• Geophysics and Geophysical Exploration
• /
• v.22 no.3
• /
• pp.99-106
• /
• 2019

Resistivity method has been used for the dam safety inspection and, for the convenience of fieldwork, two-dimensional (2D) resistivity data has been usually measured along the dam crest. However, since the dam has three-dimensional (3D) structure, 2D resistivity survey along the dam crest violates 2D assumption and 3D effects caused by 3D topography and material properties in the dam distort the inversion result of 2D resistivity data acquired along the dam crest. Furthermore, it is really hard to evaluate the 3D structure of the dam and 3D leakage pathway using 2D resistivity survey because 2D resistivity survey can provide only 2D resistivity section beneath the survey line. In this study, 3D resistivity survey was conducted at a dam in Korea. By comparing the results from 3D and 2D resistivity surveys, merit and demerits of 3D survey were investigated. Finally, it was confirmed that 3D survey can provide more accurate information about the dam status and 3D leakage pathway compared to the 2D survey. Therefore the 3D resistivity survey should be actively expanded for more accurate dam safety inspection even though more time and expense are required.

• Journal of the Korean earth science society
• /
• v.30 no.6
• /
• pp.699-708
• /
• 2009

Recently as the interest in the development of domestic ore deposits has increased, we can easily find some studies on exploration geophysics-based ore-deposit survey in literature. Based on the fact that mineralized zone are generally more conductive than surrounding media, electrical resistivity survey among several geophysical surveys has been applied to investigate metallic ore deposits. Most of them are grounded on 2-D survey. However, 2-D inversion may lead to some misinterpretation for 3-D geological structures. In this study, we investigate the feasibility of the 3-D electrical resistivity survey to 3-D vein-type ore deposits. We first simulate 2-D dipole-dipole survey data for survey lines normal to the strike and 3-D pole-pole survey data, and then perform 3-D inversion. For 3-D ore-body structures, we assume a width-varying dyke, a wedge-shaped, and a fault model. The 3-D inversion results are compared to 2-D inversion results. By comparing 3-D inversion results for 2-D dipole-dipole survey data to 3-D inversion results for 3-D pole-pole survey data, we could note that the 2-D dipole-dipole survey data yield better inversion results than the 3-D pole-pole data, which is due to the main characteristic of the pole-pole array. From these results, we are convinced that if we have certain information on the direction of the strike, it would be desirable to apply 2-D dipole-diple survey for the survey lines normal to the strike. However, in most cases, we do not have any information on the direction of the strike, because we already developed the ore deposit with the outcrops and the remaining ore deposits are buried under the surface. In that case, performing 3-D pole-pole electrical resistivity survey would be a reasonable choice to obtain more accurate interpretation on ore body structure in spite of low resolution of pole-pole array.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2000.09a
• /
• pp.41-53
• /
• 2000

Electrical resistivity survey is widely applied to the dam seepage problems. Main purpose of the resistivity survey is to delineate the inhomogeneity in the dam. In this study, two- (2-D) and three-dimensional (3-D) resistivity survey methodology and corresponding interpretations of the data have been analyzed using 3-D resistivity modeling results. Since resistivity structures beneath the dam and its shape are 3-D in nature, we could get more accurate image of the dam structures using 3-D survey compared to 2-D survey even though we cannot employ the grid-shape survey layout.

• Journal of the Korean Institute of Rural Architecture
• /
• v.21 no.4
• /
• pp.25-36
• /
• 2019

The purpose of the study is to analyze how to document survey and repair data on wooden architecture culture assets. Documentation was analyzed in comparison to digital developments from the past to the present. Although the accuracy of survey equipment has been improved by digital development, survey drawing has not changed. For example, a 3D Scanner, survey equipment, was introduced but is being used for conversion into 2D data. Data provided by the drawing included in the survey and repair reports were not accumulated. As it stands, it is inaccessible and disorganized. Data generated from the survey, repair, and maintenance has to be consistent. A BIM system was proposed to integrate information on wooden architecture cultural assets.

• Journal of KIBIM
• /
• v.10 no.3
• /
• pp.33-42
• /
• 2020

Recently, in the smart construction field, it is possible to construct spatial information of 3D data base quickly and accurately using drones, LiDARs and ARs,. Most public ordering institutions are pushing for the efficiency of construction work through establishing and announcing road maps and guidelines for utilizing BIM for the entire life cycle of construction. However, in most policies, the impact of 3D data on the entire life cycle is limited by only partially constructing and utilizing 3D data or by being mentioned. In addition, many public institutions, construction companies and planning companies did not actively utilize survey information during the actual construction phase, despite the possibility of using 3D survey information. In order to confirm the utilization of survey information, a total of eight private construction companies were selected and interviewed by experts. The analysis shows that most of companies lack the performance of drone measurements or have a lack of awareness of advantages, and among them, construction companies are relatively active. Based on these opinions, this study examined the usability of surveying information and examined measures to expand the utilization of survey information in legal and institutional aspects, technology development aspects and industrial development.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.5
• /
• pp.343-349
• /
• 2021

In The process from design to construction in the existing construction work was less efficient due to the contradictory approach of identifying the 3D state in the plan view and the repeated generation of surveys, floor plans, drawings. Accurate 3D design data is essential for smart construction. However, most of the existing related studies have focused on explaining the development method and main functions of equipment or improving the productivity of smart construction. Therefore, in this study, the utility of 3D design model generation for smart construction and construction survey using 3D laser scanner was evaluated. Plane and vertical road alignment were created using the specifications of the road. The generated road alignment was created as a three-dimensional corridor design using cross-sections at intervals of 20m. In addition, it was possible to create a DTM (Digital Terrain Model) using a digital map and effectively create a 3D design model for the study area through overlapping. Construction survey using a 3D laser scanner showed accuracy within 10cm as a result of the accuracy evaluation. These results proved that construction surveying using a 3D laser scanner is possible because it satisfies the acceptable accuracy of the relevant regulations modeling of target areas using 3D design and construction survey using 3D laser scanner can be a way to address shortcomings of existing GNSS (Global Navigation Satellite System) methods. And accurate 3D data will be used as essential data as basic data for smart construction.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.4
• /
• pp.361-369
• /
• 2018

The ship surveyor makes a scheme of reasonable ship operation by examining whether the ship has been properly constructed in accordance with the rule of classification societies and international conventions or whether the facilities of the ship in operation meet the standard stipulated by law. Even though the ship surveyors of classification society generally consist of people who have the skill of design or operation of a ship, it takes a long time to train a surveyor to the maturity level. This paper describes the development of survey simulator based on virtual ship environment that enables the surveyor minimize trial and errors to survey the ships. By using VR(Virtual Reality) based survey simulator, surveyors possibly achieve improvement of competence in survey quality by means of safe and immersive training environment. In order to improve the usability and utility of the VR simulator, the ship 3D model has been generated using 3D CAD model for design and production in shipyard. Through this, we suggested the possibility of consistent use of 3D model as the digital twin of a ship.

• Geophysics and Geophysical Exploration
• /
• v.18 no.1
• /
• pp.14-20
• /
• 2015

Three-dimensional (3D) resistivity method is an effective tool in the engineering site survey because it can provide a 3D resistivity distribution of the site. In this study, we tried to find out faults, fractures and coal seams that can cause the collapse of the tunnel. We carried out 2D resistivity survey along 5 parallel lines and 11 cross lines and merged all the apparent resistivity data for 3D inversion. Finally, from the 3D resistivity image and drilling data we presented the 3D distribution of faults, fractures and coal seams that are considered the main cause of the tunnel collapse.

• Geosciences Journal
• /
• v.22 no.6
• /
• pp.891-902
• /
• 2018

Techniques for more reliable detection of 3D subsurface flow paths are highly important for most water-related geotechnical projects. In this case study, a magnetometric resistivity method with a new approach and state-of-the-art technology ("Willowstick survey") was applied to the testbed dam (YD dam) site, and its applicability was validated by geotechnical investigation techniques including borehole drilling and sampling, Lugeon test, flow direction and velocity test, and seismic tomography. In addition to the magnetometric survey, a 3D electrical resistivity survey was performed independently and the results were compared and discussed. The electrical resistivity survey was effective in detecting groundwater levels, but it was limited in mapping leakage paths. On the other hand, the Willowstick magnetometric survey effectively detected geologic weaknesses (e.g., fault fracture) and potential leakage paths of the dam site foundation rocks. The results of this research are expected to be effective for water infrastructures where leakage is an important issue.

• Nutrition Research and Practice
• /
• v.14 no.6
• /
• pp.667-678
• /
• 2020

BACKGROUND/OBJECTIVES: This study aimed to improve portion size estimation aids (PSEAs) used in the nutrition survey of the Korea National Health and Nutrition Examination Survey (KNHANES) and validate the accuracy and precision of the newly developed aids. SUBJECTS/METHODS: We conducted intensive interviews with survey experts in KNHANES and consulted with experts to collect opinions about improvement of PSEAs. Based on the results of the interviews, 5 types of PSEAs (rice bowl, earthen pots, mounds, measuring spoons, and thickness sticks) were newly developed using 3-dimensional (3D) modeling or modification of color or shape. Validation tests were conducted with 96 adults 20 years old or older. For the rice bowl and earthen pots, the participants were asked to select the more similar PSEA in size after being shown the real dishes. For the mounds, measuring spoons, and thickness sticks, the participants were presented with actual plates of food and asked to estimate the given portion sizes using the given PSEAs. RESULTS: The improved 2-dimensional (2D) picture aid for the rice bowl reflecting the size distortion by angle of view using 3D modeling was perceived more closely to the actual size than the current 2D picture (P < 0.001). The change of the color of 2D pictures and 3D models, the change of shape of the measuring spoons, and the 3-dimensionalization of the 2D mounds had no significant improvement in the subjects' perception. CONCLUSIONS: The currently used 2D PSEAs need to be fully redesigned using 3D modeling to improve subjects' perception. However, change of color or shape will not be necessary. For amorphous foods, it is suggested that more evaluation be performed before reaching a final conclusion in the use of PSEAs, or alternative ways to improve accuracy of estimation need to be explored.