• 한국전자파학회논문지
• /
• 제19권7호
• /
• pp.791-799
• /
• 2008

본 논문에서는 $DC{\sim}18\;GHz$에서 동작하는 GTEM 셀 설계를 위한 전자파 모델링과 회로망 해석 기법을 제시하였다. GTEM 셀의 동축선 입력 급전부의 모드 변환기, 전송선 길이가 5미터인 확장형 사각 동축선 그리고 전송부 동축선의 전류와 입력단으로부터 입사되는 전자파를 정합시킬 수 있는 종단 부하로 구성되는 3차인 전자파 수치 해석 모델을 제시하였다. GTEM cell의 급전부, 전송선부, 종단 부하부에 대한 등가 회로망 모델을 제시하였으며, 이를 이용하여 전자파 수치 해석 모델에서 구해진 산란 계수로부터 GTEM cell의 성능 평가 지수인 입력 반사 계수를 계산할 수 있도록 하였다. $DC{\sim}18\;GHz$에서 동작하는 $5.0{\times}2.5{\times}1.7\;m$ 크기의 GTEM cell을 설계, 제작, 성능 평가하여 제안한 기법의 효용성을 입증하였다.

• 한국전자파학회논문지
• /
• 제24권3호
• /
• pp.324-330
• /
• 2013

본 논문은 대기압 환경에서 발생하는 유전체 장벽 방전(dielectric barrier discharge: DBD) 플라즈마의 전자파 산란 특성을 측정하였다. 본 논문에서는 기본적인 DBD 플라즈마 발생기 구조를 병렬로 연결하여 넓은 면적의 플라즈마 발생기를 제작하였고, 14 kV, 4 kHz의 고전압 발생장치를 이용해 플라즈마가 발생하는 것을 확인하였다. 두 개의 혼 안테나와 벡터 네트워크 분석기를 이용해 S-parameter의 비교를 통해 전자파 산란 특성을 측정하였다. 전방 산란의 경우 제작된 플라즈마 발생기의 구조적 특성으로 인해 안테나의 편파에 따라 다른 결과 값을 얻었다. 편파가 수평일 때 최대 2 dB의 산란파 감쇠 특성을 확인할 수 있었다. 또한, 편파가 수평일 경우, 플라즈마 발생기 뒤에 PEC를 설치한 후 후방 산란 특성을 측정하였다. 그 결과, 5 GHz에서 안테나 관찰 각도가 $40^{\circ}C$, $60^{\circ}C$일 때 최대 2 dB 산란파 감쇠 특성을 얻었다.

• 한국수소및신에너지학회논문집
• /
• 제21권3호
• /
• pp.149-157
• /
• 2010

The electromagnetic characteristics of FCEVs (fuel cell electric vehicles) are much different from the existing combustion engine cars as well as hybrid, plug-in-hybrid, and pure electric vehicles due to the high voltage/current generated by a fuel cell stack which uses a compressed hydrogen gas reacted with oxygen. To operate fuel cell stack efficiently, BOP (Balance of Plant) is essential. BOP systems are used many not only for motors in water pump, air blower, and hydrogen recycling pump but also inverters for these motors. Since these systems or components are connected by high voltage cables, EMC (Electromagnetic compatibility) analysis for high voltage/current cable is the most important element to prevent the possible electric functional safety errors. In this paper, electromagnetic fields of high current/voltage cable for FCEVs is studied. From numerical analysis results, time harmonic magnetic field strength of high current/voltage cable have difference of 20～28 dB according to phase. EMI result considered ground effect of FECV at 10 m shows difference of 14.5 dB at 30 MHz and 2.8 dB at 230 MHz compared with general cable.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2049-2057
• /
• 2014

In this paper, a numerical method for analyzing coupling between high-altitude electromagnetic pulse (HEMP) as external field and a shielded twisted pair (STP) cable is proposed, which is based on an expanded chain matrix. Load responses of electromagnetic (EM) field excitation in uniform transmission line (TL) are solved by Baum-Liu-Tesche (BLT) equations in frequency domain, however, it is difficult to apply BLT equations to solve load responses of STP cable because the iteratively changing configuration of each twisted pairs are involved in cable. To avoid this problem and decrease memory and CPU time, we proposed the expanded chain matrix modeling method that is calculated using ABCD parameters, and applied multi-conductor transmission line (MTL) theory to consider the EMP coupling effectiveness of each twisted pairs. The results implemented by the proposed method are presented and compared with those obtained by the finite-difference time domain (FDTD) method as a kind of 3D full wave analysis.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권6호
• /
• pp.255-261
• /
• 2005

Recently, the RF inductive discharge or inductively coupled plasma continues to attract growing attention as an effective plasma source in many industrial applications, the best known of which are plasma processing and lighting technology. To the point of lighting sources, the ring-shaped electrodeless fluorescent lamps utilizing an inductively coupled plasma have been objects of interest and research during the last decades, mainly because of their potential for extremely long life, high lamp efficacies, rapid power switching response. In this paper, maxwell 3D finite element analysis program (Ansoft) was used to obtain electromagnetic properties associated with the coil and nearby structures. The electromagnetic emitting properties were presented by 3D simulation software operated at 250 kHz and some specific conditions. The electromagnetic field in the ferrite core was shown to be high and symmetric. An LS-100 luminance meter and a Darsa-2000 spectrum analyzer were used in the experiment. According to data on the lamp tested using high magnetic field ferrite, the optical and thermal wave fields were shown to be high around the ring-shaped electrodeless fluorescent lamp. The optical or light field was high at the center of the bulb rather than around the ferrite core. The light conditions of the bulb were assumed to be complex, depending on the condition of the filler gas, the volume of the bulb, and the frequency of the inverter. Our results have shown coupling between the gas plasma and the field of the light emitted to be nonlinear.

• Journal of Magnetics
• /
• 제16권4호
• /
• pp.374-378
• /
• 2011

Axial Field Permanent Magnet (AFPM) generators are widely applied for the small wind turbine because of the higher power density per unit weight than that of the conventional radial field generator. It is caused by the disc shaped rotor and the stator structures. The generally used AFPM generator, AFER-NS generator, is composed of the two side's external rotors and non-slotted stator without stator core. However, the output voltage and the output power are limited by the large reluctance by the long air-gap flux paths. In this paper, the design study of AFIR-S generator having double side's slotted stator core is accomplished to improve the output generation characteristics. The electromagnetic design analysis and the design improvement of the suggested AFIR-S generator are studied. Firstly, the electromagnetic design analysis was done to increase the power density. Secondly, the design optimizations of the rotor pole-arc ratio of permanent magnet are accomplished to increase the output power and to reduce the cogging torque. Finally, the output performances of AFER-NS and AFIR-S generator are compared with each other. For this study, 3D FEA is applied for the design analysis because of three dimensional electromagnetic structures.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권9호
• /
• pp.412-417
• /
• 2003

In this Paper, we propose a time-domain magnetic field integral equation (TD-MFIE) formulation for analyzing the transient electromagnetic response from three-dimensional (3-D) dielectric bodies. The solution method in this paper is based on the Galerkin's method that involves separate spatial and temporal testing procedures. Triangular patch basis functions are used for spatial expansion and testing functions for arbitrarily shaped 3-D dielectric structures. The time-domain unknown coefficients of the equivalent electric and magnetic currents are approximated tv a set of orthonormal basis function that is derived from the Laguerre polynomials. These basis functions are also used for the temporal testing. Numerical results computed by the proposed method are presented and compared.

• Structural Engineering and Mechanics
• /
• 제78권1호
• /
• pp.1-13
• /
• 2021

In this study, the porothermoelastic problem with the effect of the magnetic field and initial stress was investigated. We applied normal mode analysis to solve the resulting non-dimensional coupled equations. Numerical results for the displacements, temperature distribution, pore pressure, stresses, induced electric field and induced magnetic field distributions are presented graphically and discussed. The medium deformed because of thermal shock and due to the application of the magnetic field, there result an induced magnetic and an induced electric field in the medium. Numerical analyses are given graphically on the square (2D) and cubic (3D) domains to illustrate the effects of the porosity parameter, magnetic field and initial stress parameter on the physical variables.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권3호
• /
• pp.146-154
• /
• 2006

We derived a theory of increasing electromagnetic force which acts on arc column for reducing arcing time between electric contacts. A simulation method of arc velocity is presented by calculating blowout force using 3D FEM and drag force acting on arc column. This paper proposes 3 types arc extinguish chamber of different flux path and presents the specific electromagnetic force and arc velocity of each model by the analysis. The result of analysis and experimental proposes the prediction method of arc time when all conditions are same except external magnetic field.

• 한국자기학회지
• /
• 제24권2호
• /
• pp.66-69
• /
• 2014

유한요소법으로 분할 표시한 연한 X-선 퍼짐관을 설계하였다. 연한 X-선관의 모양설계 및 구체적인 좌표를 설정하고 전자빔 궤적을 OPERA-3D SW 프로그램을 이용하여 시뮬레이션하였다. 음극과 양극인 텅스텐 필라멘트와 타겟에 인가한 전압, 온도, 열전자 일함수 등을 고정하였다. 필라멘트 십자형 모양을 구비한 퍼짐관의 구조에 따른 전자빔의 분포와 초점변화를 분석하여 반도체 공정상의 정전기장 제거용 연한 X-선 퍼짐관 설계를 최적화하였다.