• Journal of Korean Medicine Rehabilitation
• /
• v.26 no.2
• /
• pp.123-132
• /
• 2016

Objectives The aim of this study done as pilot study is to analyze the current state of patients who have low back pain through registry. Methods This study is done under approval of Gil Oriental Medical Hospital of Gachon University, Oriental Medical Hospital of Sangji University, Jecheon Oriental Medical Hospital of Se-Myung University IRB. Among subjects who signed the consent form by their own will, we decided whom to register as subjects of this study by the standard of selection and exception. We collected the sociological investigation, character of low pack pain, degree of symptom which they felt before and after the hospitalization from registered subjects. Results 1. The number of the subjects is 16. The average age is 41.0. 9 of them are female, 7 of them are male. Most of the subjects have history illness which has connection with low pack pain. 2. According to the patient's free description of the back pain, 6 of them suffered throbbing pain. And 8 of the patients have chronic pain, 6 of them have intermittent pain of back pain analysing the character of the low back pain. They answered the pain lasted for 47.6 minutes on average. 3. About the change on the average R.O.M. of L-spine, R.O.M. of Lateral bending, Extension, Flexion, Rotation has increased after leaving the hospital compared with before hospitalization. 4. The amount of discomfort or strength of pain, which was checked by VAS on the day of leaving the hospital, has decreased than they were before the hospitalization. And there was the improvement on the dysfunction score and EQ-5D. Conclusions Through this study, we specifically analyzed the symptoms of the low back pain by accumulating the analysis about the symptoms using several indicators and description which is freely spoken by patients about their symptoms. Further research is expected to complete multi-center registry by building registry and by using it, to get various epidemiologic informations about low back pain.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.10 no.2
• /
• pp.84-96
• /
• 2007

The purpose of this study was to select herbaceous plants that can be used for presenting various views and biodiversity on the extensive rooftop greening. Experiment plots were constructed in July 2005 on the rooftop of the Administration Building in the Seoul Women's University. For this experiment, planters were used to design rooftop greening. The size of a planter is 500mm${\times}$500mm${\times}$100mm and each planter has the water storage plate in the lower part of it. The soil was constructed by mixing pearlite, vermiculite, cocopeat, and leaf mold in the ratio of 6 : 2 : 1 : 1. The plot was divided into the watered plot and the dry plot. Since each plot was constructed 2 times, finally 4 planters were constructed in total. One hundred species were used for the experiment and 9 plants per species were planted in each planter. Plants were organized according to types of plants and the experiment used 86 native herbaceous plants, 6 herbs, and 8 foreign plants. The plots were monitored once a month, from July to November 2005. The length and width of plants were tape-measured and covering rate was calculated by CAD program. "SPSS 10.1" was used for a statistical analysis. The result showed no significant difference between the watered plots and the dry plots. In cases of some plants, there were statistically significant differences between the watered planter and dry planter such as follows : Astilbe chinensis and Polygonatum odoratum which are shade plants were measured as the highest value on the watered pots, and Aquilegia buergeriana, Chrysanthemum zawadskii, Calendula arvensis and Gypsophila cerastioides D.Don which are sunny plants were measured as the highest value on the dry plots. According to the final analysis of the data collected and observed for growth condition during the first year of the research, 51 species including Prunella vulgaris var. lilacina and Veronica linaiaefolia in native herbaceous plant, 5 species with Lavandula angustifolia in herbs, and 3 species with Lantana camara and Muscari armeniacum in foreign plants showed the highest growth condition. In conclusion, it is suggested that various plants including sedums could be effectively used for extensive rooftop greening to improve landscape(a view) of the rooftop and increase ecological values.

• The Journal of Natural Sciences
• /
• v.5 no.1
• /
• pp.67-75
• /
• 1992

In the our country, especially in Yeongil and Wolsung area, abundant authigenic zeolites are found from the tuffaceous sediments and volcanic rocks of Miocene age showing wide variation in their mineralogy and abundance from horizon to horizon. The principal zeolite species identified are clinopti-lolite. mordenite. heulandite. ferrierite, and erionite. etc. Zeolite minerals are widely used in many countries in the following applications; (a) in air separation adsorption processes; (b)as desiccants; (c)in inorganic building materials; (d)in papermaking; (e)in fertilizers; (f)as soilconditioners-this application is based upon the ability of the zeolite to ion exchange with soil nutrients; (g)in the treatment of radioactive wastes; and (h)as adsorbents for toxic gases, etc. In the present paper, using natural zeolite mordenite treated with IN hydrochloric acid or IN sodium chloride solution as column packings, separation characteristics of argon, nitrogen, carbon monoxide, and methane gases have been studied by gas chromatography. By the use of mordenite treated with hydrochloric acid solution, the tailing peak of methane showed from untreated mordenite was satisfactorily reduced, although it was difficult to separate it from carbon monoxide with a column activated at $300^{\circ}C$. Using a column activated at $350^{\circ}C$, methane could be separated from carbon monoxide easily but only carbon monoxide eluted as a bad defined peak. Mordenite treated with sodium chloride solution was generally similar to chromatograms obtained by using the untreated mordenite. Both the above chemical treatments of mordenite had little effect on the separations of argon and nitrogen. The separations and the HETP values obtained from natural zeolite mordenite treated with continuously hydrochloric acid and sodium chloride solutions were almost identical with those obtained with synthetic molecular sieve 5A zeolite. On the other hand, the efficiency of column was good in the range 20~3Oml/min of the carrier helium gas rate.

• Elastomers and Composites
• /
• v.34 no.2
• /
• pp.156-176
• /
• 1999

Rubber chemicals such as accelerators, antidegradants, vulcanizing agents, processing agents and retarders are very important to the production and protection of tires and rubber goods. The use of accelerators and antidegradants are evaluated in various tire components. This paper will focus on how to vulcanize tires economically and maintain the physical properties of each tire component without severe degradation due to oxygen, heat and ozone. Also, new non-nitrosoamine accelerators and non-staining antiozonants will be discussed. Lastly, the future requirements of antidegradants and accelerators in the tire industry will be reviewed. Tires have been vulcanized with Sulfenamides as primary accelerators and either Guamdine's or Thiurams as secondary accelerators to achieve proper properties at service conditions. However, interior components such as the carcass can be vulcanized with Thiazoles as a primary accelerator to cure faster than the external components. Using the combination of Sulfenamide with secondary accelerators in a tire tread compound and the combination of a Thiazole and Guanidine in a carcass compound will be presented with performance data. Uniroyal Chemical and another Rubber Chemical Manufacturer have developed, "Tetrabenzyl Thiuram Disulfide," (TBzTD) as a non-Nitrosoamine accelerator, which could replace Nitrosoamine generating Thiurams. This new accelerator has been evaluated in a tread compound as a secondary accelerator. Also, Flexsys has developed N-t-butyl-2-benzothiazole Sulfenamide (TBSI) as a non-Nitrosoamine accelerator which could replace 2-(Morpholinothio) -benzothiazole (MBS), a scorch delayed Sulfendamide accelerator. TBSI has been evaluated in a Natural Rubber (NR) belt skim compound vs. MBS. An optimum low rolling resistant cure system has been developed in a NR tread with Dithiomorpholine (DTDM). Also, future requirements for developing accelerators will be discussed such as the replacement of DTDM and other stable crosslink systems. Antidegradants are divided into two different types for use in tire compounds. Internal tire compounds such as apex, carcass, liner, wire breaker, cushion, base tread and bead compounds are protected by antioxidants against degradation from oxygen and heat due to mechanical shear. The external components such as sidewall, chafer and cap tread com-pounds are protected from ozone by antiozonants and waxes. Various kinds of staining and non-staining antioxidants have been evaluated in a tire carcass compound. Also, various para-phenylene diamine antiozonants have been evaluated in a tire sidewall compound to achieve the improved lifetime of the tire. New non-staining antiozonants such as 2, 4, 6-tris-(N-1, 4-dimethylpentyl-p-phenylene diamine) 1, 3, 5 Trizine (D-37) and un-saturated Acetal (AFS) will be discussed in the tire sidewall to achieve better appearance. The future requirements of antidegradants will be presented to improve tire performance such as durability, better appearance and longer lasting tires.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.11
• /
• pp.5284-5289
• /
• 2011

This study focused to evaluate thermal transmittance(U-value) performance of sliding type of aluminum alloy window frame(AAWF) with double glazing(DG) and glazing spacer and that without thermal breaker in winter and summer season by two dimensional steady state heat transfer analysis. The AAWE was installed to an existing educational facilities in Seosan area which is the southern region of the Korean Peninsula. Analysis of 2D steady-state heat transfer was performed through the use of BISCO as calculation and simulation program. U-value and temperature factors were calculated. The results are as followed. First, the isotherm simulation shows that AAWF with double glazing have serious differences from recently proposed window thermal performance standards such as Insulation Performance of Windows and Doors of Building Energy Saving Design Standards and the results of calculation of thermal transmittance performance of AAWF and DG are U=9.631 W/$m^2K$, U=2.382 W/$m^2K$ respectively during winter and summer season. Second, the results of analysis of heat transfer analysis, calculated by simulation, shows that 225% of heat is lost comparing with thermal performance standards U=4.0 W/$m^2K$ of general double glazing among those standards on AAWF without thermal breaker.

• International conference on construction engineering and project management
• /
• 2009.05a
• /
• pp.525-536
• /
• 2009

The current residential process adheres to a traditional method of construction involving wood framing on-site on poured concrete foundations which has been widely applied in North America. A conventional residential construction process can include seventeen distinct stages ranging from stake-out to pre-occupancy inspection. The current practice possesses short comings including high construction material wastes, long scheduling timelines, adverse weather conditions, poor quality, low efficiencies and negative environmental impacts from transportation and equipment use. Over CAN $5 billion dollars was spent in the construction sector during 2007 in Canada. Previous findings in CO₂ emissions during the construction process of a conventional dwelling emphasize more than 45 tonnes of CO₂ emissions. Hence, in Alberta alone during 2007, almost 50,000 residential units would release more than two million tonnes of CO₂. These numbers demonstrate the economical and environmental impact in building construction and its relationship with CO₂ emissions. The aim of this paper is to quantify the CO₂ emissions from the current residential construction process in order to establish the baseline for CO₂ emission reduction opportunities. The quantification collection methodology will be approached by identifying the seventeen various stages of construction and quantifying the contributions of CO₂ from specific activities and their impacts of work for each stage. The approach of separating these into separate stages for collection will allow for independent opportunities for analysis from various independent contractors from the entire scope of work. The use of BIM will be implemented to efficiently quantify CO₂ emissions. Based on the CO₂ quantification baseline, emission reduction opportunities such as an industrialized construction process will be introduced that allows homebuilders to reduce the environmental and economical impact of home construction while enabling them to produce higher quality, more energy efficient homes in a safer and shorter period of time.

• Journal of the Korea Concrete Institute
• /
• v.24 no.3
• /
• pp.275-283
• /
• 2012

Steel Plate for Rebar Connection was recently developed to splice rebars in delayed slab-wall joints in high-rise building, slurry wall-slab joints, temporary openings, etc. It consists of several couplers and a thin steel plate with shear key. Cyclic loading tests on slab-wall joints were conducted to verify structural behavior of the joints having Steel Plate for Rebar Connection. For comparison, joints with Rebend Connection and without splices were also tested. The joints with Steel Plate for Rebar Connection showed typical flexural behavior in the sequence of tension re-bar yielding, sufficient flexural deformation, crushing of compression concrete, and compression rebar buckling. However, the joints with Rebend Connection had more bond cracks in slabs faces and spalling in side cover-concrete, even though elastic behavior of the joints was similar to that of the joints with Steel Plate for Re-bar Connection. Consequently, the joints with Rebend Connection had less strengths and deformation capacities than the joints with Steel Plate for Re-bar Connection. In addition, stiffness of the joints with Rebend Connection degraded more rapidly than the other joints as cyclic loads were applied. This may be caused by low elastic modulus of re-straightened rebars and restraightening of kinked bar. For two types of diameters (13mm and 16mm) and two types of grades (SD300 and SD400) of rebars, the joints with Steel Plate for Rebar Connection had higher strength than nominal strength calculated from actual material properties. On the contrary, strengths of the joints with Rebend Connection decreased as bar diameter increased and as grade becames higher. Therefore, Rebend Connection should be used with caution in design and construction.

• Journal of Venture Innovation
• /
• v.5 no.1
• /
• pp.107-127
• /
• 2022

Global challenges such as the corona pandemic, climate change and the war-on-tech ensure that the demand who the technologies of the future develops and monitors prominently for will be on the agenda. Development of, and applications in, agrifood, biotech, high-tech, medtech, quantum, AI and photonics are the basis of the future earning capacity of the Netherlands and contribute to solving societal challenges, close to home and worldwide. To be like the Netherlands and Europe a strategic position in the to obtain knowledge and innovation chain, and with it our autonomy in relation to from China and the United States insurance, clear choices are needed. Brainport Eindhoven: Building on Philips' knowledge base, there is create an innovative ecosystem where more than 7,000 companies in the High-tech Systems & Materials (HTSM) collaborate on new technologies, future earning potential and international value chains. Nearly 20,000 private R&D employees work in 5 regional high-end campuses and for companies such as ASML, NXP, DAF, Prodrive Technologies, Lightyear and many others. Brainport Eindhoven has a internationally leading position in the field of system engineering, semicon, micro and nanoelectronics, AI, integrated photonics and additive manufacturing. What is being developed in Brainport leads to the growth of the manufacturing industry far beyond the region thanks to chain cooperation between large companies and SMEs. South-Holland: The South Holland ecosystem includes companies as KPN, Shell, DSM and Janssen Pharmaceutical, large and innovative SMEs and leading educational and knowledge institutions that have more than Invest €3.3 billion in R&D. Bearing Cores are formed by the top campuses of Leiden and Delft, good for more than 40,000 innovative jobs, the port-industrial complex (logistics & energy), the manufacturing industry cluster on maritime and aerospace and the horticultural cluster in the Westland. South Holland trains thematically key technologies such as biotech, quantum technology and AI. Twente: The green, technological top region of Twente has a long tradition of collaboration in triple helix bandage. Technological innovations from Twente offer worldwide solutions for the large social issues. Work is in progress to key technologies such as AI, photonics, robotics and nanotechnology. New technology is applied in sectors such as medtech, the manufacturing industry, agriculture and circular value chains, such as textiles and construction. Being for Twente start-ups and SMEs of great importance to the jobs of tomorrow. Connect these companies technology from Twente with knowledge regions and OEMs, at home and abroad. Wageningen in FoodValley: Wageningen Campus is a global agri-food magnet for startups and corporates by the national accelerator StartLife and student incubator StartHub. FoodvalleyNL also connects with an ambitious 2030 programme, the versatile ecosystem regional, national and international - including through the WEF European food innovation hub. The campus offers guests and the 3,000 private R&D put in an interesting programming science, innovation and social dialogue around the challenges in agro production, food processing, biobased/circular, climate and biodiversity. The Netherlands succeeded in industrializing in logistics countries, but it is striving for sustainable growth by creating an innovative ecosystem through a regional industry-academic research model. In particular, the Brainport Cluster, centered on the high-tech industry, pursues regional innovation and is opening a new horizon for existing industry-academic models. Brainport is a state-of-the-art forward base that leads the innovation ecosystem of Dutch manufacturing. The history of ports in the Netherlands is transforming from a logistics-oriented port symbolized by Rotterdam into a "port of digital knowledge" centered on Brainport. On the basis of this, it can be seen that the industry-academic cluster model linking the central government's vision to create an innovative ecosystem and the specialized industry in the region serves as the biggest stepping stone. The Netherlands' innovation policy is expected to be more faithful to its role as Europe's "digital gateway" through regional development centered on the innovation cluster ecosystem and investment in job creation and new industries.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.

• Korea Journal of Hospital Management
• /
• v.8 no.1
• /
• pp.135-164
• /
• 2003

The operating room is the major facility that costs the highest investment per unit area in a hospital. It requires commitment of hospital resources such as manpower, equipments and material. The quantity of these resources committed actually differs from one type of operation to another. Because of this, it is not an easy task to allocate the operating cost to individual clinical departments that share the operating room. A practical way to do so may be to collect and add the operating costs incurred by each clinical department and charge the net cost to the account of the corresponding clinical department. It has been customary to allocate the cost of the operating room to the account of each individual department on the basis of the ratio of the number of operations of the department or the total revenue by each operating room. In an attempt to set up more rational cost allocation method than the customary method, this study proposes a new cost allocation method that calls for itemizing the operation cost into its constituent expenses in detail and adding them up for the operating cost incurred by each individual department. For comparison of the new method with the conventional method, the operating room in the main building of hospital A near Seoul is chosen as a study object. It is selected because it is the biggest operating room in hospital A and most of operations in this hospital are conducted in this room. For this study the one-month operation record performed in January 2001 in this operating room is analyzed to allocate the per-month operation cost to six clinical departments that used this operating room; the departments of general surgery, orthopedic surgery, neuro-surgery, dental surgery, urology, and obstetrics & gynecology. In the new method(or method 1), each operation cost is categorized into three major expenses; personnel expense, material expense, and overhead expense and is allocated into the account of the clinical department that used the operating room. The method 1 shows that, among the total one-month operating cost of 814,054 thousand wons in this hospital, 163,714 thousand won is allocated to GS, 335,084 thousand won to as, 202,772 thousand won to NS, 42,265 thousand won to uno, 33,423 thousand won to OB/GY, and 36.796 thousand won to DS. The allocation of the operating cost to six departments by the new method is quite different from that by the conventional method. According to one conventional allocation method based on the ratio of the number of operations of a department to the total number of operations in the operating room(method 2 hereafter), 329,692 thousand won are allocated to GS, 262,125 thousand won to as, 87,104 thousand won to NS, 59,426 thousand won to URO, 51.285 thousand won to OB/GY, and 24,422 thousand won to DS. According to the other conventional allocation method based on the ratio of the revenue of a department(method 3 hereafter), 148,158 thousand won are allocated to GS, 272,708 thousand won to as, 268.638 thousand won to NS, 45,587 thousand won to uno, 51.285 thousand won to OB/GY, and 27.678 thousand won to DS. As can be noted from these results, the cost allocation to six departments by method 1 is strikingly different from those by method 2 and method 3. The operating cost allocated to GS by method 2 is about twice by method 1. Method 3 makes allocations of the operating cost to individual departments very similarly as method 1. However, there are still discrepancies between the two methods. In particular the cost allocations to OB/GY by the two methods have roughly 53.4% discrepancy. The conventional methods 2 and 3 fail to take into account properly the fact that the average time spent for the operation is different and dependent on the clinical department, whether or not to use expensive clinical material dictate the operating cost, and there is difference between the official operating cost and the actual operating cost. This is why the conventional methods turn out to be inappropriate as the operating cost allocation methods. In conclusion, the new method here may be laborious and cause a complexity in bookkeeping because it requires detailed bookkeeping of the operation cost by its constituent expenses and also by individual clinical department, treating each department as an independent accounting unit. But the method is worth adopting because it will allow the concerned hospital to estimate the operating cost as accurately as practicable. The cost data used in this study such as personnel expense, material cost, overhead cost may not be correct ones. Therefore, the operating cost estimated in the main text may not be the same as the actual cost. Also, the study is focused on the case of only hospital A, which is hardly claimed to represent the hospitals across the nation. In spite of these deficiencies, this study is noteworthy from the standpoint that it proposes a practical allocation method of the operating cost to each individual clinical department.