MLVSS{\cdot}day$, biofilm thickness of $35{\sim}71{\mu}m$ and sludge productivity of 1.03 to $2.35kg-SS/m^3{\cdot}day$. Optimal conditions in this experimental were as follows.; those were biofilm thickness of approximately $54{\mu}m$. MLVSS per g-media of 13 mg and media packing volume of 350 to $400m{\ell}/{\ell}$ when F/M ratio was low, treatment efficiency was high and sludge productivity was low. Showing the media with optics microscope in this optimal condition, attached microbes such as Epistylis sp. were observed. From SEM photographs, it showed that Coccus adhere to and grow on the media surface.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.30 no.1
• /
• pp.102-109
• /
• 2003

The purpose of this study was to evaluate the linear polymerization shrinkage(%) and microhardness of composite resin(Z-100, 3M, USA) according to 2-step light curing method. Conventional light curing unit(Curing Light 2500, 3M USA) and 2-step light curing unit(Elipar Highlight, ESPE, Germany) were used as light source. The strain gauge method was used for determination of polymerization shrinkage(%). Samples were divided by 3 groups according to light curing methods (Group I : $450mW/cm^2$, 40sec, Group II : $650mW/cm^2$, 40sec, Group III : $150mW/cm^2$, 10sec & $650mW/cm^2$, 30sec). Preparations of acrylic molds were followed by filling and curing. Strain gauges attached to each sample were connected to a strainmeter. Measurements were recorded at each second for the total of 10 minutes including the periods of light application. And microhardness of each group after 24hours from light irradiation were measured. Obtained data were analyzed statistically using Ore-way ANOVA and/or Scheffe test. The results of the present study can be summarized as follows: 1. Composite resin in acrylic molds showed the initial expansion at the early phase of polymerization. This was followed by the contraction with the rapid increase in volume during the first 60 seconds and gradually diminished as curing process continued. 2. The lowest linear polymerization shrinkage(%) was found in group III followed by group I, II during the measuring periods. 3. Group III using 2-step curing method showed statistically significant reduction of linear polymerization shrinkage(%) compared with group I, II at 1 minute and 10 minutes from light irradiation(p<0.05). 4. The microhardness values of each group not revealed significant difference.

• Progress in Medical Physics
• /
• v.10 no.3
• /
• pp.133-140
• /
• 1999

In this paper, as a preliminary study for developing a full 3D electron dose calculation algorithm, We developed 2.5D electron dose calculation algorithm by extending 2D pencil-beam model to consider three dimensional geometry such as air-gap and obliquity appropriately. The dose calculation algorithm was implemented using the IDL5.2(Research Systems Inc., USA), For calculation of the Hogstrom's pencil-beam algorithm, the measured data of the central-axis depth-dose for 12 MeV(Siemens M6740) and the linear stopping power and the linear scattering power of water and air from ICRU report 35 was used. To evaluate the accuracy of the implemented program, we compared the calculated dose distribution with the film measurements in the three situations; the normal incident beam, the 45$^{\circ}$ oblique incident beam, and the beam incident on the pit-shaped phantom. As results, about 120 seconds had been required on the PC (Pentium III 450MHz) to calculate dose distribution of a single beam. It needs some optimizing methods to speed up the dose calculation. For the accuracy of dose calculation, in the case of the normal incident beam of the regular and irregular shaped field, at the rapid dose gradient region of penumbra, the errors were within $\pm$3 mm and the dose profiles were agreed within 5%. However, the discrepancy between the calculation and the measurement were about 10% for the oblique incident beam and the beam incident on the pit-shaped phantom. In conclusions, we expended 2D pencil-beam algorithm to take into account the three dimensional geometry of the patient. And also, as well as the dose calculation of irregular field, the irregular shaped body contour and the air-gap could be considered appropriately in the implemented program. In the near future, the more accurate algorithm will be implemented considering inhomogeneity correction using CT, and at that time, the program can be used as a tool for educational and research purpose. This study was supported by a grant (＃HMP-98-G-1-016) of the HAN(Highly Advanced National) Project, Ministry of Health & Welfare, R.O.K.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.12
• /
• pp.63-69
• /
• 1972

There was a concentrated heavy rain resulted in 450mm of precipitation from Aug. 18 and 19, 1972. Almost all the paddy grown in the main plain areas of KimPo, Bu Cheon and Pyong Taek(N. L. $37^{\circ}$00'98'$-37^{\circ}$30'56", Long. $126^{\circ}$45'99"$-127^{\circ}$55'92"E) have been damaged of submergency. The effects of the different degrees of submergency in different growth stages of paddy, on the yield of paddy, rates of fertilization, maturity and degree of heading have been observed, and may be summarized as follows. (1) When the paddy was damaged due to submergency at the heading stage, a) on the basis of normal paddy, the yield of paddy may be expected about 67,57,40,9 and 6% with the submerged periods of 0.5, 1. 0, 2.0, 3.0 and 4.0 days, respectively, and a significant-negative correlation was found between the periods of submergency and the yields. b) As in the yield of paddy, rapid decreases in the rates of fertilizations and maturities of paddy were found as the submerged periods are increased. When the submerged periods are 0.5, 1.0, 2.0, 3.0 and 4.0 days, the corresponding rates of fertilizations and maturities observed are 89 and 88,83 and 78,52 and 40,24 and 19, and 12 and 9%, respectively, showing significant negrative correlations. c) Considerable decreases of the degree of heading were found as the submerged periods are increased. resulted in a significant negative correlation at 1% level between the degree of heading and submerged periods. (2) When the paddy plants were under submergency just before heading, the damage was found to be less than that at heading stage. The yields were 86,82,60,36 and 10%, as compared with the normal yield, with 0.5, 1.0, 2.0, 3.0 and 4.0 days of the submerged periods. (3) When the paddy was under the submergency at the mid-stage of head sprouting, its damage was severer than that of just before heading stage. The yields of paddy under the different submerged periods, 0.5, 1.0, 2.0, 3.0 and 4.0 days, were 79, 64, 34 and 6%, respectively, of the normal yields. normal yields.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.6
• /
• pp.414-420
• /
• 2012

In an effort to commercialization of energy saving aeration apparatus, panel-type aeration membranes were prepared from polyurethane sheet of J company in Korea having tensile strength higher than $400kg_f/cm^2$ with thickness of 0.5mm. Micropores of 100 m size were made by poring technique utilizing needles. From lab-tests in 450 L water tank at temperature of $20^{\circ}C$, the performance of aeration panels at 40 L/min aeration rate showed 5 mg/L DO in less than 3 minutes approaching saturation point of 8 mg/L within 8 minutes. The results show very high efficiency with $K_{La(15)}$ ($16.34hr^{-1}$), Standard oxygen transfer efficiency (SOTE 54.7%) and Standard aeration efficienct (SAE 7.88 kg/kwh). Other pilot scale test in a $2m^3$ water tank with water temperature ($19^{\circ}C$) and aeration rate (30 L/min) showed DO exceeding 5 mg/L within 8 minutes along with $K_{La(15)}$ ($5.8hr^{-1}$), SOTE (42.1%) and SAE (6.41 kg/kwh). These efficiencies represent 2~2.5 times higher than conventional aeration devices. Especially, the achievement of higher Oxygen Transfer Rate indicate higher commercial viability. Conventional aeration devices when applied to clean water and wastewater frequently cause problems due to differences in actual Oxygen Transfer Rate. Our actual tests with $40^{\circ}C$ animal farm wastewater resulted very high efficiencies with Oxygen transfer efficiency ($OTE_f$ 22.1%) and $OTE_{pw40}$ (39.6%).

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.2
• /
• pp.67-74
• /
• 2014

Recently, the number of road construction is increasing by industrial development. According to this industrial tendency, the number of traffic accidents are consistently increasing due to increasing number of vehicle on the road. This is mainly because traffic accidents are occurred by various parameter such as negligence of driver, vehicle defects, state of unstable road, natural environment etc. Lane department of vehicles from guardrail is occurring frequently. This type of accident is caused by vehicle performance improvement and shape of vehicle, weak guardrail installation and maintenance. Guardrail has the purpose on prevention such as prevention of traffic accident and prevention of deviating out of road, minimizing damage of driver and vehicle by collision as well as entry into the road through guardrail. Stability evaluation test of guardrail verifies the behavior of guardrail through the crash of truck. At this time, the crash condition has 100 km/h of velocity and $15^{\circ}$ of impact angle. In the case of ground condition, filling slope condition has relatively high bearing capacity of infinite ground towards the test. Guardrail is generally installed on road of shoulder in fill slope in korea. It is possible for stability problem to deteriorate ground bearing capacity in Guardrail in fill slope. The existed study towards stability of guardrail has been carried out in the infinite ground. However, the study on the behavior of fill slope with guardrail is not performed by vehicle collision. Therefore, In this study, the numerical analysis using LS-DYNA was executed for verification on behavior of fill slope with guardrail through vehicle collision. This numerical analysis was carried out with change of embedded depth on installed guardrail post in shoulder of fill slope by vehicle collision and 8 tonf truck crash providing at NCAN (National Crash Analysis Center). As the result, displacement and stress on fill slope are decreased in accordance with the increase of embedded depth of guardrail post. Ground bearing capacity is deteriorated at depth of 450 mm form shoulder of road on fill slope.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.54 no.1
• /
• pp.124-133
• /
• 2009

Demand for the high quality barley with fibroid material and functional substances has been increasing in recent although the amount of barley consumption decreased drastically during the last two decades. But the limited information on quality of barley makes consumers hard when they purchase barley for their own consumption. Therefore, 51 brand barley, .i.e., 28 naked barley and 23 waxy barley from supermarkets and 10 polished barley from local markets were collected, and their external quality were analyzed to provide basic information on brand barley. Among 51 brand barley, 56% were 1kg package and 25% were 800 g package and there was no significant difference ($1{\pm}3.62\;g$) between printed and actual weighs. The weight of 1,000 grains of naked barley and waxy barley ranged $18.6{\sim}26.7\;g$ and $14.6{\sim}24.7\;g$, respectively. Thousand grain weight of 38% of naked barley ranged $20{\sim}22\;g$, while that of 43% of waxy barley ranged $18{\sim}20\;g$. The ratio of normal grains was 88% and 94% for naked barley and waxy barley, respectively, when separated with 1.7 mm sieve. Although 82% of brand barley products were free from foreign substances, in 18% of brand barley products, sands, pieces of cloth and wood, other kinds of grain and insect larvae were found, Average test weight of brand barleys was $843g{\cdot}L^{-1}$ with range of $805{\sim}917g{\cdot}L^{-1}$. Water content was less than 14% in 7.8% of barley products, while it was $14{\sim}15%$ in 62.7% of them. Average whiteness of brand barley was 31.06, while waxy barley had higher whiteness with 27.28 than naked barley with 34.16. Heated water uptake rate of milled naked barley and milled waxy barley were 215.4% and 231.7%, respectively, while expansion rate of milled naked barley and milled waxy barley were 379.7% and 401.6%, respectively. Barley from local markets were as good as brand barley products in 1,000 grain weight, ratio of normal grains, inclusion of foreign substances, test weight, water content, whiteness, water uptake rate, and expansion rate, but they showed higher ratio of foreign substances included.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.4 no.2
• /
• pp.207-212
• /
• 2001

Purpose: Mycoplasma pneumoniae infection is relatively common in childhood. Its extrapulmonary manifestations have been reported so much, but hepatitis associated with it has not been studied yet until now in Korea. Methods: We performed the prospective study of 19 cases that had AST and ALT>50 IU/L respectively without evidence of hepatitis A, B, C, cytomegalovirus, and Ebstein-Barr virus infections amongst 143 patients with M. pneumoniae pneumonia who were admitted to the Department of Pediatrics, Seoul Red Cross Hospital from Jan. 1999 to Dec. 2000. Results: 1) Hepatitis occurred in 13.3% of Mycoplasma pneumoniae infection, especially in fall and winter times. The average age was 4.86 years and male to female ratio was 2.2:1. 2) Vomiting was developed in 21.1%, diarrhea in 36.8%, and hepatomegaly in 21.1%, respectively. And leukocytosis was noted in 21.1%, eosinophilia in 15.4%, anemia in 10.5%, and thrombocytosis in 5.3%, respectively. The average level of C-reactive protein was $6.34{\pm}4.82$ mg/dl. 3) There was no hyperbilirubinemia, but hypoalbuminemia was detected in 42.1%. The average serum levels of AST and ALT were $214.05{\pm}183.22$ IU/L and $284.16{\pm}286.84$ IU/L, respectively. 4) Chest radiology showed lobar or lobular consolidation in 73.7%, bronchial infiltration in 26.3%, and pleural effusion in 31.6%. 5) The average length of hospitalization was 7.9 days, and the average length of normalization of serum transaminases was 8.8 days. All patients recovered within 2 weeks completely. Conclusion: The prognosis of M. pneumoniae hepatitis is good. However, its incidence is not so low that liver function should be considerately checked in case of M. pneumoniae infection.