• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.7-12
• /
• 2016

This paper proposes a metal contact RF MEMS switch which utilizes a see-saw mechanism to acquire a switching action. The switch was built on a quartz substrate and involves vertical deflection of the beam under an applied actuation voltage of 5.46 volts over a signal line. The see-saw mechanism relieves much of the operation voltage required to actuate the switch. The switch has a stiff beam eliminating any stray mechanical forces. The switch has an excellent isolation of −90.9 dB (compared to − 58 dB in conventional designs ), the insertion of −0.2 dB, and a wide bandwidth of 88 GHz (compared to 40 GHz in conventional design ) making the switch suitable for wide band applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.10
• /
• pp.1151-1156
• /
• 2012

In this paper, the baseband filter is proposed in order to maintain a constant sensitivity regardless of distances for 77 GHz automotive radar system. Using existing DCOC loop circuit can remove DC offset and also cancel differences of received power depending on the distance. Measured results show that the maximum gain is 51 dB and high pass cutoff frequency can be tuned from 5 kHz to 15 kHz. The slope of high pass filter can be tuned from -10 to -40 dB/decade for the distance compensation. The measured NF and IIP3 are 26 dB and +4.5 dBm with 4.3 mA at 1.0 V supply voltage, respectively. The fabricated die size $500{\mu}m{\times}1,050{\mu}m$ excluding the in/out pads.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.19 no.1
• /
• pp.19-24
• /
• 2024

In this paper, in order to realize lower cut-off frequency of the waveguide, the folded Ridge waveguide (FRWG) is suggested by alternating T-shape structure in the conventional folded waveguide with Y-shape structure. Suggested FRWG can be equivalent by the reverse Ridge waveguide. As the height of side of the FRWG is lower, the width of side is increased. Therefore, the cut-off frequency of the FRWG can be decreased more than half compared with conventional waveguide. The FRWG is designed with the length, height, and width of Y-shape structure of 40mm, 20mm, and 2mm, respectively. Designed FRWG has the cut-off frequency of the 1.996GHz. Also, the transition between the FRWG and SMA connector is designed. The transition is optimized by the capacitance of the signal line of the connector. Its result shows the VSWR under 2:1 in the band of 2.064 ~ 3.050 GHz. Suggested FRWG can be applied with miniaturization of various waveguide devices.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.371-374
• /
• 2005

This paper presents the design and fabrication of a cost effective and broad band 8$\times$8 stacked patch array antenna which are backed by a metal cavity operating at 400Hz based on 4 layers LTCC technology. Gain of antenna can be enhanced by using a metal cavity, which can be easily implemented by using LTCC substrates and vias. The broadband performance can be obtained by varying the dimension of patch and the number of layers. Furthermore, to keep the feeding network as smal1 as possible and reduce radiation from feeding network a mirrored patch orientation and embedded micro strip line are adopted, The fabricated antenna is $40\times45\times0.4$ $mm^3$in size. It shows gain 20.4dBi, beam width 10.7deg and impedance bandwidth of l0dE return loss 3.35GHz (40.9$\sim$44.25 GHz), which is about 8% of a center frequency.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.1
• /
• pp.72-75
• /
• 2016

In this paper, we proposes a internal antenna for wireless DVI dongle device using the folded monopole structure. The proposed antenna uses a basic structure of spiral and monopole. The antenna optimized for parameters length, gap, width, and rectangle of folded monopole antenna using the spiral structure. To confirm the characteristics of the antenna parameters, HFSS from ANSYS Inc. was used for the analysis. We used an FR4 dielectric substrate with a dielectric constant of 4.4. The DVI dongle size of the proposed antenna is $50{\times}40{\times}1.6mm$, and the size of the antenna area is $10{\times}40mm$. There is a value of return loss less then -10dB in 2.4GHz and 5.8GHz, band and the maximum antenna gain is -4.13dBi. The utilization possibility of the wireless DVI Dongle antenna have a folded monopole with spiral shape could be confirmed according to compare and analyze the simulation and measurement data.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.5
• /
• pp.7-14
• /
• 1977

Conventionally, a TIVT has been used for high power amplification in the microwave frequency range. However, an ultra-high-power amplifier in the 2GHz range has successfully been designed and fabricated employing high power transistors developed recently and available commercially. In the design of the amplifier, a balanced-pair configuration is adopted in order to obtain very high microwave power, and a good impedance matching is achieved by making use of microstripline techniques. For the RF power divider as well as combiner, an approach of stripline directional coupler isadopted because of its easiness in fabrication. The coupler so designed and fabricated indicates a satisfactory performance as a quadrature hybrie coupler. Measurements on the amplifier developed for an immediate commercial application also exhibit excellent overall performance characteristics RF power output, 14 watts, gain 14dB, frequency bandwidth, 160MHz, effciency 40%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.12 s.115
• /
• pp.1206-1211
• /
• 2006

In this paper, a Balun-BPF with the balun and BPF characteristics is proposed by using dual-mode ring resonator of $1{\lambda}$. We obtained the property of balun with the phase imbalance by symmetrically placing each output of ring resonator. The dual mode has been made by impedance difference between input and output lines. The fabricated Balun-BPF shows bandwidth of 40 MHz and insertion loss of 2.4 dB at a center frequency of 2.45 GHz. It shows the phase imbalance of $180{\sim}184$ degree and the magnitude imbalance of within 1 dB. The measured frequency responses agree well with simulated ones.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.5
• /
• pp.653-662
• /
• 1999

In this paper, subharmonically injection locked oscillator(SILO) was designed and measured. SILO with series feedback was designed using Two Signal Method(TSM). The free-running oscillator frequency was 9.4 GHz with 6 dBm output power. In case of injection, the multiplied injected signal locked the free-running frequency. The locked signal output power was higher than any other spurious response at least 40 dB. The locking range was 220MHz (second subharmonic locking), 100 MHz(4th subharmonic locking), and phase noise was -111 dBc/Hz, -104 dBc/Hz at 100kHz offset, respectively.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.3
• /
• pp.32-40
• /
• 1991

A modified transmission line model is proposed for input impedance analysis of a square microstip antenna with single-circularly-polarized. Alog-periodic arrangement with microstrip antenna (LPMA) which consists of 3 resonant element ($3\times1$) is designed for broadband operation ranging from 11.2 GHz to 12.4 GHz, based on this pro- posed model from transmission line model. Aplanar array ($3\times4$array), in which 4sets of the above LPMA are in the same plane, is fabricated for high gain X-band satellite communication antennas. The optimum spacing between each LPMA is determined using computer simulation for the minimum bariation of far field pattern and null. This $3\times4$array has a measured values of gain greater than 8dBi, VSWR les then 2.3, and bandwidth greater than 7% respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.128-136
• /
• 2006

In this paper, design and implement 50W Doherty power amplifiers for 3GPP repeater and base station transceiver system. Efficiency improvement and high power property of ideal Doherty power amplifier is distinguishable; however bias control for implementation of Doherty(GDCHD) amplifier is difficult. To solve the problem, therefore, GDCHD(Gate and Drain Control Hybrid Doherty) power amplifier is embodied to drain bias adjustment circuit to Doherty power amplifier with gate bias adjustment circuit. Experiment result shows that $2.11{\sim}2.17\;GHz$, 3GPP operating frequency band, with 57.03 dB gain, PEP output is 50.30 dBm, W-CDMA average power is 47.01 dBm, and -40.45 dBc ACLR characteristic in 5MHz offset frequency band. Each of the parameter satisfied amplifier specification which we want to design. Especially, GDCHD power amplifier shows proper efficiency performance improvement in uniformity ACLR than Doherty power amplifier.