• Geomechanics and Engineering
• /
• v.30 no.2
• /
• pp.169-185
• /
• 2022

The urbanization and increasing rate of population demands effective means of transportation system (basement and tunnels) as well as high-rise building (resting on piled foundation) for accommodation. Therefore, it unavoidable to construct basements (i.e., excavation) nearby piled foundation. Since the basement excavation inevitably induces soil movement and stress changes in the ground, it may cause differential settlements to nearby piled raft foundation. To understand settlement and load transfer mechanism in the piled raft due to excavation-induced stress release, numerical parametric studies are carried out in this study. The effects of excavation depths (i.e., formation level) relative to piled raft were investigated by simulating the excavation near the pile shaft (i.e., H_e/L_p=0.67), next to (H_e/L_p=1.00) and below the pile toe (H_e/L_p=1.33). In addition, effects of sand density and raft fixity condition were investigated. The computed results have revealed that the induced settlement, tilting, pile lateral movement and load transfer mechanism in the piled raft depends upon the embedded depth of the diaphragm wall. Additional settlement of the piled raft due to excavation can be account for apparent loss of load carrying capacity of the piled raft (ALPC). The highest apparent loss of piled raft capacity ALPC (on the account of induced piled raft settlement) of 50% was calculated in in case of H_e/L_p = 1.33. Furthermore, the induced settlement decreased with increasing the relative density from 30% to 90%. On the contrary, the tilting of the raft increases in denser ground. The larger bending moment and lateral force was induced at the piled heads in fixed and pinned raft condition.

• Nuclear Engineering and Technology
• /
• v.53 no.12
• /
• pp.3879-3891
• /
• 2021

A heat pipe residual heat removal system is proposed to be incorporated into the reactor driven subcritical (RDS) facility, which has been proposed by MIT Nuclear Reactor Laboratory for testing and demonstrating the Fluoride-salt-cooled High-temperature Reactor (FHR). It aims to reduce the risk of the system operation after the shutdown of the facility. One of the main components of the system is an air-cooled heat pipe heat exchanger. The alkali-metal high-temperature heat pipe was designed to meet the operation temperature and residual heat removal requirement of the facility. The heat pipe model developed in the previous work was adopted to simulate the designed heat pipe and assess the heat transport capability. 3D numerical simulation of the subcritical facility active zone was performed by the commercial CFD software STAR CCM + to investigate the operation characteristics of this proposed system. The thermal resistance network of the heat pipe was built and incorporated into the CFD model. The nominal condition, partial loss of air flow accident and partial heat pipe failure accident were simulated and analyzed. The results show that the residual heat removal system can provide sufficient cooling of the subcritical facility with a remarkable safety margin. The heat pipe can work under the recommended operation temperature range and the heat flux is below all thermal limits. The facility peak temperature is also lower than the safety limits.

• Structural Engineering and Mechanics
• /
• v.83 no.5
• /
• pp.693-707
• /
• 2022

Bonded joints have proven their performance against conventional joining processes such as welding, riveting and bolting. The single-lap joint is the most widely used to characterize adhesive joints in tensile-shear loadings. However, the high stress concentrations in the adhesive joint due to the non-linearity of the applied loads generate a bending moment in the joint, resulting in high stresses at the adhesive edges. Geometric optimization of the bonded joint to reduce this high stress concentration prompted various researchers to perform geometric modifications of the adhesive and adherends at their free edges. Modifying both edges of the adhesive (spew) and the adherends (bevel) has proven to be an effective solution to reduce stresses at both edges and improve stress transfer at the inner part of the adhesive layer. The majority of research aimed at improving the geometry of the plate and adhesive edges has not considered the effect of temperature and water absorption in evaluating the strength of the joint. The objective of this work is to analyze, by the finite element method, the stress distribution in an adhesive joint between two 2024-T3 aluminum plates. The effects of the adhesive fillet and adherend bevel on the bonded joint stresses were taken into account. On the other hand, degradation of the mechanical properties of the adhesive following its exposure to moisture and temperature was found. The results clearly showed that the modification of the edges of the adhesive and of the bonding agent have an important role in the durability of the bond. Although the modification of the adhesive and bonding edges significantly improves the joint strength, the simultaneous exposure of the joint to temperature and moisture generates high stress concentrations in the adhesive joint that, in most cases, can easily reach the failure point of the material even at low applied stresses.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.66-66
• /
• 2021

2011년에 일본 도호쿠 지방 태평양 해역에서 규모 9.0의 지진이 발생하여 거대한 쓰나미가 일본 본토 해안을 침수시켰다. 이로 인해, 정확한 피해규모가 파악되기 어려울 정도로 막대한 인명과 재산피해를 입게 되었다. 센다이지역의 경우 쓰나미로 인해 해안에 위치한 약 3.8 평방킬로미터의 방풍림이 모두 전복되었고 일부는 유목이 되어 쓰나미와 함께 내륙으로 흘러들어가 곳곳에 퇴적되어 농지를 훼손하고 가옥에 피해를 주었다. 따라서, 본 연구는 유목의 발생과 흐름에 따른 거동을 수치적으로 분석하여, 폭우나 쓰나미와 같은 거대흐름과 산지와 방풍림 등에서 발생하는 유목의 발생과 거동과정을 예측하고, 흐름과 유목 거동에 따른 피해지역을 선별할 수 있는 방법을 구축하기 위한 초기단계로서, 이를 위해 유목의 발생과정의 역학적 모델링을 수치모듈에 적용하였고 이를 활용하여 수치모의를 수행하였다. 흐름분석을 위해 쓰인 모형은 홍수범람 모형인 Nays2D Flood 이며 천수방정식을 기본으로 한다. 쓰나미의 흐름은 해안가의 방풍림지역을 상류단 경계조건으로 하여 발생 당시 관측된 수심변화를 본 모형의 상류단 경계조건으로 입력하였다. 상류단 경계조건에서 쓰나미의 유속은 수심에 따른 파속으로 계산하였다. 본 연구에서는 또한 유목의 발생과 흐름거동을 기존에 개발된 입자법 기반의 유목동역학모형을 활용하여 수치적으로 모델링 하였다. 유목은 유연성이 없는 원주형 강체로 가정하였고 초기설정으로는, 방풍림지역에 30만개의 유목이 하상의 수직방향으로 배치되어있는 것으로 가정하였다. 여기서, 본 연구에서는 쓰나미가 발생하면 흐름에 따른 항력으로 인해 수직방향으로 배치된 유목이 부러지며, 흐름과 함께 흘러가는 현상을 모델링하였다. 본 연구는 폭우나 쓰나미와 같은 거대흐름으로 인해 발생할 수 있는 유송잡물과 유목의 거동을 예측분석하는 기초연구자료로 활용될 수 있으며, 더 나아가 유목의 발생과정까지 수치적으로 재현하는 모델링을 수행하였기 추후에, 산지와 하천에서 발생할 수 있는 유송잡물의 발생과 연행 과정을 보다 세부적으로 예측할 수 있는 기초방법론으로 쓰일 수 있을 것으로 판단된다.

• Geomechanics and Engineering
• /
• v.36 no.6
• /
• pp.545-561
• /
• 2024

Piled raft foundation has become widely used in the recent years because it can increase bearing capacity of foundation with control settlement. The design for a piled raft in terms vertical load and lateral load need to understands contribution load behavior to raft and pile in piled raft foundation system. The load-bearing behavior of the piled raft, especially concerning lateral loads, is highly complex and challenge to analyze. The complex mechanism of piled rafts can be clarified by using three dimensional (3-D) Finite Element Method (FEM). Therefore, this paper focuses on free-standing head pile group, on-ground piled raft, and embedded raft for the piled raft foundation systems. The lateral resistant of piled raft foundation was investigated in terms of relationship between vertical load, lateral load and displacement, as well as the lateral load sharing of the raft. The results show that both vertical load and raft position significantly impact the lateral load capacity of the piled raft, especially when the vertical load increases and the raft embeds into the soil. On the same condition of vertical settlement and lateral displacement, piled raft experiences a substantial demonstrates a higher capacity for lateral load sharing compared to the on-ground raft. Ultimately, regarding design considerations, the piled raft can reliably support lateral loads while exhibiting behavior within the elastic range, in which it is safe to use.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.3
• /
• pp.63-74
• /
• 1999

A sliding mode fuzzy control (SMFC) algorithm is presented for vibration of large structures. Rule-base of the fuzzy inference engine is constructed based on the sliding mode control, which is one of the nonlinear control algorithms. Fuzziness of the controller makes the control system robust against the uncertainties in the system parameters and the input excitation. Non-linearity of the control rule makes the controller more effective than linear controllers. Design procedure based on the present fuzzy control is more convenient than those of the conventional algorithms based on complex mathematical analysis, such as linear quadratic regulator and sliding mode control(SMC). Robustness of presented controller is illustrated by examining the loop transfer function. For verification of the present algorithm, a numerical study is carried out on the benchmark problem initiated by the ASCE Committee on Structural Control. To achieve a high level of realism, various aspects are considered such as actuator-structure interaction, modeling error, sensor noise, actuator time delay, precision of the A/D and D/A converters, magnitude of control force, and order of control model. Performance of the SMFC is examined in comparison with those of other control algorithms such as $H_{mixed 2/{\infty}}$ optimal polynomial control, neural networks control, and SMC, which were reported by other researchers. The results indicate that the present SMFC is an efficient and attractive control method, since the vibration responses of the structure can be reduced very effectively and the design procedure is simple and convenient.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.2
• /
• pp.90-98
• /
• 2006

Signals captured from a Combo calibration standard tube paly a crucial role in the evaluation of motorized rotating pancake coil (MRPC) probe signals from steam generator (SG) tubes in nuclear power plants (NPPs). Therefore, the Combo tube signals should be consistent and accurate. However, MRPC probe signals are very easily affected by various factors around the tubes so that they can be distorted in their amplitudes and phase angles which are the values specifically used in the evaluation. To overcome this problem, in this study, we explored possibility of simulation to be used as a practical calibration tool far the evaluation of real field signals. For this purpose, we investigated the characteristics of a MRPC probe and a Combo tube. And then using commercial software (VIC-3D) we simulated a set of calibration signals and compared to the experimental signals. From this comparison, we verified the accuracy of the simulated signals. Finally, we evaluated two defects using the simulated Combo tube signals, and the results were compared with those obtained using the actual field calibration signals.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.5
• /
• pp.1907-1914
• /
• 2013

Textile-type heat exchangers installed on the tunnel walls for facilitating ground source heat pump systems, so called "energy textile", was installed in an abandoned railroad tunnel around Seocheon, South Korea. To evaluate thermal performance of the energy textile, a series of long-term monitoring was performed by artificially applying daily intermittent cooling and heating loads on the energy textile. In the course of the experimental measurement, the inlet and outlet fluid temperatures of the energy textile, pumping rate, temperature distribution in the ground, and air temperature inside the tunnel were continuously measured. From the long-term monitoring, the heat exchange rate was recorded as in the range of 57.6~143.5 W per one unit of the energy textile during heating operation and 362.3~558.4 W per one unit during cooling operation. In addition, the heat exchange rate of energy textile was highly sensitive to a change in air temperature inside the tunnel. The field measurements were verified by a 3D computational fluid dynamics analysis (FLUENT) with the consideration of air temperature variation inside the tunnel. The verified numerical model was used to evaluate parametrically the effect of drainage layer in the energy textile.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.2
• /
• pp.307-318
• /
• 2015

In this study, the efficiency of two-dimensional inundation analysis using road network was demonstrated in order to reduce the simulation time of numerical model in urban area. For this objective, three simulation conditions were set up: Case 1 considered only inundation within road zone, while Case 2 and 3 considered inundation within road and building zone together. Accordingly, Case 1 used grids generated based on road network, while Case 2 and 3 used uniform and non-uniform grids for whole study area, respectively. Three simulation conditions were applied to Samsung drainage where flood damage occurred due to storm event on Sep. 21, 2010. The efficiency of suggested method in this study was verified by comparison the accuracy and simulation time of Case 1 and those of Case 2 and 3. The results presented that the simulation time was fast in the order of Case 1, 2 and 3, and the fit of inundation area between each case was more than 85% within road zone. Additionally, inundation area of building zone estimated from inundation rating index gave a similar agreement under each case. As a result, it is helpful for study on real-time inundation forecast warning to use a proposed method based on road network and inundation rating index for building zone.

• Journal of the Korean Academy of Child and Adolescent Psychiatry
• /
• v.5 no.1
• /
• pp.108-117
• /
• 1994

Twenty nine children with autism and thirty children with mental retardation were examined for association between autism and chromosomal disorders including fragile X. The peripheral blood was cultured in Medium 199 with methotrexate and without methorexate for 70 hours. Thirty metaphase cells in each case were karyotyped in all samples. Chromosomal abnormalities were found in 11 cases(37.9%) of autistic disorder and 10 cases (33.3%) of mental retardation, but in none of fragile(X)(q27.3) from all cases. Chromosomal abnormalities were present on group A, C, D and X in autistic disorder and on group A, B, C, D, E and X in mental retardation. No specific chromosomal region was found in both autistic disorder and mental retardation. Types of chromosomal disorders were only fragile and/or gap but no numerical abnormality was present in all cases. Number of cells which revealed fragile sites were 31 cells(3.6%) out of 870 cells in autistic disorder and 29 cells(3.2%) out of 900 cells in mental retardation Number of cells which revealed gaps were 43 cells(4.9%) out of 870 cells in autistic disorder and 35 cells(3.9%) out of 900 cells in mental retardation. Autistic disorder may not be directly correlated with fragile X but with nonspecific chromosomal breakages from these data.