• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.10
• /
• pp.3251-3261
• /
• 1996

Flows were measured in an unshrouded centrifugal impeller. By using a single slanted hot-wire probe and a Kiel probe mounted on the impeller hub disk, the 3-D relative velocities and the rotary stagnation pressures were measured in seven circumferential planes between the inlet and outlet of the impeller rotating at 700 rpm, which diameter is 0.39 meter, and the static pressures and the slip factor at the impeller outlet were estimated from the measured values. Measurements were made for three flow rates corresponding to zero incidence and two others with the greater and the smaller one than zero. From the measured data in these flow rates, the followings were investigated in the impeller passage, the variation of the primary and secondary flows, the leakage flows, the wake's position and its size, the static pressure rise and the loss production mechanism. Furthermore the static pressure and the slip factor were compared with the results of inviscid Quasi-3D calculation.

• Journal of Broadcast Engineering
• /
• v.2 no.1
• /
• pp.16-23
• /
• 1997

Among the main technologies to implement 3D TV succeeding HDTV, multi-viewpoint image display technique is rising as an important issue, which can display the viewpoint-dependent images corresponding to viewer's position. This paper presents a novel method that solves too much computational overload that is main drawback of previous methods. Using down sampling technique, multiresolution EPIs are made from multi-viewpoint image set and trace lines are detected in the lowest resolution EPI. The parameters of detected trace lines are transferred to higher resolution EPIs and revised by utilizing the information of the previous resolution EPI. This procedure is iterated until orignal resolution EPI. Using the proposed method, we have achieved the reduction of computational time and the robustness to noise in comparison to previous method.

• Transactions of Materials Processing
• /
• v.18 no.3
• /
• pp.268-273
• /
• 2009

Ultraviolet nanoimprint lithography (UV-NIL), which is performed at a low pressure and at room temperature, is known as a low cost method for the fabrication of nano-scale patterns. In the patterning process, maintaining the uniformity of the residual layer is critical as the pattern transfer of features to the substrate must include the timed etch of the residual layer prior to the etching of the transfer layer. In pursuit of a thin and uniform residual layer thickness, the initial volume and the position of each droplet both need to be optimized. However, the monomer mixtures of resin had a tendency to evaporate. The evaporation rate depends on not only time, but also the initial volume of the monomer droplet. In order to decide the initial volume of each droplet, the accurate prediction of evaporation behavior is required. In this study, the theoretical model of the evaporation behavior of resin droplets was developed and compared with the available experimental data in the literature. It is confirmed that the evaporation rate of a droplet is not proportional to the area of its free surface, but to the length of its contact line. Finally, the parameter of the developed theoretical model was calculated by curve fitting to decide the initial volume of resin droplets.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.199-200
• /
• 2006

It will not be an exaggeration to say that one of the most important features of RT (Rapid Tooling) technology is to easy manufacturing complex shape of cooling channel in injection mold. That is, RT technology is hardly influenced complex shape of tool, Therefore, mold designer can optimize the position and shape of cooling channel whatever they want. In this study, we optimized cooling channel through CAE analysis to solve the problem; prototype-connector-mold applied conventional cooling channel, locally warped by internal stress: The effect of three-dimensional cooling channel was supported by simulation result. But it is impossible to produce injection mold applied three-dimensional cooling channel through machining operation. Therefore, we produced the prototype-connector-mold with three-dimensional cooling channel using Direct Metal Laser Sintering (DMLS) process, and get good-quality prototype-connector without warpage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.9A
• /
• pp.1083-1090
• /
• 2004

In this paper, a meander-type microstrip patch antenna for application in 5GHz-hand is designed and fabricated To obtain enough bandwidth in VSWR≶2, the foam is inserted between substrate and ground plane, the coaxial probe source 1S used Antenna is simulated varing the length and width of meander line, the position of probe feeding and the thick of airgap. Later antenna is fabricated with optimizated antenna parameter. The measured result of Fabricated antenna obtained IGHz(l7.5%) bandwidth in VSWR≶2, the gain of 7.3-9.5dBi, Unidirectional pattern.

• Korean Journal of Veterinary Research
• /
• v.32 no.4
• /
• pp.555-567
• /
• 1992

In this study gene encoding structural proteins of a CPV isolate was cloned and sequenced to elucidate the molecular genetical properties of the canine parvoviruses isolated from the field. Six recombinant plasmids of pEP3, p1471, p2070, pEP069, pEP338 and p14711p were constructed from the map positions 22 to 98 of RF DNA to clone the VP1 and VP2 genes of CPV-V20. Sequentialy the gene comprising 3780 nucleotides were sequenced by dideoxy chain termination method. When nucleotide sequence of gene encoding the structural proteins of CPV-V20 was compared with those of other strains, CPV-N, CPV-d and CPV-780929 published previously, DNA, homologies to CPV-V20 were 99.87% with CPV-N, 99.73% with CPV-d, 96.85% with CPV-780929 and 98.4% with FPLV-Carl, respectively. The DNA sequence data of CPV-V20 showed seven point mutations and also deletion of 135 nucleotides from the nucleotide position 4745 to 4879 located in the 3'-noncoding region of CPV-N.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.40 no.1
• /
• pp.32-36
• /
• 2014

Preoperative surgical simulation in orthognathic surgery has progressed in recent years; the movement of the mandible can be anticipated through three-dimensional (3D) simulation surgery before the actual procedure. In this case report, the mandible was moved to the intended postoperative occlusion through preoperative surgical 3D simulation. Right-side condylar movement change was very slight in the surgical simulation, suggesting the possibility of mandibular surgery that included only left-side ramal osteotomy. This case report describes a patient with a mild asymmetric facial profile in which the mandibular menton had been deviated to the right and the lips canted down to the left. Before surgery, three-dimensional surgical simulation was used to evaluate and confirm a position for the condyle as well as the symmetrical postoperative state of the face. Facial asymmetry was resolved with minimal surgical treatment through unilateral intraoral vertical ramus osteotomy on the left side of the mandible. It would be a valuable complement for the reduction of the surgical treatment if one could decide with good predictability when an isolated intraoral vertical ramus osteotomy can be done without a compensatory osteotomy on the contralateral side.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.12
• /
• pp.1067-1071
• /
• 2013

A 3D visual sensing method using a laser structured beam is presented for robotic tracking applications in a simple and reliable manner. A cylindrical shaped laser structured beam is proposed to measure the pose and position of the target surface. When the proposed laser beam intersects on the surface along the target trajectory, an elliptic pattern is generated. Its ellipse parameters can be induced mathematically by the geometrical relationship of the sensor coordinate and target coordinate. The depth and orientation of the target surface are directly determined by the ellipse parameters. In particular, two discontinuous points on the ellipse pattern, induced by seam trajectory, indicate mathematically the 3D direction for robotic tracking. To investigate the performance of this method, experiments with a 6 axis robot system are conducted on two different types of seam trajectories. The results show that this method is very suitable for robot seam tracking applications due to its excellence in accuracy and efficiency.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.4
• /
• pp.49-53
• /
• 2018

Parabolic offset antenna is widely used for wireless communication system. The general structure of parabolic offset antenna system is composed of supporting stand and RF devices under parabolic reflector. However sidelobe distortion in gain pattern is occurred by supporting stand and RF devices. Depending on position of subsidiary devices, angle of sidelobe distortion can be changed. In this paper we describe method for sidelobe distortion suppression using raytracing. We calculate 3D vector for sidelobe distortion suppression zone by raytracing method and compare when subsidiary device is in sidelobe distortion suppression zone or not. By comparison, we show method for parabolic antenna sidelobe distortion suppression.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4A
• /
• pp.312-319
• /
• 2005

In this paper, a meander-type microstrip patch antenna for application in 5GHz-band is designed and fabricated. To obtain enough bandwidth in VSWR<2, the foam is inserted between substrate and ground plane, the coaxial probe source is used. Antenna is simulated varing the length and width of meander line, the position of probe feeding and the thick of airgap. Later anterlna is fabricated with optimizated antenna parameter. The measured result of Fabricated antenna obtained $1GHz(17.5\%)$ bandwidth in VSWR<2$, the gain of $.3\sim9.5$dBi, Unidirectional pattern.